Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT
RM3160E _52 Drivetrain _019687 AXLE AND DIFFERENTIAL _0109438 REAR AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

a.

Remove the 2 bolts and separate the rear disc brake caliper assembly.

NOTICE:

Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.



Hide 42491 3.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 42431 4.REMOVE REAR DISC

Hide 42312E 5.REMOVE REAR AXLE HUB BOLT

a.
C293037
0.771,1.104 1.229,1.104 true 1.385,1.458 1.427,1.99 1.427,1.99 1.688,1.99 true 1.844,0.802 1.844,0.604 1.844,0.604 2.01,0.604 true 1.719,1.906 2.031,2.063 0.313,0.156 10 false *a 0.573,1.01 0.771,1.198 0.198,0.188 10 true *a 2.031,0.531 2.469,0.729 0.438,0.198 10 false SST
*a Service Nut


Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the rear axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

SST
09628-10011  

NOTICE:

Do not damage the threads of the rear axle hub bolts.



Hide 42312E 6.INSTALL REAR AXLE HUB BOLT

a.
C293038
2.24,0.458 2.531,0.458 true 2.896,0.896 2.896,1.167 true 2.063,0.354 2.24,0.552 0.177,0.198 10 true *a 2.823,1.177 3.135,1.333 0.313,0.156 10 false *b
*a Service Nut
*b Washer


Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.


b.

Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the rear axle hub bolts.

·

Do not damage the threads of the rear axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 rear axle hub bolts.


Hide 42431 7.INSTALL REAR DISC

Hide 42491 8.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 9.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

a.

Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 10.ADJUST PARKING BRAKE

Hide 11.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)