1. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.REMOVE FRONT WHEEL RH
51441
4.REMOVE NO. 1 ENGINE UNDER COVER
53875A
5.SEPARATE FRONT FENDER LINER RH
53736
6.REMOVE FRONT FENDER APRON SEAL RH
53295E
7.REMOVE COOL AIR INTAKE DUCT SEAL
12601B
8.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
17750A
9.REMOVE INLET AIR CLEANER ASSEMBLY
17705
10.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
17801
11.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17701
12.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
12327A
13.REMOVE NO. 2 ENGINE MOUNTING STAY RH
12363A
14.REMOVE ENGINE MOVING CONTROL ROD
82121
15.DISCONNECT ENGINE WIRE
Disengage the 2 claws and disconnect the inlet heater water hose and outlet heater water hose.
Disconnect the 12 connectors and 5 clamps.
Remove the 3 bolts and 4 nuts and disconnect the engine wire from the engine assembly.
19500
16.REMOVE IGNITION COIL ASSEMBLY
11201
17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
18.SET NO. 1 CYLINDER TO TDC/COMPRESSION
| *a | Paint Mark |
| *b | Timing Mark |
| *c | Timing Notch (Groove) |
Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover sub-assembly are aligned.
Check that both timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly are facing upward as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.
"A" is not a timing mark.
Place paint marks on the chain sub-assembly in alignment with the timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
11324
19.REMOVE TIMING CHAIN COVER PLATE
Remove the 4 bolts, timing chain cover plate and gasket.
13540
20.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Turn the crankshaft pulley approximately 10° clockwise.
Turn the crankshaft pulley approximately 10° counterclockwise.
| *a | Pin |
| *b | Stopper Plate |
Align the holes of the stopper plate and No. 1 chain tensioner assembly, and insert a pin into the stopper plate hole to lock the No. 1 chain tensioner assembly.
Turn the crankshaft pulley approximately 10° clockwise.
Remove the 2 bolts, No. 1 chain tensioner assembly and gasket.
Make sure not to drop the gasket inside the timing chain cover sub-assembly.
Turn the crankshaft pulley approximately 10° counterclockwise.
13566B
21.REMOVE TIMING CHAIN GUIDE
22.REMOVE TIMING CHAIN COVER TIGHT PLUG
13050
23.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
| *a | Hold |
| *b | Turn |
Using a wrench to hold the hexagonal portion of the camshaft, remove the bolt from the camshaft.
Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.
Separate the camshaft timing gear assembly from the camshaft.
| *a | Narrow |
| *b | Wide |
Separate the chain sub-assembly from the camshaft timing gear assembly, and turn the camshaft timing gear assembly approximately 180°.
Remove the camshaft timing gear assembly.
Do not disassemble the camshaft timing gear assembly.
24.REMOVE CAMSHAFT BEARING CAP
Remove the 11 bolts in several steps in the order shown in the illustration.
Remove the 10 bolts in several steps in the order shown in the illustration.
Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps.
Arrange the removed parts in the correct order.
13511
25.REMOVE CAMSHAFT
Remove the camshaft from the camshaft housing sub-assembly.
13512
26.REMOVE NO. 2 CAMSHAFT
Hold up the chain sub-assembly and remove the No. 2 camshaft from the camshaft housing sub-assembly.
Suspend the chain sub-assembly with a string or equivalent as shown in the illustration.
Be careful not to drop the chain sub-assembly inside the timing chain cover sub-assembly.
13070A
27.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Secure the No. 2 camshaft in a vise by clamping the hexagonal part between aluminum plates.
Do not damage the No. 2 camshaft by tightening the vise excessively.
Remove the bolt and camshaft timing exhaust gear assembly.
Do not disassemble the camshaft timing exhaust gear assembly.
15678A
28.REMOVE OIL CONTROL VALVE FILTER
11811
29.REMOVE NO. 1 CAMSHAFT BEARING
11821
30.REMOVE NO. 2 CAMSHAFT BEARING