Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109591 CYLINDER HEAD GASKET A

1AR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 11310 1.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 17167 4.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 25051 5.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

Hide 22030 6.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 17650 7.REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 12262 8.DISCONNECT NO. 2 VENTILATION HOSE

Hide 44774 9.DISCONNECT UNION TO VACUUM TUBE HOSE

Hide 23814B 10.REMOVE FUEL DELIVERY PIPE

Hide 12.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.

A292247
5.969,2.917 6.219,2.771 false 3.51,5.708 4.646,5.438 false 1.021,2.833 1.031,3.021 false 0.958,0.354 1.271,0.51 0.313,0.156 10 false *a 6.25,0.448 6.563,0.604 0.313,0.156 10 false *b 5.792,2.875 6.104,3.031 0.313,0.156 10 false *c 4.708,5.323 5.021,5.479 0.313,0.156 10 false *1 0.969,3.042 1.281,3.198 0.313,0.156 10 false *c 6.688,3.656 6.844,3.854 0.156,0.198 10 false A 1.646,2.719 1.802,2.917 0.156,0.198 10 false A
*1 Crankshaft Pulley Key - -
*a Approximately 7° *b Approximately 32°
*c Timing Mark - -



b.

Rotate the crankshaft clockwise and align the crankshaft pulley key as shown in the illustration.


c.

Check that the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.

HINT:

"A" is not a timing mark.



d.

Remove the crankshaft pulley bolt.


Hide 13566B 13.REMOVE TIMING CHAIN GUIDE

a.
A196878

Remove the bolt and timing chain guide.


Hide 13540 14.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A196879
2.635,0.542 2.51,0.542 2.51,0.542 2.25,1.052 false 1.49,0.417 1.635,0.417 1.635,0.417 1.938,1.052 false 2.656,0.479 2.833,0.635 0.177,0.156 10 true *b 1.302,0.344 1.469,0.5 0.167,0.156 10 true *a
*a Stopper Plate
*b Plunger


Allow the plunger to extend slightly, and then rotate the stopper plate counterclockwise to release the lock. Once the lock is released, push the plunger into the No. 1 chain tensioner assembly.


b.
A196880
1.76,1.99 2.115,1.896 2.115,1.896 2.188,1.896 false 2.208,1.813 2.385,1.969 0.177,0.156 10 true *a
*a Pin


Move the stopper plate clockwise to set the lock, and insert a pin into the stopper plate hole.


c.
A196877

Remove the 2 bolts, No. 1 chain tensioner assembly and gasket.


Hide 13559 15.REMOVE CHAIN TENSIONER SLIPPER

a.
A196876

Remove the bolt and chain tensioner slipper.


Hide 13561 17.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A196868

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13050 18.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A265376
1.411,0.255 1.624,0.428 0.213,0.173 10 *a 0.07,1.364 0.284,1.537 0.213,0.173 10 *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the camshaft, remove the bolt and camshaft timing gear assembly.

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear assembly.




Hide 13070A 19.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A265377
1.604,0.229 1.792,0.438 0.188,0.208 10 false *a 0.271,1.792 0.458,2 0.188,0.208 10 false *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the No. 2 camshaft, remove the bolt and camshaft timing exhaust gear assembly.

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing exhaust gear assembly.




Hide 11103 20.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A196884
2.479,0.115 2.583,0.26 0.104,0.146 10 false 9 2.333,1.927 2.427,2.083 0.094,0.156 10 true 1 0.844,1.927 0.938,2.104 0.094,0.177 10 false 2 3.208,0.625 3.323,0.771 0.115,0.146 10 false 3 3.198,1.677 3.292,1.833 0.094,0.156 10 false 4 3.229,1.042 3.344,1.188 0.115,0.146 10 false 5 0.833,0.125 0.948,0.281 0.115,0.156 10 false 6 0.344,1.938 0.469,2.094 0.125,0.156 10 false 7 0.26,0.646 0.354,0.792 0.094,0.146 10 false 8 2.573,1.854 2.75,2 0.177,0.146 10 false 10 1.865,0.615 2.042,0.76 0.177,0.146 10 true 20 1.521,1.865 1.698,2.01 0.177,0.146 10 true 19 1.521,0.094 1.698,0.24 0.177,0.146 10 false 18 2.354,0.635 2.531,0.781 0.177,0.146 10 true 17 2.021,1.875 2.198,2.021 0.177,0.146 10 true 16 2.01,0.104 2.188,0.25 0.177,0.146 10 false 15 1.344,0.625 1.521,0.771 0.177,0.146 10 true 14 1.01,1.854 1.188,2 0.177,0.146 10 true 13 1.073,0.115 1.25,0.26 0.177,0.146 10 false 12 2.99,0.854 3.167,1 0.177,0.146 10 false 11

Uniformly loosen and remove the 20 bolts in the order shown in the illustration.


b.
A196899

Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 21.REMOVE CAMSHAFT BEARING CAP

a.
A196885
2.125,1.667 2.229,1.813 0.104,0.146 10 true 9 0.313,1.938 0.406,2.094 0.094,0.156 10 true 1 0.125,0.094 0.219,0.271 0.094,0.177 10 false 2 0.083,0.74 0.198,0.885 0.115,0.146 10 false 3 2.677,0.01 2.771,0.167 0.094,0.156 10 false 4 2.708,1.677 2.823,1.823 0.115,0.146 10 true 5 0.969,0.021 1.083,0.177 0.115,0.156 10 false 6 0.917,1.688 1.042,1.844 0.125,0.156 10 false 7 2.094,0 2.188,0.146 0.094,0.146 10 false 8 1.479,0 1.656,0.146 0.177,0.146 10 false 10 1.5,1.688 1.677,1.833 0.177,0.146 10 false 11

Remove the 11 bolts in the order shown in the illustration.


b.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 15678A 22.REMOVE OIL CONTROL VALVE FILTER

Hide 11811 23.REMOVE NO. 1 CAMSHAFT BEARING

Hide 13511 24.REMOVE CAMSHAFT

a.

Remove the camshaft and No. 2 camshaft.


Hide 11821 25.REMOVE NO. 2 CAMSHAFT BEARING

Hide 13801 26.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 16 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 27.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 28.REMOVE VALVE STEM CAP

a.

Remove the 16 valve stem caps from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 11101 29.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A196908
1.479,0.25 1.583,0.396 0.104,0.146 10 false 9 0.563,1.635 0.656,1.792 0.094,0.156 10 true 1 2.406,0.26 2.5,0.438 0.094,0.177 10 false 2 0.615,0.25 0.729,0.396 0.115,0.146 10 false 3 2.427,1.635 2.521,1.792 0.094,0.156 10 false 4 1.031,1.635 1.146,1.781 0.115,0.146 10 true 5 1.948,0.26 2.063,0.417 0.115,0.156 10 false 6 1.042,0.271 1.167,0.427 0.125,0.156 10 false 7 1.958,1.625 2.052,1.771 0.094,0.146 10 false 8 1.458,1.646 1.635,1.792 0.177,0.146 10 false 10

Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 bolts in the order shown in the illustration. Remove the 10 cylinder head bolts and 10 plate washers.

HINT:

Be sure to keep the removed parts separate for each installation position.


NOTICE:
·

Be careful not to drop plate washers into the cylinder head sub-assembly.

·

Cylinder head warpage or cracking may result from removing bolts in the incorrect order.




b.

Remove the cylinder head sub-assembly.


Hide 11115 30.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.