Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109595 ENGINE UNIT A

1AR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE ENGINE COVER JOINT

a.
A196900

Remove the 3 engine cover joints.


Hide 12108 3.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.


b.

Remove the gasket from the oil filler cap sub-assembly.


Hide 11101J 4.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11101J 5.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 11102A 6.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11102A 7.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 12204 8.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 12205 9.REMOVE VENTILATION CASE SUB-ASSEMBLY

a.
A210185
0.26,1.76 0.479,1.958 0.219,0.198 10 true *a 0.208,0.354 0.427,0.552 0.219,0.198 10 true *a 0.781,0.083 1,0.281 0.219,0.198 10 true *a 1.51,0.063 1.729,0.26 0.219,0.198 10 true *a 2.854,0.135 3.073,0.333 0.219,0.198 10 true *a 3.073,0.875 3.292,1.073 0.219,0.198 10 true *a 1.896,1.938 2.115,2.135 0.219,0.198 10 true *a 0.917,1.708 1.135,1.906 0.219,0.198 10 true *a 1.26,1.938 1.479,2.135 0.219,0.198 10 true *b 3.042,1.75 3.26,1.948 0.219,0.198 10 true *b
*a Bolt
*b Nut


Remove the 8 bolts and 2 nuts.


b.
A210186

Remove the ventilation case sub-assembly by prying between the ventilation case sub-assembly and cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and ventilation case sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 12215 10.REMOVE SEPARATOR CASE

a.
A210188

Remove the 2 bolts, separator case and gasket.


Hide 16268 11.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A320286
0.354,1.188 0.552,1.365 0.198,0.177 10 true *a 0.708,0.5 0.906,0.677 0.198,0.177 10 true *a 2,1.781 2.188,1.969 0.188,0.188 10 true *b
*a Nut
*b Bolt


Remove the bolt, 2 nuts and No. 1 water by-pass pipe and gasket.


Hide 16321 12.REMOVE WATER INLET

Hide 16331A 13.REMOVE THERMOSTAT

Hide 16620 14.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A196670

Remove the bolt and V-ribbed belt tensioner assembly.


Hide 16100 15.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 16323 16.REMOVE WATER INLET HOUSING

a.
A195872
1.5,1.979 1.813,2.177 0.313,0.198 10 true *a 1.875,1.125 2.188,1.323 0.313,0.198 10 true *a 1.844,0.135 2.156,0.333 0.313,0.198 10 true *a 2.313,0.094 2.625,0.292 0.313,0.198 10 true *a 3.021,0.74 3.333,0.938 0.313,0.198 10 true *b
*a Bolt
*b Nut


Remove the 4 bolts, nut and water inlet housing and gasket.


Hide 11301K 17.REMOVE CRANKSHAFT POSITION SENSOR

Hide 13470 18.REMOVE CRANKSHAFT PULLEY

a.
A293510
1.323,0.99 0.583,0.865 0.583,0.865 1.219,0.635 true 0.552,0.271 0.865,0.427 0.313,0.156 10 false *a 2.417,1.677 2.729,1.833 0.313,0.156 10 false *b 0.292,0.781 0.969,1 0.677,0.219 10 false SST
*a Hold
*b Turn


Using SST, hold the crankshaft pulley and loosen the crankshaft pulley bolt. Further loosen the crankshaft pulley bolt until 2 or 3 threads are screwed into the crankshaft.

SST
09213-54015  
09330-00021  

HINT:

SST (crankshaft pulley holding tool) fixing bolt part No.: 91551-80650 (2 pcs)



b.
A195874
2.25,0.219 2.542,0.688 false 1.813,0.875 1.469,1.083 false 1.313,1.094 1.729,1.344 0.417,0.25 10 false SST 2.063,0.115 2.281,0.302 0.219,0.188 10 false *1 0.333,1.979 0.615,2.188 0.281,0.208 10 false *a 1.219,3.177 1.49,3.354 0.271,0.177 10 false *b
*1 Crankshaft Pulley Bolt
*a Hold
*b Turn


Using SST and the crankshaft pulley bolt, remove the crankshaft pulley and crankshaft pulley bolt.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05011)

HINT:

Apply lubricant to the threads and end of SST.



Hide 11201 19.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A195876
2.146,1.156 1.979,1.344 1.979,1.344 2.635,1.146 false 1.979,1.354 1.323,1.031 false 1.927,1.385 2.24,1.583 0.313,0.198 10 false *a
*a Seal Washer


Remove the 16 bolts, 3 seal washers and cylinder head cover sub-assembly and cylinder head cover gasket.


b.
A196857

Remove the 3 camshaft bearing cap oil hole gaskets.


Hide 11193 20.REMOVE SPARK PLUG TUBE GASKET

a.
A195877
0.865,1.292 0.99,1.292 0.99,1.292 1.083,0.917 true 0.688,1.208 1,1.406 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, pry out the 4 spark plug tube gaskets.

NOTICE:

Be careful not to damage the cylinder head cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 12315A 21.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11310 22.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 23.REMOVE TIMING CHAIN COVER TIGHT PLUG

a.
A196859

Using a 14 mm hexagon wrench, remove the timing chain cover tight plug and gasket.


Hide 11324 24.REMOVE TIMING CHAIN COVER PLATE

a.
A196860

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 11301C 25.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 26.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13540 28.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 29.REMOVE CHAIN TENSIONER SLIPPER

Hide 13506 30.REMOVE CHAIN SUB-ASSEMBLY

a.

Remove the chain sub-assembly.


Hide 13561 31.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13521 32.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A196881

Remove the crankshaft timing sprocket from the crankshaft.


Hide 13050 33.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 34.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11103 35.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13801 36.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 37.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 15678A 41.REMOVE OIL CONTROL VALVE FILTER

a.
A196915

Remove the oil control valve filter from the No. 1 camshaft bearing cap.


Hide 11811 42.REMOVE NO. 1 CAMSHAFT BEARING

a.
A196916

Remove the No. 1 camshaft bearing from the No. 1 camshaft bearing cap.


Hide 11821 43.REMOVE NO. 2 CAMSHAFT BEARING

a.
A196917

Remove the No. 2 camshaft bearing from the camshaft housing sub-assembly.


Hide 44.REMOVE CAMSHAFT HOUSING STUD BOLT

NOTICE:

If a camshaft housing stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E8 "TORX" socket wrench, remove the stud bolt from the camshaft housing sub-assembly.


Hide 11151A 45.REMOVE CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the camshaft bearing cap setting ring pin unless it is being replaced.


a.

Remove the 10 camshaft bearing cap setting ring pins from the camshaft housing sub-assembly.


Hide 11114A 46.REMOVE CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove the camshaft housing straight pin unless it is being replaced.


a.

Remove the 2 straight pins from the camshaft housing sub-assembly.


Hide 11101 47.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11445 49.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A196938

Remove the cylinder block water jacket spacer from the cylinder block sub-assembly.

NOTICE:

Be sure to remove the cylinder block water jacket spacer. If it is not removed, it may fall and become damaged when the cylinder block sub-assembly is inverted.



Hide 15620 50.REMOVE OIL FILTER CAP ASSEMBLY

Hide 12101A 51.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket from the oil pan sub-assembly.


Hide 12101 52.REMOVE OIL PAN SUB-ASSEMBLY

a.
A210204
0.771,1.219 1.781,1.396 1.781,1.396 1.5,1.854 false 1.823,1.323 2.063,1.469 0.24,0.146 10 false *a
*a Nut


Remove the 11 bolts and 2 nuts.


b.
A118769

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and stiffening crankcase assembly, cut through the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the stiffening crankcase assembly contact surface of the oil pan sub-assembly.

·

Be careful not to damage the stiffening crankcase flange.




Hide 15104 53.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A196919

Remove the 3 bolts, oil strainer sub-assembly and gasket.


Hide 12121 54.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A196920

Remove the 5 bolts and No. 1 oil pan baffle plate.


Hide 13411 55.INSPECT CRANKSHAFT BACKLASH

a.
A196931

Using a dial indicator, measure the backlash of the crankshaft and balance shaft as shown in the illustration.

Standard Backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


Maximum Backlash:

0.20 mm (0.00787 in.)


If the backlash is more than the maximum, replace the engine balancer assembly.


Hide 13620B 56.REMOVE ENGINE BALANCER ASSEMBLY

a.
A196921

Remove the 7 bolts and engine balancer assembly.

NOTICE:

Do not disassemble the engine balancer assembly.



Hide 57.INSPECT NO. 1 BALANCE SHAFT THRUST CLEARANCE

Hide 58.INSPECT NO. 2 BALANCE SHAFT THRUST CLEARANCE

Hide 11420 59.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A196933

Remove the 7 bolts.


b.
A196934
0.036,0.0 0.208,0.157 0.172,0.157 10 *a 0.036,2.131 0.2,2.308 0.164,0.177 10 *b
*a LH Side
*b RH Side


Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block sub-assembly at the places shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and stiffening crankcase assembly.


HINT:

Tape the screwdriver tip before use.



Hide 60.REMOVE STIFFENING CRANKCASE STUD BOLT

NOTICE:

If a stiffening crankcase stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E5 and E8 "TORX" socket wrench, remove the 3 stud bolts from the stiffening crankcase assembly.


Hide 61.REMOVE STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove the stiffening crankcase ring pin unless it is being replaced.


a.

Remove the 2 ring pins from the stiffening crankcase assembly.


Hide 11401L 62.REMOVE REAR ENGINE OIL SEAL

a.
A196937

Remove the rear engine oil seal from the cylinder block sub-assembly.