Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2015.11
RM3160E _59 Vehicle Exterior _019719 DOOR / HATCH _0108187 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67492A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B360759

Disengage the 2 clips and guide and remove the front door lower frame bracket garnish.


Hide 69284C 4.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B360760

Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug.


Hide 5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

a.
B360762

Using a moulding remover, disengage the 2 clips, 4 claws and 2 guides.


b.

Disconnect each connector and remove the power window regulator master switch assembly with front door upper armrest base panel.


Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

a.
B360768

Using a moulding remover, disengage the 2 clips, 4 claws and 2 guides.


b.

Disconnect each connector and remove the power window regulator switch assembly with front door upper armrest base panel.


Hide 81230N 7.REMOVE COURTESY LIGHT ASSEMBLY

Hide 67602 8.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B360770C01
0,0 0,0 false
V100155

Protective Tape


Put protective tape around the front door panel.


b.
B360771C01
2.385,1.552 2.052,1.156 true 2.365,1.583 2.677,1.74 0.313,0.156 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the claw and open the cover.


c.
B360773

Remove the 3 screws.


d.
B360774

Disengage the 10 clips and remove the front door trim board sub-assembly as shown in the illustration.


e.

w/ Memory:

i.

Disconnect the connector.



f.

w/ Illumination:

i.

Disconnect the connector.



g.
B360776

Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.


Hide 69206B 9.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B360778

Disengage the 2 claws and guide, and remove the front door inside handle sub-assembly.


Hide 68172A 10.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

a.
B360779

Disengage the 7 claws and remove the front door inner glass weatherstrip as shown in the illustration.


Hide 84927C 11.REMOVE SEAT MEMORY SWITCH (w/ Memory)

Hide 89430 12.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)

Hide 13.REMOVE OUTER REAR VIEW MIRROR WITH COVER

Hide 86160 14.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 67832 15.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B360782

Remove the front door service hole cover.

HINT:

Remove any remaining butyl tape from the front door panel.



Hide 68102 16.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

a.
B360784

Remove the grommet.


b.

Connect the cable to the negative (-) battery terminal.


c.

for Driver Side:

i.

Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


ii.

Disconnect the power window regulator master switch assembly.



d.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


ii.

Disconnect the power window regulator switch assembly.



e.

Disconnect the cable from the negative (-) battery terminal.


f.

Disconnect the power window regulator master switch assembly.


g.
B360785

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the front door glass sub-assembly to fall.



h.
B360786N01
0.167,0.427 0.323,0.625 0.156,0.198 10 false 1 1.552,0.229 1.708,0.427 0.156,0.198 10 false 2

Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly.



Hide 17.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.
B360788C01
1.865,0.469 2.177,0.74 true 1.708,0.365 1.938,0.531 0.229,0.167 10 true *a
*a Temporary Bolt


Disconnect the connector.


b.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.



c.

Remove the 5 bolts.


d.

Remove the front door window regulator assembly.


e.

Remove the temporary bolt from the front door window regulator assembly.


Hide 85720D 18.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B360790

Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.


Hide 68151D 19.REMOVE FRONT DOOR GLASS RUN

a.
B360791

Remove the front door glass run.


Hide 67402F 20.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B360793

Remove the 2 bolts and disconnect wire harness.


b.
B360794

Remove the 2 bolts.


c.

Disengage the guide and remove the front door front lower frame sub-assembly.


Hide 67404F 21.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B360792

Remove the bolt.


b.

Disengage the guide and remove the front door rear lower frame sub-assembly.


Hide 22.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B360795

Remove the hole plug.


b.
B360799

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69217D 23.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B360797

Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration.


Hide 69217D 24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B360796

Remove the hole plug.


b.
B360800

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69220 25.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.

w/ Smart Entry and Start System:

i.
B360801

Disengage the 2 claws.


ii.

Using a screwdriver, disconnect the connector.



b.
B360803

Remove the front door outside handle assembly as shown in the illustration.


Hide 69241H 26.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B360805

Disengage the 3 claws and remove the front door front outside handle pad.


Hide 69242E 27.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B360806

Disengage the 2 claws and remove the front door rear outside handle pad.


Hide 69040A 28.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

a.
B360808C01
3.083,2.75 3,2.594 true 3.01,2.781 3.271,2.99 0.26,0.208 10 true *1
*1 Front Door Lock Open Rod


Disconnect the connector.


b.

Using a T30 "TORX" socket wrench, remove the 3 screws.


c.

Slide the front door lock with motor assembly downward to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.


d.

When reusing the front door lock with motor assembly:

i.
B360815

Remove the door lock wiring harness seal from the front door lock with motor assembly.



Hide 69720B 29.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B360809

Using a screwdriver, disengage the 2 claws as shown in the illustration.


b.
B360811

Remove the front door lock remote control cable assembly as shown in the illustration.


Hide 69760C 30.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B360813

Remove the front door inside locking cable assembly as shown in the illustration.


Hide 69202A 31.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

w/ Smart Entry and Start System:

i.
B360816

Disengage the 3 clamps.



b.
B362049C01
0.083,0.083 0.417,0.313 0.333,0.229 12 false *A 0.104,2.25 0.417,2.479 0.313,0.229 12 false *B
*A Inside
*B Outside


Using a T30 "TORX" socket wrench, loosen the screw.


c.

Slide the front door outside handle frame sub-assembly to disengage the claw, and then remove it.


Hide 69312 32.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B362051N01
1.938,0.531 2.094,0.729 0.156,0.198 10 true 1 3.021,0.677 3.177,0.875 0.156,0.198 10 false 2

Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 68620 33.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B362053C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, 2 nuts and front door check assembly.


Hide 67862 34.REMOVE FRONT DOOR WEATHERSTRIP

a.
B362054

Using a clip remover, disengage the 20 clips and remove the front door weatherstrip.


Hide 67924 35.REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION

a.
B362055C01
0,0 0,0 false
V100155

Double-sided Tape


Remove the 2 bolts.


b.

Disengage the 2 guides and remove the front door No. 2 stiffener cushion.


Hide 67663D 36.REMOVE DOOR FRAME GARNISH

a.
B362056

Disengage the 3 claws and remove the door frame garnish.


Hide 67001A 37.REMOVE FRONT DOOR PANEL CUSHION

a.
B362057

Disengage the 2 claws and remove the 2 front door panel cushions.


Hide 67856D 38.REMOVE FRONT DOOR PANEL PROTECTOR

a.
B433233N01
2.615,0.219 2.771,0.417 0.156,0.198 10 true A 2.688,1.26 2.844,1.458 0.156,0.198 10 true A 0.813,2.135 1.271,2.333 0.458,0.198 10 false A-A

Remove the front door panel protector.


Hide 67838A 39.REMOVE FRONT DOOR VENT SEAL

a.
B433234N01
1.5,1.063 1.656,1.26 0.156,0.198 10 true A 1.563,1.75 1.719,1.948 0.156,0.198 10 true A 0.219,2.271 0.677,2.469 0.458,0.198 10 false A-A

Remove the front door vent seal.


Hide 75720 40.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Hide 75756C 41.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

Hide 75754A 42.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 75939 43.REMOVE FRONT DOOR UPPER INNER BLACK OUT TAPE

Hide 75969 44.REMOVE FRONT DOOR REAR INNER BLACK OUT TAPE

Hide 45.REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 75793 46.REMOVE FRONT DOOR UPPER OUTSIDE MOULDING PAD