11310
1.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
| *1 | Oil Pump Gasket |
| *2 | Oil Hole Cover Gasket |
Apply a light coat of engine oil to 2 new oil pump gaskets and a new oil hole cover gasket.
Install the 2 oil pump gaskets and oil hole cover gasket to the stiffening crankcase assembly.
| *1 | Drive Rotor Spline |
| *2 | Crankshaft Timing Sprocket |
Align the drive rotor spline and the crankshaft timing sprocket as shown in the illustration.
Apply seal packing in a line to the timing chain cover sub-assembly as shown in the following illustration.
| *a | 3.0 mm or more | *b | 7.0 mm or more |
| *c | 13.0 mm or more | - | - |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.
| Area | Seal Packing Diameter (Round) | Distance from Edge of Cover to Center of Seal Packing | Seal Packing Application Length |
|---|---|---|---|
| Seal Packing Dimension (Flat) | |||
| Dashed Line | 2.5 to 3.5 mm (0.0984 to 0.0138 in.) | 2.5 mm (0.0984 in.) | - |
| - | |||
| A - A | 2.5 to 3.5 mm (0.0984 to 0.0138 in.) | 2.5 mm (0.0984 in.) | - |
| - | |||
| B - B | 5.0 mm (0.197 in.) | 3.0 mm (0.118 in.) | 28 mm (1.10 in.) |
| 7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker | |||
| C - C | 7.0 mm (0.276 in.) | 5.0 mm (0.197 in.) | 25 mm (0.984 in.) |
| 13.0 mm (0.512 in.) or wider and 3.0 mm (0.118 in.) or thicker | |||
| D - D | 5.0 mm (0.197 in.) | 3.0 mm (0.118 in.) | 26 mm (1.02 in.) |
| 7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker | |||
| E | 2.5 to 3.5 mm (0.0984 to 0.0138 in.) | 3.0 mm (0.118 in.) | - |
| - |
Clean the surfaces with non-residue solvent before applying seal packing.
Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.
Do not add oil for at least 2 hours after installation.
Do not start the engine for at least 2 hours after installation.
Temporarily install the timing chain cover sub-assembly with the 17 bolts and 2 nuts.
| *1 | Nut | - | - |
| *a | Torque | *b | Tightening Order |
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt (A) | 30 mm (1.18 in.) | 8 mm (0.315 in.) |
| Bolt (B) | 35 mm (1.38 in.) | 10 mm (0.394 in.) |
| Bolt (C) | 45 mm (1.77 in.) | 8 mm (0.315 in.) |
Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.
Tighten the 17 bolts and 2 nuts in several steps, in the order shown in the illustration.
12315A
2.INSTALL ENGINE MOUNTING BRACKET RH
Install the engine mounting bracket RH with the 5 bolts in the order shown in the illustration.
After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.
11301C
3.INSTALL TIMING CHAIN COVER OIL SEAL
13470
4.INSTALL CRANKSHAFT PULLEY
11102A
5.INSTALL CRANKSHAFT POSITION SENSOR
16620
6.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
11201
7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
19500
8.INSTALL IGNITION COIL ASSEMBLY
9.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE