Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › ENGINE UNIT › from 2015.11
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109595 ENGINE UNIT A

1AR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Install the rear engine oil seal from the cylinder block sub-assembly.


Hide 2.INSTALL STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove the stiffening crankcase ring pin unless it is being replaced.


a.
A198197C10
2.374,2.431 2.555,2.586 0.181,0.155 10 *a
*a Protrusion Height


Using a plastic hammer, tap in 2 new stiffening crankcase ring pins until they stop.

Standard Protrusion Height:

4.3 to 5.3 mm (0.169 to 0.209 in.)



Hide 13620B 3.INSTALL ENGINE BALANCER ASSEMBLY

a.
A198170C12
2.188,0.99 1.521,0.698 1.521,0.698 2.188,1.104 true 1.323,0.615 1.479,0.76 0.156,0.146 10 true *a
*a Alignment Mark


Check that the alignment marks of the balance shaft damper cover and No. 1 balance shaft driven gear are aligned.

If the alignment marks are not aligned, align them.

i.
A198171C11
1.208,0.885 1.323,0.885 1.323,0.885 1.583,1.25 true 2.208,1.292 2.615,1.646 2.615,1.646 2.292,1.167 true 1.302,1.573 1.688,1.563 true 1,0.792 1.188,0.948 0.188,0.156 10 true *1 1.104,1.479 1.292,1.656 0.188,0.177 10 true *2 2.573,1.667 2.771,1.844 0.198,0.177 10 true *a
*1 No. 1 Balance Shaft Driven Gear
*2 Balance Shaft Damper Cover
*a Alignment Mark


Place a wrench on the rear cutout part of the No. 2 balance shaft and secure the No. 2 balance shaft in place.


ii.

Rotate the balance shaft driven gear of the No. 1 balance shaft counterclockwise to align the alignment mark of the No. 1 balance shaft driven gear with the alignment mark of the balance shaft damper cover.



b.
A196927N08
1.021,1.365 1.115,1.521 0.094,0.156 10 true 1 2.667,0.167 2.76,0.344 0.094,0.177 10 true 2 2.781,1.667 2.896,1.813 0.115,0.146 10 true 3

Install the engine balancer assembly to the stiffening crankcase assembly with the 3 bolts, and tighten the bolts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 4.INSTALL STIFFENING CRANKCASE STUD BOLT

NOTICE:

If a stiffening crankcase stud bolt is deformed or its threads are damaged, replace it.


a.

Using E5 and E8 "TORX" socket wrenches, install the stiffening crankcase stud bolts.

A198166C08
5.063,0.385 4.76,0.74 false 5.146,1.802 4.76,2.083 false 5.104,1.417 4.76,1.146 false 5.156,2.615 4.76,2.375 false 5.198,1.719 6.427,1.917 1.229,0.198 10 false 8.5 mm (0.335 in.) 5.229,2.563 6.49,2.771 1.26,0.208 10 false 8.0 mm (0.315 in.) 5.385,2.167 6.583,2.354 1.198,0.188 10 false 18 mm (0.709 in.) 2.26,1.063 2.375,1.219 0.115,0.156 10 false A 4.146,0.115 4.26,0.271 0.115,0.156 10 false A 1.063,1.875 1.208,2.021 0.146,0.146 10 false B 1.625,2.271 1.729,2.427 0.104,0.156 10 true B 4.156,1.646 4.302,1.792 0.146,0.146 10 false B 5.135,1.344 6.281,1.573 1.146,0.229 10 false 13 mm (0.512 in.) 5.115,0.26 6.26,0.5 1.146,0.24 10 false 20 mm (0.787 in.) 5.365,0.813 6.531,1.021 1.167,0.208 10 false 35 mm (1.38 in.) 0.208,0 0.396,0.167 0.188,0.167 10 false *a 0.208,1.302 0.396,1.49 0.188,0.188 10 false *b
*a Front Side *b Lower Side


Torque:
Stud Bolt (A) : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
Stud Bolt (B) : 4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 11420 5.INSTALL STIFFENING CRANKCASE ASSEMBLY

a.
A198168C09
0.771,0.646 1.521,1.073 false 0.583,0.552 0.75,0.74 0.167,0.188 10 false *1 1.156,1.49 1.396,1.656 0.24,0.167 10 true 90°
*1 Crankshaft Pulley Key


Rotate the crankshaft clockwise so that the crankshaft pulley key is at the position 90° from the bottom as shown in the illustration.


b.
A258254C09
2.115,0.969 1.771,0.271 1.771,0.271 1.667,0.271 false 0.75,0.156 1.677,0.365 0.927,0.208 10 false 2.5 to 3.5 mm 3.01,0.49 3.146,0.656 0.135,0.167 10 false A 1.146,3.521 1.281,3.688 0.135,0.167 10 false A 0.313,4.083 1.219,4.25 0.906,0.167 10 false 2.5 to 3.5 mm 2.104,3.688 3.021,3.865 0.917,0.177 10 false 7.0 to 9.0 mm
V100145

Stiffening Crankcase Assembly
V100146

Cylinder Block Sub-assembly


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Dimension:
Area Specified Condition
Continuous Line 2.5 to 3.5 mm (0.0984 to 0.138 in.)
Dashed Line 7.0 to 9.0 mm (0.276 to 0.354 in.) wide and 2.5 to 3.5 mm (0.0984 to 0.138 in.) thick


Application Length (A):

28 mm (1.10 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 15 minutes of applying seal packing.

·

Do not apply oil for at least 2 hours after the installation.




c.
A285537C07
1.417,0.979 1.208,0.302 1.208,0.302 1.99,0.99 false 1.083,0.125 1.396,0.281 0.313,0.156 10 *a
*a Cutout


Check that the rear cutouts are as shown in the illustration.


d.

Clean the bolts and the bolt holes.


e.
A198186C09
1.74,0.552 2.083,0.833 false 1.542,0.469 1.708,0.646 0.167,0.177 10 false *a
*a Adhesive


Apply adhesive to 3 or more threads at the tip of the bolts (A).

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



f.
A198172N07
0.677,0.281 0.792,0.438 0.115,0.156 10 false A 0.938,1.948 1.052,2.104 0.115,0.156 10 false A 2.781,0.052 2.927,0.198 0.146,0.146 10 false B 2.99,1.865 3.135,2.01 0.146,0.146 10 false B 2.865,0.906 3.01,1.052 0.146,0.146 10 false C 2.573,1.927 2.719,2.073 0.146,0.146 10 false C 2.854,1.083 3,1.229 0.146,0.146 10 false C 2.365,0.052 2.51,0.208 0.146,0.156 10 false D 2.26,0.958 2.406,1.115 0.146,0.156 10 true D 1.271,1.969 1.417,2.125 0.146,0.156 10 true D 1.292,0.031 1.438,0.188 0.146,0.156 10 true D

Temporarily install the stiffening crankcase assembly with the 11 bolts.

Bolt Length :
Item Length
Bolt (A) 65 mm (2.56 in.)
Bolt (B) 35 mm (1.38 in.)
Bolt (C) 125 mm (4.92 in.)
Bolt (D) 165 mm (6.50 in.)


HINT:

Apply adhesive to the bolts (A) before installation.



g.
A198172N08
2.844,1.063 2.948,1.208 0.104,0.146 10 true 9 2.51,1.958 2.604,2.115 0.094,0.156 10 false 1 2.323,0.042 2.417,0.219 0.094,0.177 10 false 2 2.219,0.979 2.333,1.125 0.115,0.146 10 true 3 2.729,0 2.823,0.156 0.094,0.156 10 false 4 2.938,1.865 3.052,2.01 0.115,0.146 10 false 5 1.271,0.052 1.385,0.208 0.115,0.156 10 true 6 1.292,1.979 1.417,2.135 0.125,0.156 10 true 7 2.844,0.885 2.938,1.031 0.094,0.146 10 false 8 0.604,0.25 0.781,0.396 0.177,0.146 10 false 10 0.875,1.927 1.052,2.073 0.177,0.146 10 false 11

Tighten the 11 bolts in the order shown in the illustration to install the stiffening crankcase assembly.

Torque:
Bolt (A) : 24 N*m (245 kgf*cm, 18 ft.*lbf)
except Bolt (A) : 43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 12121 6.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.
A196920N04
1.177,0.51 1.271,0.667 0.094,0.156 10 true 1 2.083,1.948 2.177,2.125 0.094,0.177 10 false 2 0.625,0.802 0.74,0.948 0.115,0.146 10 true 3 1.49,1.906 1.583,2.063 0.094,0.156 10 true 4 1.24,0.188 1.354,0.333 0.115,0.146 10 true 5

Install the No. 1 oil pan baffle plate and uniformly tighten the 5 bolts in several steps, in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15104 7.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new gasket.


b.
A198187C04
1.635,0.365 2.115,0.625 false 1.417,0.25 1.594,0.438 0.177,0.188 10 false *a 0.573,1.927 0.708,2.083 0.135,0.156 10 true 1 0.646,3.052 0.74,3.229 0.094,0.177 10 true 2 2.146,2.99 2.26,3.135 0.115,0.146 10 true 3
*a Protrusion


Align the protrusion of the gasket with the cutout of the oil strainer sub-assembly, and install the gasket to the oil strainer sub-assembly.


c.

Install the oil strainer sub-assembly with the 3 bolts in several steps, in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12101 8.INSTALL OIL PAN SUB-ASSEMBLY

a.
A210205E01
0.446,1.562 1.347,1.722 0.901,0.161 10 2.5 to 3.5 mm 1.525,1.657 1.864,1.657 false

Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.
A210204C14
0.781,1.208 1.823,1.375 1.823,1.375 1.5,1.823 true 1.854,1.302 2.031,1.448 0.177,0.146 10 false *a 2.042,0 2.313,0.156 0.271,0.156 10 false 1, 9 1.104,2 1.469,2.156 0.365,0.156 10 false 2, 15 0.823,1.938 0.938,2.083 0.115,0.146 10 false 3 0.427,1.625 0.521,1.781 0.094,0.156 10 false 4 0.385,1.01 0.5,1.156 0.115,0.146 10 false 5 0.74,0.594 0.854,0.75 0.115,0.156 10 true 6 1.021,0.417 1.146,0.573 0.125,0.156 10 false 7 1.146,0.063 1.24,0.208 0.094,0.146 10 false 8 2.365,0.292 2.542,0.438 0.177,0.146 10 false 10 2.052,1.938 2.229,2.083 0.177,0.146 10 false 14 2.521,1.719 2.698,1.865 0.177,0.146 10 true 13 2.646,1.146 2.823,1.292 0.177,0.146 10 true 12 2.667,0.729 2.844,0.875 0.177,0.146 10 true 11 1.615,1.802 1.729,1.958 0.115,0.156 10 true A 1.729,0.365 1.844,0.521 0.115,0.156 10 true A
*a Nut


Install the oil pan sub-assembly with the 11 bolts and 2 nuts in several steps, in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

The bolt (A) and nut (A) are tightened twice.



Hide 12101A 9.INSTALL OIL PAN DRAIN PLUG

a.

Install a new gasket and the oil pan drain plug to the oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15620 10.INSTALL OIL FILTER CAP ASSEMBLY

Hide 11445 12.INSTALL CYLINDER BLOCK WATER JACKET SPACER

a.
A196938

Install the cylinder block water jacket spacer to the cylinder block sub-assembly.


Hide 11101 14.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 11151A 16.INSTALL CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the camshaft bearing cap setting ring pin unless it is being replaced.


a.
A198195C12
2.422,1.604 2.595,1.757 0.172,0.152 10 *a
*a Protrusion Height


Using a plastic hammer, tap in 10 new camshaft bearing cap setting ring pins to the camshaft housing sub-assembly.

Standard Protrusion Height:

2.7 to 3.3 mm (0.106 to 0.130 in.)



Hide 11114A 17.INSTALL CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove the camshaft housing straight pin unless it is being replaced.


a.
A198194C10
2.109,1.583 2.27,1.739 0.162,0.156 10 *a
*a Protrusion Height


Using a plastic hammer, tap in 2 new camshaft housing straight pins to the camshaft housing sub-assembly.

Standard Protrusion Height:

5.0 to 7.0 mm (0.197 to 0.276 in.)



Hide 18.INSTALL CAMSHAFT HOUSING STUD BOLT

NOTICE:

If a camshaft housing stud bolt is deformed or its threads are damaged, replace it.


a.
A198196N07
1.875,1.688 1.75,1.688 1.75,1.688 1.531,2.271 false 1.531,2.802 1.896,3.25 1.896,3.25 2.125,3.25 false 2.167,3.167 3.313,3.396 1.146,0.229 10 false 13 mm (0.512 in.) 1.948,1.594 3.094,1.833 1.146,0.24 10 false 20 mm (0.787 in.) 2.25,2.375 3.375,2.573 1.125,0.198 10 false 35 mm (1.38 in.)

Using an E8 "TORX" socket wrench, install the camshaft housing stud bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 11811 19.INSTALL NO. 1 CAMSHAFT BEARING

a.
A243410C06
2.333,2.563 2.01,2.563 2.01,2.563 1.802,2.25 false 2.365,2.479 2.552,2.635 0.188,0.156 10 false *a 0.146,2.365 0.26,2.51 0.115,0.146 10 false A 1.635,2.365 1.75,2.51 0.115,0.146 10 false B
*a Vernier Caliper


Clean the No. 1 camshaft bearing.


b.

Install the No. 1 camshaft bearing to the No. 1 camshaft bearing cap.


c.

Using a vernier caliper, measure the distance between the No. 1 camshaft bearing cap edge and the No. 1 camshaft bearing edge.

Difference Between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)



Hide 11821 20.INSTALL NO. 2 CAMSHAFT BEARING

a.

Clean the No. 2 camshaft bearing.


b.

Install the No. 2 camshaft bearing to the camshaft housing sub-assembly.


c.
A198177C15
0.917,1.313 0.823,1.313 0.823,1.313 0.74,2.531 false 0.969,1.229 1.156,1.417 0.188,0.188 10 false *a
*a Vernier Caliper


Using a vernier caliper, measure the distance between the camshaft housing sub-assembly edge and the No. 2 camshaft bearing edge.

Standard Distance:

1.15 to 1.85 mm (0.0453 to 0.0728 in.)



Hide 15678A 21.INSTALL OIL CONTROL VALVE FILTER

a.
A196915

Install the oil control valve filter to the No. 1 camshaft bearing cap.


Hide 13750 25.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 26.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11103 27.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13050 28.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 29.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13521 30.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A196881

Install the crankshaft timing sprocket to the crankshaft.


Hide 13561 33.INSTALL NO. 1 CHAIN VIBRATION DAMPER

Hide 13540 36.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11324 39.INSTALL TIMING CHAIN COVER PLATE

a.
A196860

Install a new gasket and the timing chain cover plate with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 40.INSTALL TIMING CHAIN COVER TIGHT PLUG

a.
A196859

Using a 14 mm hexagon wrench, install a new gasket and the timing chain cover tight plug.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 11310 41.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 12315A 42.INSTALL ENGINE MOUNTING BRACKET RH

Hide 11193 44.INSTALL SPARK PLUG TUBE GASKET

a.
A196890

Tap in 4 new spark plug tube gaskets to the cylinder head cover sub-assembly.

NOTICE:

After tapping in the spark plug tube gaskets, make sure each gasket protrudes 1.0 mm (0.0394 in.) or less from the cylinder head cover sub-assembly.



Hide 11201 45.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A196857

Apply a light coat of engine oil to 3 new camshaft bearing cap oil hole gaskets.


b.

Install the camshaft bearing cap oil hole gaskets.


c.

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

NOTICE:

Remove any oil from the contact surface.



d.
A308929C03
0.813,2.49 0.99,2.49 0.99,2.49 1.25,2.76 false 2.219,2.771 2.417,3.031 2.417,3.031 2.604,3.031 false 0.635,2.417 0.948,2.615 0.313,0.198 10 false *1 1.479,3.135 1.792,3.333 0.313,0.198 10 false *a 2.656,2.958 2.969,3.156 0.313,0.198 10 false *2 1.781,3.135 2.094,3.333 0.313,0.198 10 false *a 2.365,2.604 3.292,2.76 0.927,0.156 10 false 3.0 to 6.0 mm
*1 Timing Chain Cover Sub-assembly
*2 Camshaft Housing Sub-assembly
*a Application Width 5.0 mm (0.197 in.)
V100135

Seal Packing


Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

3.0 to 6.0 mm (0.118 to 0.236 in.)


Application Width:

5.0 mm (0.197 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.




e.
A293102C02
0.531,0.177 0.615,0.177 0.615,0.177 0.688,0.469 false 3.042,1.365 3.125,1.292 3.125,1.292 3.198,1.292 false 2.646,1.146 1.99,1.365 1.99,1.365 1.313,1.042 false 2,1.365 2.167,1.146 false 1.688,0.75 2.01,0.906 0.323,0.156 10 true 1, 19 2.844,0.781 3.365,0.969 0.521,0.188 10 false 3, 21 1.677,0.115 2.198,0.302 0.521,0.188 10 false 4, 12 1.479,1.969 2,2.156 0.521,0.188 10 false 5, 18 0.74,0.76 1.073,0.917 0.333,0.156 10 true 2, 20 0.25,0.24 0.406,0.438 0.156,0.198 10 false 9 0.229,1.833 0.385,2.031 0.156,0.198 10 false 7 1.115,1.969 1.271,2.167 0.156,0.198 10 false 6 3.208,1.771 3.427,1.979 0.219,0.208 10 false 16 2.177,1.979 2.49,2.177 0.313,0.198 10 false 17 3.219,0.875 3.427,1.083 0.208,0.208 10 false 15 3.063,0.281 3.344,0.5 0.281,0.219 10 false 14 2.198,0.104 2.469,0.323 0.271,0.219 10 false 13 1.292,0.125 1.573,0.313 0.281,0.188 10 false 11 0.76,0.073 1,0.281 0.24,0.208 10 false 10 0.396,0.104 0.552,0.302 0.156,0.198 10 false A 3.25,1.208 3.406,1.406 0.156,0.198 10 false B 0.094,0.979 0.25,1.177 0.156,0.198 10 false 8 1.927,1.396 2.24,1.594 0.313,0.198 10 false *a
*a Seal Washer


Align the cylinder head cover sub-assembly with the pin (A). Then align the cylinder head cover sub-assembly with the pin (B) and install the cylinder head cover sub-assembly.


f.

Install 3 new seal washers and the 16 bolts, and then tighten the bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after installation.



Hide 13470 46.INSTALL CRANKSHAFT PULLEY

a.
A305738C04
1.313,0.927 0.875,0.875 0.875,0.875 1.198,0.635 true 0.833,0.208 1.146,0.365 0.313,0.156 10 false *a 2.26,1.688 2.573,1.844 0.313,0.156 10 false *b 0.542,0.802 1,1 0.458,0.198 10 false SST
*a Hold
*b Turn


Align the crankshaft pulley key with the key groove of the crankshaft pulley.


b.

Using SST, hold the crankshaft pulley and install the crankshaft pulley bolt.

SST
09213-54015  
09330-00021  

HINT:

SST (crankshaft pulley holding tool) fixing bolt part No.: 91551-80650 (2 pcs)


Torque:
260 N*m (2651 kgf*cm, 192 ft.*lbf)


Hide 11301K 47.INSTALL CRANKSHAFT POSITION SENSOR

Hide 16323 48.INSTALL WATER INLET HOUSING

a.

Install a new gasket and the water inlet housing with the 4 bolts and nut.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16100 49.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 16620 50.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.
A196670

Install the V-ribbed belt tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16331A 51.INSTALL THERMOSTAT

Hide 16321 52.INSTALL WATER INLET

Hide 16268 53.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install a new gasket and the No. 1 water by-pass pipe with the 2 nuts and bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12215 54.INSTALL SEPARATOR CASE

a.
A210188

Apply a light coat of engine oil to a new gasket.


b.

Install the gasket to the separator case.


c.

Install the separator case to the ventilation case sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12205 55.INSTALL VENTILATION CASE SUB-ASSEMBLY

a.
A210187E01
1.394,1.795 2.297,1.951 0.903,0.156 10 2.5 to 3.5 mm 1.364,1.887 1.248,1.887 1.248,1.887 1.035,1.603 false

Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the ventilation case sub-assembly within 3 minutes and tighten the bolts and nuts within 15 minutes of applying seal packing.




b.
A210185N03
0.49,1.323 0.583,1.323 0.583,1.323 0.792,1.427 true 2.719,0.573 2.531,0.573 true 0.896,0 1.094,0.167 0.198,0.167 10 false 10 1.542,0.031 1.719,0.198 0.177,0.167 10 true 11 2.813,0.094 3.135,0.25 0.323,0.156 10 true 2, 12 0.198,1.708 0.469,1.875 0.271,0.167 10 true 1, 8 3.052,0.906 3.156,1.073 0.104,0.167 10 true 3 2.938,1.708 3.052,1.896 0.115,0.188 10 true 4 1.917,1.927 2.021,2.094 0.104,0.167 10 true 5 0.365,0.281 0.563,0.458 0.198,0.177 10 true 9 1.021,1.667 1.125,1.833 0.104,0.167 10 true 7 1.271,1.927 1.375,2.094 0.104,0.167 10 true 6 2.76,0.49 2.885,0.656 0.125,0.167 10 true A 0.365,1.25 0.49,1.417 0.125,0.167 10 true A

Install the ventilation case sub-assembly, and install the 8 bolts and 2 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

The bolt (A) is tightened twice.



Hide 12204 56.INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 11102A 57.INSTALL CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 58.INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11101J 59.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 11101J 60.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 12108 61.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install a new gasket to the oil filler cap sub-assembly.


b.

Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.


Hide 63.INSTALL ENGINE COVER JOINT

a.
A196900

Install the 3 engine cover joints.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)