51100G
1.REMOVE FRONT FRAME ASSEMBLY
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
12361
2.REMOVE FRONT ENGINE MOUNTING INSULATOR (for 1AR-FE)
12360
3.REMOVE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY (for 2GR-FKS)
12372A
4.REMOVE ENGINE MOUNTING INSULATOR LH
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
12362
5.REMOVE ENGINE MOUNTING INSULATOR RH
for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
12380
6.REMOVE REAR ENGINE MOUNTING INSULATOR ASSEMBLY (for 2GR-FKS)
48829A
7.REMOVE FRONT NO. 1 STABILIZER BRACKET LH
48824A
8.REMOVE FRONT NO. 1 STABILIZER BRACKET RH
Perform the same procedure as for the LH side.
48811
9.REMOVE FRONT STABILIZER BAR
Remove the front stabilizer bar with 2 front No. 2 stabilizer brackets, 2 front No. 1 stabilizer bar bushings and 2 front stabilizer link assemblies from the front frame assembly.
10.REMOVE STEERING LINK ASSEMBLY
48069
11.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
48068
12.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
51227B
13.REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER (for 1AR-FE)
Remove the 2 bolts and front suspension member dynamic damper from the front frame assembly.
51229B
14.REMOVE NO. 2 FRAME CROSSMEMBER DYNAMIC DAMPER (for 2GR-FKS)
for 2WD:
Remove the 2 bolts and No. 2 frame crossmember dynamic damper from the front frame assembly.
for AWD:
Remove the 2 bolts and No. 2 frame crossmember dynamic damper from the front frame assembly.
52213A
15.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER
Remove the 2 front suspension member body mounting front stoppers from the front frame assembly.
52216B
16.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER
Remove the 2 front suspension member body mounting rear stoppers from the front frame assembly.
52211J
17.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION
| *1 | Front Suspension Member Body Mounting Front Cushion |
Install SST as shown in the illustration.
| *a | Turn |
| *b | Hold |
Using SST, remove each front suspension member body mounting front cushion from the front frame assembly.
Make sure that the claws of SST are securely engaged to the mounting cushion.
Tighten SST slowly and evenly.
Be careful as the mounting cushion may fly out.
The mounting cushion cannot be reused.
52217E
18.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH
| *1 | Front Suspension Member Body Mounting Rear Cushion LH |
Install SST as shown in the illustration.
| *a | Turn |
| *b | Hold |
Using SST, remove the front suspension member body mounting rear cushion LH from the front frame assembly.
Make sure that the claws of SST are securely engaged to the mounting cushion.
Tighten SST slowly and evenly.
Be careful as the mounting cushion may fly out.
The mounting cushion cannot be reused.
52215
19.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH
Perform the same procedure as for the LH side.
20.REMOVE HOLE PLUG
for 1AR-FE:
Remove the 14 hole plugs from the front frame assembly.
There are 4 different shapes of hole plug.
for 2GR-FKS:
Remove the 10 hole plugs from the front frame assembly.
There are 2 different shapes of hole plug.