Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2016.11
RM3160E _55 Steering _019697 POWER ASSIST SYSTEMS _0104490 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the EPS warning light.

WIRING DIAGRAM

C349029E02
1.375,0.5 1.688,0.698 0.313,0.198 10 false 26 1.375,1.198 1.688,1.396 0.313,0.198 10 false 13 0.917,0.677 1.469,0.885 0.552,0.208 10 false CANL 0.896,1.396 1.51,1.594 0.615,0.198 10 false CANH 5.698,0.5 6.01,0.698 0.313,0.198 10 false 8 5.708,1.167 6.021,1.365 0.313,0.198 10 false 4 5.948,0.667 6.427,0.865 0.479,0.198 10 false CANL 5.615,1.844 5.927,2.042 0.313,0.198 10 false p1 5.833,1.844 6.813,2.302 0.979,0.458 10 false Power Steering ECU Assembly 1.094,2.948 1.406,3.146 0.313,0.198 10 false TC 1.375,2.854 2.229,3.042 0.854,0.188 10 false 23*1, 33*2 5.948,1.385 6.563,1.583 0.615,0.198 10 false CANH 0.573,4.146 0.906,4.333 0.333,0.188 10 false A43 0.896,4.135 1.75,4.323 0.854,0.188 10 false ECM 2.76,3.708 4.74,3.917 1.979,0.208 10 false : CAN Communication Line 2.531,4.042 3.667,4.25 1.135,0.208 10 false *1: for 1AR-FE 5.698,2.833 5.99,3.021 0.292,0.188 10 false 13 5.948,2.948 6.198,3.156 0.25,0.208 10 false TC 5.948,3.583 6.354,3.802 0.406,0.219 10 false CG 5.927,4.156 6.688,4.375 0.76,0.219 10 false F25 DLC3 5.74,3.417 6.083,3.583 0.344,0.167 10 false 4 2.531,4.365 3.667,4.573 1.135,0.208 10 false *2: for 2GR-FKS

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


HINT:

When the warning lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

2.INSPECT DLC3

B

2.INSPECT DLC3
a.
C269872C22
1.5,0.583 1.938,0.854 0.438,0.271 1.583,1.917 1.25,1.333 false 1.813,2.354 2.208,1.323 false 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.594,0.635 1.927,0.833 0.333,0.198 10 false F25 1.104,1.167 1.417,1.417 0.313,0.25 10 false CG 2.146,1.167 2.458,1.417 0.313,0.25 10 false TC
*a Front view of DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F25-13 (TC) - F25-4 (CG) Ignition switch ON 9 to 16 V



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.REPLACE ECM
a.
C269872C22
1.5,0.583 1.938,0.854 0.438,0.271 1.583,1.917 1.25,1.333 false 1.813,2.354 2.208,1.323 false 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.594,0.635 1.927,0.833 0.333,0.198 10 false F25 1.104,1.167 1.417,1.417 0.313,0.25 10 false CG 2.146,1.167 2.458,1.417 0.313,0.25 10 false TC
*a Front view of DLC3


Turn the ignition switch off.



c.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

d.

Check that the EPS warning light is blinking.

OK:

The EPS warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE POWER STEERING ECU ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Disconnect the A43 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1AR-FE
Tester Connection Condition Specified Condition
F25-13 (TC) - A43-23 (TC) Always Below 1 Ω
F25-13 (TC) or A43-23 (TC) - Body ground Always 10 kΩ or higher

for 2GR-FKS
Tester Connection Condition Specified Condition
F25-13 (TC) - A43-33 (TC) Always Below 1 Ω
F25-13 (TC) or A43-33 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C207407C85
1.51,0.865 1.917,1.115 0.406,0.25 1.188,1.406 1.583,1.885 false 0.177,0.177 0.75,0.594 0.573,0.417 10 false *a 1.063,1.219 1.406,1.458 0.344,0.24 10 false CG 1.604,0.906 2.01,1.281 0.406,0.375 10 false F25
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F25-4 (CG) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU

6.REPLACE ECM
a.
C269872C22
1.5,0.583 1.938,0.854 0.438,0.271 1.583,1.917 1.25,1.333 false 1.813,2.354 2.208,1.323 false 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.594,0.635 1.927,0.833 0.333,0.198 10 false F25 1.104,1.167 1.417,1.417 0.313,0.25 10 false CG 2.146,1.167 2.458,1.417 0.313,0.25 10 false TC
*a Front view of DLC3


Replace the ECM.

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>ECM>REMOVAL

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL


b.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

c.

Check that the EPS warning light is blinking.

OK:

The EPS warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE POWER STEERING ECU ASSEMBLY