Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2016.11
RM3160E _59 Vehicle Exterior _019722 LIGHTING (EXT) _0103403 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  High Beam Headlight Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the high beam headlights.

WIRING DIAGRAM

E360544E01
1.781,3.448 4.083,3.74 2.302,0.292 10 false Semiconductor Pwr Integration ECU 2.208,2.938 2.5,3.167 0.292,0.229 10 false 1G 2.25,2.74 2.542,2.969 0.292,0.229 10 false 5 2.219,2.5 2.51,2.729 0.292,0.229 10 false 1D 2.219,2.302 2.51,2.531 0.292,0.229 10 false 14 2.208,2.073 2.5,2.302 0.292,0.229 10 false 1B 2.26,1.885 2.552,2.115 0.292,0.229 10 false 1 2.219,1.656 2.51,1.885 0.292,0.229 10 false 1A 2.271,1.469 2.563,1.698 0.292,0.229 10 false 1 1.646,1.219 2.042,1.438 0.396,0.219 10 false ALT 2.802,0.688 4.104,0.969 1.302,0.281 10 false from Battery 3.073,1.667 3.563,1.906 0.49,0.24 10 false DIMS 2.573,1.656 3.063,1.896 0.49,0.24 10 false ALT 2.563,2.073 3.052,2.313 0.49,0.24 10 false BATT 2.563,2.5 3.052,2.74 0.49,0.24 10 false GND1 2.563,2.938 3.052,3.177 0.49,0.24 10 false GND2 3.094,2.698 3.583,2.938 0.49,0.24 10 false HLHL 3.083,3.094 3.573,3.333 0.49,0.24 10 false HLHR 3.625,3.094 3.917,3.323 0.292,0.229 10 false 1F 3.625,2.896 3.917,3.125 0.292,0.229 10 false 10 3.625,2.688 3.917,2.917 0.292,0.229 10 false 1E 3.677,2.5 3.969,2.729 0.292,0.229 10 false 5 3.615,1.667 3.906,1.896 0.292,0.229 10 false 1D 3.667,1.458 3.958,1.688 0.292,0.229 10 false 2 5.521,1.552 5.813,1.781 0.292,0.229 10 false 24 5.802,1.646 6.292,1.885 0.49,0.24 10 false DIM 5.323,6.26 5.813,6.5 0.49,0.24 10 false F18 5.323,6.417 6.979,6.896 1.656,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 3.323,4.604 3.615,4.833 0.292,0.229 10 false HI 3.333,6.24 3.625,6.469 0.292,0.229 10 false HI 2.563,4.594 2.854,4.823 0.292,0.229 10 false E 2.563,6.229 2.854,6.458 0.292,0.229 10 false E 2.677,4.927 3.448,5.208 0.771,0.281 10 false High Beam 2.656,6.51 3.427,6.792 0.771,0.281 10 false High Beam 3.552,4.604 3.844,4.833 0.292,0.229 10 false 1 3.563,6.24 3.854,6.469 0.292,0.229 10 false 1 2.375,6.24 2.667,6.469 0.292,0.229 10 false 4 2.385,4.615 2.677,4.844 0.292,0.229 10 false 4 2.188,5.25 2.479,5.479 0.292,0.229 10 false A84 2.188,5.396 3.865,5.667 1.677,0.271 10 false Headlight Assembly RH 2.188,6.906 2.479,7.135 0.292,0.229 10 false A82 2.177,7.042 3.854,7.313 1.677,0.271 10 false Headlight Assembly LH

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Check the operation of the low beam headlights. If the low beam headlights do not operate normally, refer to Problem Symptoms Table.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Head Light Hi High beam headlights OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Head Light Hi
50004 123 15
OK:

The high beam headlights illuminate.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK SEMICONDUCTOR PWR INTEGRATION ECU
2.CHECK SEMICONDUCTOR PWR INTEGRATION ECU
a.

Using a voltmeter, check the signal reading of the semiconductor pwr integration ECU.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>ON-VEHICLE INSPECTION

OK:

Output signal reading is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU POWER SOURCE AND BODY GROUND)

NG

INSPECT SEMICONDUCTOR PWR INTEGRATION ECU (RESULTS OF SIGNAL READING CHECK)

3.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU POWER SOURCE AND BODY GROUND)
B352092C08
0.75,3.063 1.083,3.271 0.333,0.208 2.542,3.073 2.875,3.281 0.333,0.208 4.292,3.073 4.625,3.281 0.333,0.208 6.094,3.052 6.427,3.26 0.333,0.208 1.427,4.417 1.083,4.135 false 3.208,4.49 2.906,4.219 false 4.052,4.438 4.26,4.188 false 5.906,4.396 6.115,4.146 false 0.552,0.448 0.865,0.646 0.313,0.198 10 false *a 0.833,3.083 1.146,3.281 0.313,0.198 10 false 1A 4.365,3.104 4.677,3.302 0.313,0.198 10 false 1G 6.188,3.083 6.5,3.281 0.313,0.198 10 false 1B 2.615,3.104 2.927,3.302 0.313,0.198 10 false 1D 1.323,4.427 1.781,4.625 0.458,0.198 10 false ALT 3.063,4.521 3.677,4.719 0.615,0.198 10 false GND1 3.865,4.469 4.479,4.667 0.615,0.198 10 false GND2 5.708,4.417 6.323,4.615 0.615,0.198 10 false BATT
*a Component without semiconductor pwr integration ECU connected
(No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly)
- -


a.

Remove the semiconductor pwr integration ECU from the No. 1 engine room relay block and No. 1 junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1B-1 (BATT) - Body ground Always 11 to 14 V
1A-1 (ALT) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-14 (GND1) - Body ground Always Below 1 Ω
1G-5 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the F18 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-2 (DIMS) - F18-24 (DIM) Always Below 1 Ω
1D-2 (DIMS) or F18-24 (DIM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK SEMICONDUCTOR PWR INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK SEMICONDUCTOR PWR INTEGRATION ECU
a.

Replace the semiconductor pwr integration ECU with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


b.

Check that the high beam headlights operate normally.

OK:

The high beam headlights operate normally.



Result:
Proceed to
OK
NG



OK

END (SEMICONDUCTOR PWR INTEGRATION ECU WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)