The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends the signals to the cooling fan ECU to regulate the cooling fans. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness.
Refer to the System Diagram.
Click hereEngine / Hybrid System>2GR-FKS (COOLING)>COOLING FAN SYSTEM>SYSTEM DIAGRAM
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the ECM, refer to Service Bulletin (for Immobiliser System).
Perform Registration (VIN registration or frame number registration) when replacing the ECM.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION
Make sure to perform Reset Memory (A/T initialization), when replacing the automatic transaxle assembly, ECM or engine assembly.
- for 2WD models: Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION
- for AWD models: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Electric Cooling Fan.
| Tester Display |
|---|
| Control the Electric Cooling Fan |
Check the operation of the cooling fans while operating them using the GTS.
| GTS Operation | Fan Operation |
|---|---|
| ON | Cooling fans operate |
| OFF | Cooling fans stop |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Cooling fans do not operate) | B |
| NG (Cooling fans do not stop) | C |
A
B
C
Disconnect the C1 ECM connector.
Turn the ignition switch to ON.
Check the operation of the cooling fans.
Cooling fans operate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the cooling fan motor RH and cooling fan motor LH.
Click hereEngine / Hybrid System>2GR-FKS (COOLING)>COOLING FAN MOTOR>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Cooling fan motor RH) | B |
| NG (cooling fan motor LH) | C |
A
B
C
| *a | Front view of wire harness connector
(to Cooling Fan ECU) |
Disconnect the A5 cooling fan ECU connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-3 (+B1) - A5-1 (E1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C1 ECM connector.
Disconnect the A5 cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C1-136 (RFC) or A5-2 (SI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A5 cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-1 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the FAN NO. 1 relay.
Click hereEngine / Hybrid System>2GR-FKS (COOLING)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 engine room relay block and No. 1 junction block assembly |
| *2 | FAN NO. 1 Relay |
Remove the FAN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (FAN NO. 1 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A5 cooling fan ECU connector.
Remove the FAN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-3 (+B1) - 5 (FAN NO. 1 relay) | Always | Below 1 Ω |
| A5-3 (+B1) or 5 (FAN NO. 1 relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the FAN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (FAN NO. 1 relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C1 ECM connector.
Disconnect the A5 cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C1-136 (RFC) - A5-2 (SI) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the z1 cooling fan motor RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z1-1 (M-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the z2 cooling fan motor LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z2-1 (M-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG