Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2016.11
RM3160E _59 Vehicle Exterior _019721 WIPER / WASHER _0097860 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Nozzle Heater Circuit  


DESCRIPTION

The main body ECU receives ambient air temperature information from the air conditioning amplifier assembly via CAN communication. The washer nozzle heater sub-assembly controls the main body ECU and operates the washer nozzle heater sub-assembly according to the ambient temperature.

WIRING DIAGRAM

E360433E01
0.26,0.521 1.219,0.927 0.958,0.406 10 false from IG1-NO. 3 Relay 1.625,0.688 2.406,0.948 0.781,0.26 10 false IG1-NO. 2 2.125,1.333 2.646,1.552 0.521,0.219 10 false WHTR 2.698,0.344 3.01,0.542 0.313,0.198 10 false 14 2.74,1.146 2.979,1.344 0.24,0.198 10 false 6 2.688,0.531 3,0.729 0.313,0.198 10 false 2C 2.708,1.333 3.021,1.531 0.313,0.198 10 false J9 0.281,1.76 2.469,2.125 2.188,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 0.208,2.646 3.021,2.865 2.813,0.219 10 false Instrument Panel Junction Block Assembly 5.115,0.896 5.427,1.094 0.313,0.198 10 false 3 5.115,1.24 5.427,1.438 0.313,0.198 10 false 1 5.781,0.896 6.094,1.094 0.313,0.198 10 false 5 5.781,1.24 6.094,1.438 0.313,0.198 10 false 2 5.042,1.635 6.042,1.844 1,0.208 10 false WSH NZL HTR 2.76,3.333 3.073,3.531 0.313,0.198 10 false 2 3.469,3.344 3.781,3.542 0.313,0.198 10 false 2 3.469,4.698 3.781,4.896 0.313,0.198 10 false 1 2.771,4.688 3.083,4.885 0.313,0.198 10 false 1 3.219,3.344 3.375,3.594 0.156,0.25 10 false B 2.99,3.344 3.208,3.615 0.219,0.271 10 false B 3.219,4.688 3.375,4.938 0.156,0.25 10 false E 3,4.688 3.156,4.938 0.156,0.25 10 false E 2.979,5.313 4.719,5.521 1.74,0.208 10 false Washer Nozzle Sub-wire 2.667,5.313 3.021,5.521 0.354,0.208 10 false A36 5,4.042 7.115,4.271 2.115,0.229 10 false Washer Nozzle Sub-assembly LH 5.021,5.115 7.135,5.344 2.115,0.229 10 false Washer Nozzle Sub-assembly RH 4.375,1.938 6.635,2.313 2.26,0.375 10 false No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Disconnect the A36 washer nozzle sub-wire connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Main Body / Active Test.


f.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Washer Nozzle Heater Operate the washer nozzle heater sub-assembly OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Washer Nozzle Heater
50004 123 73

g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-2 (B) - Body ground Ignition switch on, Active Test is not performed Below 1 V
Ignition switch on, Active Test is performed 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (WASHER NOZZLE SUB-WIRE - BODY GROUND)

NG

4.INSPECT WSH NZL HTR RELAY
2.CHECK HARNESS AND CONNECTOR (WASHER NOZZLE SUB-WIRE - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT WASHER NOZZLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT WASHER NOZZLE SUB-ASSEMBLY
a.

Remove the washer nozzle sub-assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER NOZZLE(for Front Side)>REMOVAL


b.

Inspect the washer nozzle sub-assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER NOZZLE(for Front Side)>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE WASHER NOZZLE SUB-ASSEMBLY

4.INSPECT WSH NZL HTR RELAY
a.

Inspect the WSH NZL HTR relay.

Click hereVehicle Exterior>WIPER / WASHER>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WSH NZL HTR RELAY)

NG

REPLACE WSH NZL HTR RELAY

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WSH NZL HTR RELAY)
a.

Disconnect the 2C instrument junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-14 - 5 (WSH NZL HTR relay) Always Below 1 Ω
2C-14 - 2 (WSH NZL HTR relay) Always Below 1 Ω
2C-14 or 5 (WSH NZL HTR relay) - Body ground Always 10 kΩ or higher
2C-14 or 2 (WSH NZL HTR relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WSH NZL HTR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WSH NZL HTR RELAY)
a.

Disconnect the J9 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-6 (WHTR) - 1 (WSH NZL HTR relay) Always Below 1 Ω
J9-6 (WHTR) or 1 (WSH NZL HTR relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (WASHER NOZZLE SUB-ASSEMBLY - WSH NZL HTR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (WASHER NOZZLE SUB-ASSEMBLY - WSH NZL HTR RELAY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-2 (B) - 3 (WSH NZL HTR relay) Always Below 1 Ω
A36-2 (B) or 3 (WSH NZL HTR relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR