Home › Engine / Hybrid System › 2GR-FKS (COOLING) › RADIATOR › from 2016.11
RM3160E _51 Engine / Hybrid System _060161 2GR-FKS COOLING _0297920 RADIATOR G

2GR-FKS COOLING  RADIATOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 16401 1.CHECK RADIATOR CAP SUB-ASSEMBLY

a.
A107446C03
0.479,1.031 0.698,1.229 0.219,0.198 10 false *a 0.708,1.333 1.021,1.49 0.313,0.156 10 false *b 1,1.604 1.313,1.76 0.313,0.156 10 false *c 2.344,1.573 2.656,1.729 0.313,0.156 10 false *d
*a Rubber Packing (1)
*b Rubber Packing (2)
*c Rubber Packing (3)
*d Valve Seat


Measure the valve opening pressure.

i.

If there are water stains or foreign matter on the rubber packings (1), (2) or (3), clean the part(s) with water and finger scouring.


ii.

Check that the rubber packings (1), (2) and (3) are not deformed, cracked or swollen.


iii.

Check that the rubber packing (3) and valve seat are not stuck together.


iv.

Apply engine coolant to the rubber packings (2) and (3) before using a radiator cap tester.


v.
A104601C11
0.375,0.896 0.375,1.521 false 1.719,0.823 1.885,0.365 1.885,0.365 2.094,0.365 false 2.146,0.281 2.323,0.479 0.177,0.198 10 false *a 1.333,0.958 1.531,1.146 0.198,0.188 10 true *b 0.302,1.573 0.479,1.771 0.177,0.198 10 false *1
*1 Radiator Cap Sub-assembly
*a Radiator Cap Tester
*b 30° or more


When using the radiator cap tester, tilt it upward 30° or more.


vi.

Pump the radiator cap tester several times, and check the maximum pressure.

Pumping Speed:

1 pump per second


HINT:

Even if the radiator cap sub-assembly cannot maintain the maximum pressure, it is not a defect.


Result:
Item Specified Condition
Standard value
(for brand-new radiator cap sub-assembly)
94 to 122 kPa (1.0 to 1.2 kgf/cm2, 13.6 to 18 psi)
Minimum standard value
(for used radiator cap sub-assembly)
94 kPa (1.0 kgf/cm2, 13.6 psi)


If the maximum pressure is less than the minimum pressure, replace the radiator cap sub-assembly.



Hide 2.CHECK RADIATOR ASSEMBLY FOR CLOGGING

CAUTION:

To prevent burns, do not touch the engine or other high temperature components while the engine is hot.


a.

Remove the radiator side deflector seal LH.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>REMOVAL


b.

Remove the radiator side seal RH.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>REMOVAL


c.

Remove the cool air intake duct seal.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>REMOVAL


d.

Remove the inlet air cleaner assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


e.

Shine a flashlight at the radiator assembly and cooler condenser assembly from the front of the cooler condenser assembly and check the radiator assembly for clogging using a mirror.

A395371C01
0.594,1.073 0.969,1.073 false 1.5,0.406 1.719,0.406 1.719,0.406 2.01,0.802 false 4.26,1.792 3.906,1.625 3.906,1.625 4.156,1.292 false 6.292,1.458 6.594,1.083 6.594,1.083 6.292,0.792 false 1.344,2.677 1.677,2.906 0.333,0.229 10 true *a 3.854,2.677 4.167,2.917 0.313,0.24 10 true *b 0.406,0.979 0.719,1.135 0.313,0.156 10 false *c 1.333,0.323 1.646,0.479 0.313,0.156 10 false *d 3.74,1.531 3.948,1.74 0.208,0.208 10 false *e 6.635,1 6.844,1.208 0.208,0.208 10 false *e
*a OK *b NG
*c Flashlight *d Mirror
*e Areas to be checked - -


OK:

The radiator assembly is not clogged.


If the radiator assembly is clogged, clean it.


f.

g.

Install the cool air intake duct seal.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>INSTALLATION


h.

Install the radiator side seal RH.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>INSTALLATION


i.

Install the radiator side deflector seal LH.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>INSTALLATION


Hide 3.CLEAN RADIATOR ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine or other high temperature components while the engine is hot.


a.

Remove the radiator side deflector seal LH.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>REMOVAL


b.

Remove the radiator side seal RH.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>REMOVAL


c.

Remove the cool air intake duct seal.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>REMOVAL


d.

Remove the inlet air cleaner assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


e.

Cover the opening of each air duct with a piece of cloth.


f.

Clean the cooler condenser assembly.

i.

Check that the washer nozzle is not clogged.


ii.
A395373

Insert the washer nozzle into the space in front of the cooler condenser assembly and spray it.

NOTICE:
·

Clean the fins of the cooler condenser assembly by spraying the entire area for 150 seconds. Repeat this process twice.

·

Set the air pressure to 0.4 MPa (4.1 kgf/cm2, 58 psi).

·

Check that water sprays in mist form from the nozzle.

·

Keep the nozzle parallel to the cooler condenser assembly.

·

Do not allow the nozzle to contact the fins of the cooler condenser assembly.

·

Keep the nozzle moving while spraying water.

·

Do not spray the cooler compressor assembly or generator assembly excessively.




iii.

Leave the cooler condenser assembly as is for 10 minutes to let the water penetrate the dirt.


iv.

Clean the cooler condenser assembly again.

NOTICE:
·

Clean the fins of the cooler condenser assembly by spraying the entire area for 150 seconds. Repeat this process twice.

·

Set the air pressure to 0.4 MPa (4.1 kgf/cm2, 58 psi).

·

Check that water sprays in mist form from the nozzle.

·

Keep the nozzle parallel to the cooler condenser assembly.

·

Do not allow the nozzle to contact the fins of the cooler condenser assembly.

·

Keep the nozzle moving while spraying water.

·

Do not spray the cooler compressor assembly or generator assembly excessively.




v.

Using an air blow gun, dry the cooler condenser assembly for 3 minutes.



g.
A315240

Disconnect the cooling fan ECU connector.


h.

Disengage the 4 wire harness clamps.


i.
A396001

Disengage the 3 claws and separate the fan shroud assembly from the radiator assembly.


j.

Clean the radiator assembly.

i.
A395372

Insert the washer nozzle between the radiator assembly and fan shroud and spray the radiator assembly.

NOTICE:
·

Clean the fins of the radiator assembly by spraying the entire area for 150 seconds. Repeat this process twice.

·

Set the air pressure to 0.4 MPa (4.1 kgf/cm2, 58 psi).

·

Check that water sprays in mist form from the nozzle.

·

Keep the nozzle parallel to the radiator assembly.

·

Do not allow the nozzle to contact the fins of the radiator assembly.

·

Keep the nozzle moving while spraying water.




ii.

Leave the radiator assembly as is for 10 minutes to let the water penetrate the dirt.


iii.

Clean the radiator assembly again.

NOTICE:
·

Clean the fins of the radiator assembly by spraying the entire area for 150 seconds. Repeat this process twice.

·

Set the air pressure to 0.4 MPa (4.1 kgf/cm2, 58 psi).

·

Check that water sprays in mist form from the nozzle.

·

Keep the nozzle parallel to the radiator assembly.

·

Do not allow the nozzle to contact the fins of the radiator assembly.

·

Keep the nozzle moving while spraying water.




iv.

Using an air blow gun, dry the radiator assembly for 3 minutes.



k.

Check the fins of the radiator assembly for clogs again.

If the radiator assembly is clogged, clean the cooler condenser assembly and radiator assembly again.


l.
A396002

Check that the 3 guides at the bottom are engaged to the radiator assembly.


m.

Engage the 3 claws to install the fan shroud assembly to the radiator assembly.


n.

Engage the 4 wire harness clamps.


o.

Connect the cooling fan ECU connector.


p.

Remove the piece of cloth from the opening of each air duct.


q.

r.

Install the cool air intake duct seal.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>INSTALLATION


s.

Install the radiator side seal RH.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>INSTALLATION


t.

Install the radiator side deflector seal LH.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>RADIATOR GRILLE>INSTALLATION