Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 2 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

Combination meter assembly

·

Power steering ECU assembly

·

Main body ECU (multiplex network body ECU)

·

Steering sensor

·

Airbag sensor assembly

·

ECM

·

Skid control ECU (brake actuator assembly)

·

Air conditioning amplifier assembly

·

Central gateway ECU (network gateway ECU)

·

4WD ECU assembly

(for AWD)

·

Headlight leveling ECU assembly

(w/ Automatic Headlight Beam Level Control System)

·

Certification ECU (smart key ECU assembly)

(w/ Smart Entry and Start System)

·

Clearance warning ECU assembly

(w/ Toyota Parking Assist-sensor System)

·

No. 3 CAN junction connector

·

No. 4 CAN junction connector



WIRING DIAGRAM

C367629E02
0.448,1.073 1.219,1.271 0.771,0.198 10 false 120 Ω 1.125,1.219 1.74,1.417 0.615,0.198 10 false CANL 1.083,0.708 1.698,0.906 0.615,0.198 10 false CANH 0.188,7.188 1.719,7.385 1.531,0.198 10 false *1: for AWD 0.375,1.708 0.833,1.906 0.458,0.198 10 false A43 0.677,1.708 1.135,1.906 0.458,0.198 10 false ECM 1.563,0.708 1.875,0.906 0.313,0.198 10 false 13 1.573,1.188 1.885,1.385 0.313,0.198 10 false 26 2.854,0.698 3.01,0.896 0.156,0.198 10 false 2 2.813,1.177 3.125,1.375 0.313,0.198 10 false 12 2.885,2.552 3.042,2.75 0.156,0.198 10 false 5 2.844,3.052 3.156,3.25 0.313,0.198 10 false 15 0.469,3.594 1.813,4.01 1.344,0.417 10 false Power Steering ECU Assembly 0.25,3.583 0.563,3.781 0.313,0.198 10 false p1 1.073,2.719 1.688,2.917 0.615,0.198 10 false CANH 1.094,3.177 1.708,3.375 0.615,0.198 10 false CANL 1.573,2.563 1.729,2.76 0.156,0.198 10 false 4 1.573,3.063 1.729,3.26 0.156,0.198 10 false 8 0.24,5.365 0.698,5.563 0.458,0.198 10 false F14 0.552,5.365 2.104,5.667 1.552,0.302 10 false 4WD ECU Assembly*1 1.073,4.49 1.688,4.688 0.615,0.198 10 false CANH 1.083,4.958 1.698,5.156 0.615,0.198 10 false CANL 1.573,4.354 1.729,4.552 0.156,0.198 10 false 6 1.573,4.833 1.729,5.031 0.156,0.198 10 false 5 2.854,4.354 3.01,4.552 0.156,0.198 10 false 8 2.813,4.833 3.125,5.031 0.313,0.198 10 false 18 5.729,5.344 6.188,5.542 0.458,0.198 10 false F58 6,5.344 7.094,5.583 1.094,0.24 10 false Steering Sensor 5.594,4.365 5.75,4.563 0.156,0.198 10 false 3 5.594,4.813 5.75,5.01 0.156,0.198 10 false 2 5.813,4.49 6.427,4.688 0.615,0.198 10 false CANH 5.823,4.948 6.438,5.146 0.615,0.198 10 false CANL 4.25,4.323 4.406,4.521 0.156,0.198 10 false 4 4.219,4.813 4.531,5.01 0.313,0.198 10 false 14 2.354,6.656 2.969,6.854 0.615,0.198 10 false F102 2.75,6.656 4.729,6.917 1.979,0.26 10 false No. 3 CAN Junction Connector 5.438,1.729 7.115,2.219 1.677,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 5.146,1.729 5.604,1.927 0.458,0.198 10 false F19 5.552,0.708 5.865,0.906 0.313,0.198 10 false 14 5.552,1.198 5.865,1.396 0.313,0.198 10 false 13 5.823,0.854 6.438,1.052 0.615,0.198 10 false CANH 5.823,1.323 6.438,1.521 0.615,0.198 10 false CANL 4.281,0.698 4.438,0.896 0.156,0.198 10 false 6 4.24,1.188 4.552,1.385 0.313,0.198 10 false 16 4.271,2.563 4.583,2.76 0.313,0.198 10 false 9 4.229,3.042 4.542,3.24 0.313,0.198 10 false 19 5.479,3.573 6.094,3.771 0.615,0.198 10 false A67 5.802,2.719 6.417,2.917 0.615,0.198 10 false CANH 5.813,3.177 6.427,3.375 0.615,0.198 10 false CANL 5.604,2.583 5.917,2.781 0.313,0.198 10 false 6 5.604,3.063 5.917,3.26 0.313,0.198 10 false 7 4.26,5.396 4.417,5.594 0.156,0.198 10 false 1 4.229,5.854 4.542,6.052 0.313,0.198 10 false 11 5.792,3.573 6.99,4.083 1.198,0.51 10 false Headlight Leveling ECU Assembly*2 0.198,7.51 4.115,7.833 3.917,0.323 10 false *2: w/ Automatic Headlight Beam Level Control System 0.115,0.083 1.583,0.323 1.469,0.24 12 false for LHD:

C367630E02
4.26,1.26 4.417,1.458 0.156,0.198 10 false 1 4.24,1.729 4.552,1.927 0.313,0.198 10 false 11 0.104,4.063 0.563,4.26 0.458,0.198 10 false F38 0.396,4.063 2.188,4.302 1.792,0.24 10 false Airbag Sensor Assembly 1.094,3.208 1.708,3.406 0.615,0.198 10 false CANH 1.104,3.667 1.719,3.865 0.615,0.198 10 false CANL 1.573,3.073 1.885,3.271 0.313,0.198 10 false 13 1.583,3.531 1.896,3.729 0.313,0.198 10 false 22 2.875,3.073 3.031,3.271 0.156,0.198 10 false 4 2.833,3.542 3.146,3.74 0.313,0.198 10 false 14 2.885,1.26 3.042,1.458 0.156,0.198 10 false 2 2.844,1.719 3.156,1.917 0.313,0.198 10 false 12 1.583,1.271 1.896,1.469 0.313,0.198 10 false 22 1.583,1.74 1.896,1.938 0.313,0.198 10 false 10 1.094,1.406 1.708,1.604 0.615,0.198 10 false CANH 1.115,1.854 1.729,2.052 0.615,0.198 10 false CANL 0.104,2.292 0.563,2.49 0.458,0.198 10 false A86 0.396,2.292 2,2.844 1.604,0.552 10 false Skid Control ECU (Brake Actuator Assembly) 4.271,3.063 4.427,3.26 0.156,0.198 10 false 3 4.24,3.542 4.552,3.74 0.313,0.198 10 false 13 5.76,3.208 6.375,3.406 0.615,0.198 10 false CANH 5.771,3.677 6.385,3.875 0.615,0.198 10 false CANL 5.5,3.073 5.813,3.271 0.313,0.198 10 false 11 5.5,3.552 5.802,3.875 0.302,0.323 10 false 12 5.24,4.052 5.698,4.25 0.458,0.198 10 false F80 5.542,4.052 7.104,4.5 1.563,0.448 10 false Air Conditioning Amplifier Assembly 4.271,4.708 4.427,4.906 0.156,0.198 10 false 7 4.24,5.177 4.552,5.375 0.313,0.198 10 false 17 5.563,4.729 5.719,4.927 0.156,0.198 10 false 7 5.563,5.177 5.719,5.375 0.156,0.198 10 false 8 5.292,5.719 5.75,5.917 0.458,0.198 10 false F13 5.573,5.719 7.115,6.229 1.542,0.51 10 false Certification ECU (Smart Key ECU Assembly)*2 5.76,4.854 6.375,5.052 0.615,0.198 10 false CANH 5.771,5.313 6.385,5.51 0.615,0.198 10 false CANL 2.896,6.5 3.052,6.698 0.156,0.198 10 false 8 2.865,6.99 3.177,7.188 0.313,0.198 10 false 18 0.469,7.479 2.438,7.781 1.969,0.302 10 false Combination Meter Assembly 1.573,6.51 1.885,6.708 0.313,0.198 10 false 28 1.573,6.99 1.885,7.188 0.313,0.198 10 false 27 1.083,6.51 1.698,6.708 0.615,0.198 10 false CANH 1.104,6.99 1.719,7.188 0.615,0.198 10 false CANL 0.094,7.479 0.781,7.792 0.688,0.313 10 false F126 0.427,6.844 1.198,7.042 0.771,0.198 10 false 120 Ω 4.271,6.51 4.427,6.708 0.156,0.198 10 false 9 4.24,6.99 4.552,7.188 0.313,0.198 10 false 19 5.5,6.51 5.813,6.708 0.313,0.198 10 false 17 5.5,6.99 5.813,7.188 0.313,0.198 10 false 18 5.781,6.625 6.094,6.823 0.313,0.198 10 false R1 5.781,7.115 6.094,7.313 0.313,0.198 10 false R2 5.427,7.479 5.885,7.677 0.458,0.198 10 false F87 5.719,7.479 6.938,7.896 1.219,0.417 10 false Clearance Warning ECU Assembly*1 0.104,8.021 4.375,8.313 4.271,0.292 10 false *1: w/ Toyota Parking Assist-sensor System 0.104,8.323 2.635,8.594 2.531,0.271 10 false *2: w/ Smart Entry and Start System 2.563,7.625 3.177,7.823 0.615,0.198 10 false F103 2.927,7.625 4.948,7.906 2.021,0.281 10 false No. 4 CAN Junction Connector 2.833,4.729 3.146,4.927 0.313,0.198 10 false 10 2.844,5.188 3.156,5.385 0.313,0.198 10 false 20 1.552,4.74 1.865,4.938 0.313,0.198 10 false 18 1.563,5.208 1.875,5.406 0.313,0.198 10 false 17 1.104,4.854 1.719,5.052 0.615,0.198 10 false CA4H 1.115,5.302 1.729,5.5 0.615,0.198 10 false CA4L 0.083,5.719 0.698,5.917 0.615,0.198 10 false F127 0.438,5.719 2.417,6.146 1.979,0.427 10 false Central Gateway ECU (Network Gateway ECU) 0.135,0.094 1.604,0.333 1.469,0.24 12 false for LHD:

C368379E01
0.427,3.583 2.719,3.781 2.292,0.198 10 false Steering Sensor 0.135,3.583 0.594,3.781 0.458,0.198 10 false F58 1.073,2.708 1.688,2.906 0.615,0.198 10 false CANH 1.083,3.167 1.698,3.365 0.615,0.198 10 false CANL 1.573,2.594 1.729,2.792 0.156,0.198 10 false 3 1.573,3.042 1.729,3.24 0.156,0.198 10 false 2 2.865,2.583 3.021,2.781 0.156,0.198 10 false 4 2.823,3.052 3.135,3.25 0.313,0.198 10 false 14 0.438,1.073 1.208,1.271 0.771,0.198 10 false 120 Ω 1.573,0.708 1.885,0.906 0.313,0.198 10 false 28 1.573,1.198 1.885,1.396 0.313,0.198 10 false 27 1.083,0.708 1.698,0.906 0.615,0.198 10 false CANH 1.115,1.198 1.729,1.396 0.615,0.198 10 false CANL 2.865,0.708 3.021,0.906 0.156,0.198 10 false 8 2.823,1.198 3.135,1.396 0.313,0.198 10 false 18 2.365,5.365 2.979,5.563 0.615,0.198 10 false F103 2.74,5.365 4.802,5.646 2.063,0.281 10 false No. 4 CAN Junction Connector 4.271,0.698 4.427,0.896 0.156,0.198 10 false 2 4.229,1.198 4.542,1.396 0.313,0.198 10 false 12 5.26,1.729 5.719,1.927 0.458,0.198 10 false A86 5.552,1.729 7.135,2.281 1.583,0.552 10 false Skid Control ECU (Brake Actuator Assembly) 5.813,0.865 6.427,1.063 0.615,0.198 10 false CANH 5.823,1.323 6.438,1.521 0.615,0.198 10 false CANL 5.552,0.698 5.865,0.896 0.313,0.198 10 false 22 5.552,1.198 5.865,1.396 0.313,0.198 10 false 10 4.26,2.594 4.417,2.792 0.156,0.198 10 false 5 4.229,3.063 4.542,3.26 0.313,0.198 10 false 15 5.573,3.563 5.885,3.76 0.313,0.198 10 false p1 5.781,3.573 7.094,4.021 1.313,0.448 10 false Power Steering ECU Assembly 5.604,2.573 5.76,2.771 0.156,0.198 10 false 4 5.604,3.063 5.76,3.26 0.156,0.198 10 false 8 5.823,2.719 6.438,2.917 0.615,0.198 10 false CANH 5.833,3.177 6.448,3.375 0.615,0.198 10 false CANL 4.281,4.125 4.438,4.323 0.156,0.198 10 false 1 4.26,4.625 4.573,4.823 0.313,0.198 10 false 11 2.427,8.031 3.042,8.229 0.615,0.198 10 false F102 2.802,8.031 4.969,8.313 2.167,0.281 10 false No. 3 CAN Junction Connector 4.302,6.313 4.458,6.51 0.156,0.198 10 false 1 4.281,6.771 4.594,6.969 0.313,0.198 10 false 11 0.094,1.708 0.708,1.906 0.615,0.198 10 false F126 0.458,1.708 2.448,2.01 1.99,0.302 10 false Combination Meter Assembly 0.115,0.073 1.583,0.313 1.469,0.24 12 false for RHD:

C368380E01
0.115,0.073 1.583,0.313 1.469,0.24 12 false for RHD: 2.844,1.271 3.156,1.469 0.313,0.198 10 false 10 2.854,1.74 3.167,1.938 0.313,0.198 10 false 20 1.573,1.271 1.885,1.469 0.313,0.198 10 false 18 1.583,1.75 1.896,1.948 0.313,0.198 10 false 17 1.115,1.406 1.729,1.604 0.615,0.198 10 false CA4H 1.135,1.865 1.75,2.063 0.615,0.198 10 false CA4L 0.063,2.292 0.677,2.49 0.615,0.198 10 false F127 0.427,2.292 2.396,2.844 1.969,0.552 10 false Central Gateway ECU (Network Gateway ECU) 2.896,6.5 3.052,6.698 0.156,0.198 10 false 2 2.854,6.969 3.167,7.167 0.313,0.198 10 false 12 1.552,6.51 1.865,6.708 0.313,0.198 10 false 13 1.563,6.969 1.875,7.167 0.313,0.198 10 false 26 0.427,6.865 1.042,7.198 0.615,0.333 10 false 120 Ω 1.073,6.51 1.688,6.708 0.615,0.198 10 false CANH 1.094,6.969 1.708,7.167 0.615,0.198 10 false CANL 4.271,6.5 4.427,6.698 0.156,0.198 10 false 3 4.24,6.979 4.552,7.177 0.313,0.198 10 false 13 0.51,7.5 0.969,7.698 0.458,0.198 10 false A43 0.823,7.5 1.281,7.698 0.458,0.198 10 false ECM 5.198,7.49 5.656,7.688 0.458,0.198 10 false F80 5.51,7.49 7.104,7.948 1.594,0.458 10 false Air Conditioning Amplifier Assembly 5.51,6.479 5.823,6.677 0.313,0.198 10 false 11 5.51,6.99 5.823,7.188 0.313,0.198 10 false 12 5.771,6.625 6.385,6.823 0.615,0.198 10 false CANH 5.781,7.094 6.396,7.292 0.615,0.198 10 false CANL 2.885,4.708 3.042,4.906 0.156,0.198 10 false 4 2.844,5.177 3.156,5.375 0.313,0.198 10 false 14 0.125,5.729 0.583,5.927 0.458,0.198 10 false F38 0.406,5.729 2.271,6.104 1.865,0.375 10 false Airbag Sensor Assembly 1.073,4.854 1.688,5.052 0.615,0.198 10 false CANH 1.083,5.313 1.698,5.51 0.615,0.198 10 false CANL 1.563,4.729 1.875,4.927 0.313,0.198 10 false 13 1.573,5.188 1.885,5.385 0.313,0.198 10 false 22 4.281,4.708 4.438,4.906 0.156,0.198 10 false 5 4.25,5.177 4.563,5.375 0.313,0.198 10 false 15 5.5,4.708 5.813,4.906 0.313,0.198 10 false 17 5.5,5.188 5.813,5.385 0.313,0.198 10 false 18 5.49,5.729 5.948,5.927 0.458,0.198 10 false F87 5.781,5.729 7.021,6.24 1.24,0.51 10 false Clearance Warning ECU Assembly*3 5.771,4.854 6.083,5.052 0.313,0.198 10 false R1 5.771,5.323 6.083,5.521 0.313,0.198 10 false R2 2.885,3.073 3.042,3.271 0.156,0.198 10 false 6 2.844,3.552 3.156,3.75 0.313,0.198 10 false 16 1.563,3.083 1.875,3.281 0.313,0.198 10 false 14 1.563,3.552 1.875,3.75 0.313,0.198 10 false 13 0.406,4.063 2.083,4.615 1.677,0.552 10 false Main Body ECU (Multiplex Network Body ECU) 0.115,4.063 0.573,4.26 0.458,0.198 10 false F19 1.063,3.208 1.677,3.406 0.615,0.198 10 false CANH 1.083,3.667 1.698,3.865 0.615,0.198 10 false CANL 4.292,3.063 4.448,3.26 0.156,0.198 10 false 7 4.26,3.531 4.573,3.729 0.313,0.198 10 false 17 5.229,4.052 5.688,4.25 0.458,0.198 10 false F13 5.531,4.052 7.104,4.583 1.573,0.531 10 false Certification ECU (Smart Key ECU Assembly)*2 5.542,3.063 5.698,3.26 0.156,0.198 10 false 7 5.542,3.542 5.698,3.74 0.156,0.198 10 false 8 5.76,3.208 6.375,3.406 0.615,0.198 10 false CANH 5.771,3.677 6.385,3.875 0.615,0.198 10 false CANL 5.271,2.302 5.729,2.5 0.458,0.198 10 false F14 5.573,2.302 7.094,2.563 1.521,0.26 10 false 4WD ECU Assembly*1 5.542,1.281 5.698,1.479 0.156,0.198 10 false 6 5.542,1.76 5.698,1.958 0.156,0.198 10 false 5 5.76,1.406 6.375,1.604 0.615,0.198 10 false CANH 5.76,1.875 6.375,2.073 0.615,0.198 10 false CANL 4.281,1.292 4.438,1.49 0.156,0.198 10 false 8 4.25,1.75 4.563,1.948 0.313,0.198 10 false 18 0.146,7.802 1.833,8 1.688,0.198 10 false *1: for AWD 0.156,8.115 2.604,8.365 2.448,0.25 10 false *2: w/ Smart Entry and Start System 0.156,8.427 3.188,8.698 3.031,0.271 10 false *3: w/ Toyota Parking Assist-sensor System 2.438,7.635 3.052,7.833 0.615,0.198 10 false F102 2.802,7.635 4.781,7.927 1.979,0.292 10 false No. 3 CAN junction connector

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 60 km/h (37 mph) or more for 9 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.*

*: w/ Smart Entry and Start System




HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)

B

6.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F102 No. 3 CAN junction connector.

C287238C78
5.313,0.104 5.688,0.427 0.375,0.323 2.073,0.125 2.521,0.438 0.448,0.313 6.396,2.76 6.26,2.76 6.26,2.76 6.146,2.177 true 1.5,2.073 0.927,1.417 0.927,1.417 0.813,1.417 true 0.896,2.917 1.01,2.917 1.01,2.917 1.521,2.292 true 1.938,2.083 1.354,1.146 1.354,1.146 1.135,1.146 true 1.177,3.146 1.396,3.146 1.396,3.146 1.938,2.281 true 2.167,2.052 1.406,0.844 1.406,0.844 1.146,0.844 true 1.313,3.354 1.563,3.354 1.563,3.354 2.167,2.281 true 0.896,2.542 1,2.542 1,2.542 1.271,2.281 true 1.281,2.073 0.979,1.833 0.979,1.833 0.875,1.833 true 2.385,2.063 2.938,0.552 2.938,0.552 3.052,0.552 true 2.917,3.375 2.76,3.375 2.76,3.375 2.396,2.271 true 2.833,2.063 3.323,0.781 3.323,0.781 3.438,0.781 true 3.333,3.177 3.219,3.177 3.219,3.177 2.844,2.281 true 3.052,2.063 3.479,1.073 3.479,1.073 3.594,1.073 true 3.417,2.938 3.313,2.938 3.313,2.938 3.052,2.271 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 4.667,0.156 4.979,0.354 0.313,0.198 10 false *1 6.479,2.677 6.938,2.875 0.458,0.198 10 false BAT 0.323,1.75 1.24,1.948 0.917,0.198 10 false CANH*b 0.375,2.448 1.292,2.646 0.917,0.198 10 false CANL*b 0.281,1.323 1.198,1.521 0.917,0.198 10 false CANH*c 0.375,2.833 1.073,3.083 0.698,0.25 10 false CANL*c 0.573,1.063 1.49,1.26 0.917,0.198 10 false CANH*d 0.646,3.063 1.563,3.26 0.917,0.198 10 false CANL*d 5.385,0.167 5.698,0.365 0.313,0.198 10 false F25 2.146,0.177 2.76,0.375 0.615,0.198 10 false F102 0.792,3.271 1.438,3.479 0.646,0.208 10 false CANL*e 0.604,0.75 1.552,0.948 0.948,0.198 10 false CANH*e 3.115,0.479 4.031,0.677 0.917,0.198 10 false CANH*f 2.958,3.302 3.875,3.5 0.917,0.198 10 false CANL*f 3.49,0.708 4.406,0.906 0.917,0.198 10 false CANH*g 3.396,3.104 4.313,3.302 0.917,0.198 10 false CANL*g 3.656,1 4.573,1.198 0.917,0.198 10 false CANH*h 3.49,2.865 4.406,3.063 0.917,0.198 10 false CANL*h
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to ECM *d to Steering Sensor
*e to Power Steering ECU Assembly *f to Main Body ECU (Multiplex Network Body ECU)
*g to 4WD ECU Assembly
(for AWD)
*h to Headlight Leveling ECU Assembly
(w/ Automatic Headlight Beam Level Control System)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F102-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 4 CAN junction connector
F102-11 (CANL) - F25-16 (BAT)
F102-2 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
F102-12 (CANL) - F25-16 (BAT)
F102-4 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Steering sensor
F102-14 (CANL) - F25-16 (BAT)
F102-5 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Power steering ECU assembly
F102-15 (CANL) - F25-16 (BAT)
F102-6 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Main body ECU (multiplex network body ECU)
F102-16 (CANL) - F25-16 (BAT)
F102-8 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher 4WD ECU assembly*1
F102-18 (CANL) - F25-16 (BAT)
F102-9 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Headlight leveling ECU assembly*2
F102-19 (CANL) - F25-16 (BAT)


·

*1: for AWD

·

*2: w/ Automatic Headlight Beam Level Control System



Result:
Result Proceed to
OK A
NG (No. 4 CAN junction connector main line) B
NG (ECU or sensor bus line) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
3.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the F102 No. 3 CAN junction connector.


b.

Disconnect the F103 No. 4 CAN junction connector.

C287238C79
5.313,0.104 5.771,0.406 0.458,0.302 2.073,0.125 2.521,0.427 0.448,0.302 6.396,2.76 6.26,2.76 6.26,2.76 6.146,2.177 true 1.5,2.073 0.927,1.417 0.927,1.417 0.813,1.417 true 0.896,2.917 1.01,2.917 1.01,2.917 1.521,2.292 true 1.719,2.073 1.094,0.917 1.094,0.917 0.969,0.917 true 1.083,3.292 1.177,3.292 1.177,3.292 1.729,2.281 true 1.448,3.51 1.563,3.51 1.563,3.51 1.938,2.281 true 1.948,2.073 1.333,0.615 1.333,0.615 1.208,0.615 true 0.896,2.542 1,2.542 1,2.542 1.271,2.281 true 1.281,2.073 0.979,1.833 0.979,1.833 0.875,1.833 true 3.063,2.094 3.458,1.208 3.458,1.208 3.729,1.208 true 3.646,2.771 3.458,2.771 3.458,2.771 3.052,2.26 true 2.615,2.083 3.115,0.563 3.115,0.563 3.219,0.563 true 3.167,3.365 3.073,3.365 3.073,3.365 2.615,2.281 true 2.833,2.083 3.323,0.865 3.323,0.865 3.396,0.865 true 3.323,3.063 3.219,3.063 3.219,3.063 2.865,2.271 true 3.281,2.073 3.615,1.635 3.615,1.635 3.729,1.635 true 3.76,2.5 3.667,2.5 3.667,2.5 3.292,2.292 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 4.51,0.135 4.823,0.333 0.313,0.198 10 false *1 6.479,2.677 6.938,2.875 0.458,0.198 10 false BAT 0.323,1.75 1.24,1.948 0.917,0.198 10 false CANH*b 0.375,2.448 1.292,2.646 0.917,0.198 10 false CANL*b 0.281,1.323 1.198,1.521 0.917,0.198 10 false CANH*c 0.375,2.833 1.073,3.083 0.698,0.25 10 false CANL*c 0.406,0.823 1.323,1.021 0.917,0.198 10 false CANH*d 0.552,3.188 1.469,3.385 0.917,0.198 10 false CANL*d 0.635,0.531 1.552,0.729 0.917,0.198 10 false CANH*e 0.885,3.427 1.802,3.625 0.917,0.198 10 false CANL*e 5.417,0.167 5.729,0.365 0.313,0.198 10 false F25 2.146,0.177 2.76,0.375 0.615,0.198 10 false F103 3.229,3.292 4.146,3.49 0.917,0.198 10 false CANL*f 3.281,0.479 4.198,0.677 0.917,0.198 10 false CANH*f 3.854,2.406 4.771,2.604 0.917,0.198 10 false CANL*i 3.792,1.135 4.708,1.333 0.917,0.198 10 false CANH*h 3.708,2.698 4.625,2.896 0.917,0.198 10 false CANL*h 3.823,1.542 4.74,1.74 0.917,0.198 10 false CANH*i 3.385,2.99 4.302,3.188 0.917,0.198 10 false CANL*g 3.448,0.792 4.365,0.99 0.917,0.198 10 false CANH*g
*1 DLC3 - -
*a Front view of wire harness connector
(No. 4 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
*c to Skid Control ECU (Brake Actuator Assembly) *d to Air Conditioning Amplifier Assembly
*e to Airbag Sensor Assembly *f to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System)
*g to Combination Meter Assembly *h to Clearance Warning ECU Assembly
(w/ Toyota Parking Assist-sensor System)
*i to Central Gateway ECU (Network Gateway ECU) - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F103-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 3 CAN junction connector
F103-11 (CANL) - F25-16 (BAT)
F103-2 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Skid control ECU (brake actuator assembly)
F103-12 (CANL) - F25-16 (BAT)
F103-3 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Air conditioning amplifier assembly
F103-13 (CANL) - F25-16 (BAT)
F103-4 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Airbag sensor assembly
F103-14 (CANL) - F25-16 (BAT)
F103-7 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Certification ECU (smart key ECU assembly)*1
F103-17 (CANL) - F25-16 (BAT)
F103-8 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Combination meter assembly
F103-18 (CANL) - F25-16 (BAT)
F103-9 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Clearance warning ECU assembly*2
F103-19 (CANL) - F25-16 (BAT)
F103-10 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
F103-20 (CANL) - F25-16 (BAT)


·

*1: w/ Smart Entry and Start System

·

*2: w/ Toyota Parking Assist-sensor System



Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector main line) B
NG (ECU or sensor bus line) C
NG (Central gateway ECU (network gateway ECU) branch line) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)

D

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C351161C93
5.083,0.292 5.49,0.563 0.406,0.271 1.635,0.156 2.042,0.406 0.406,0.25 6.104,2.24 5.958,2.24 5.958,2.24 5.958,1.719 true 2.094,0.708 1.948,0.708 1.948,0.708 1.948,1.427 true 1.708,0.708 1.854,0.708 1.854,0.708 1.854,1.427 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 3.938,0.063 4.25,0.26 0.313,0.198 10 false *1 5.167,0.354 5.646,0.656 0.479,0.302 10 false F25 6.198,2.167 6.719,2.385 0.521,0.219 10 false BAT 1.688,0.198 2.188,0.5 0.5,0.302 10 false F127 2.167,0.625 2.635,0.833 0.469,0.208 10 false CA4L 1.302,0.625 1.771,0.833 0.469,0.208 10 false CA4H
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F127-18 (CA4H) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F127-17 (CA4L) - F25-16 (BAT)


HINT:
·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINE OR CONNECTOR

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F127 central gateway ECU (network gateway ECU) connector.


b.
C355867C37
1.438,0.104 1.885,0.354 0.448,0.25 1.51,1.781 1.646,1.781 1.646,1.781 1.646,1.198 true 1.938,1.781 1.781,1.781 1.781,1.781 1.781,1.198 true 0.656,0.323 0.5,0.323 0.5,0.323 0.49,0.906 true 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a 1.51,0.156 2.083,0.542 0.573,0.385 10 false F127 2.01,1.698 2.5,1.896 0.49,0.198 10 false CA4H 1.115,1.708 1.604,1.906 0.49,0.198 10 false CA4L 0.76,0.24 1.25,0.438 0.49,0.198 10 false BATT
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F127-18 (CA4H) - F127-1 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F127-17 (CA4L) - F127-1 (BATT)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

6.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F102 No. 3 CAN junction connector.

C287238C86
5.313,0.104 5.688,0.427 0.375,0.323 2.073,0.125 2.521,0.438 0.448,0.313 6.396,2.76 6.26,2.76 6.26,2.76 6.146,2.177 true 1.5,2.073 0.927,1.417 0.927,1.417 0.813,1.417 true 0.896,2.917 1.01,2.917 1.01,2.917 1.521,2.292 true 1.948,2.083 1.219,0.833 1.219,0.833 0.958,0.833 true 1.031,3.385 1.25,3.385 1.25,3.385 1.948,2.271 true 2.156,2.083 1.396,0.563 1.396,0.563 1.135,0.563 true 1.177,3.594 1.427,3.594 1.427,3.594 2.177,2.271 true 0.896,2.542 1,2.542 1,2.542 1.271,2.281 true 1.281,2.073 0.979,1.833 0.979,1.833 0.875,1.833 true 2.385,2.063 2.938,0.552 2.938,0.552 3.052,0.552 true 3.135,3.573 2.823,3.573 2.823,3.573 2.385,2.26 true 3.333,3.177 3.219,3.177 3.219,3.177 2.844,2.281 true 2.833,2.083 3.26,1.031 3.26,1.031 3.417,1.031 true 1.729,2.094 1.083,1.094 1.083,1.094 0.823,1.094 true 0.906,3.167 1.125,3.167 1.125,3.167 1.719,2.281 true 3.281,3.365 3,3.365 3,3.365 2.615,2.271 true 3.813,2.667 3.531,2.667 3.531,2.667 3.281,2.26 true 2.604,2.094 3.094,0.813 3.094,0.813 3.208,0.813 true 3.292,2.083 3.552,1.552 3.552,1.552 3.802,1.552 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 4.667,0.156 4.979,0.354 0.313,0.198 10 false *1 6.479,2.677 6.938,2.875 0.458,0.198 10 false BAT 0.323,1.75 1.24,1.948 0.917,0.198 10 false CANH*b 0.375,2.448 1.292,2.646 0.917,0.198 10 false CANL*b 0.281,1.323 1.198,1.521 0.917,0.198 10 false CANH*c 0.375,2.833 1.073,3.083 0.698,0.25 10 false CANL*c 0.271,1.01 1.188,1.208 0.917,0.198 10 false CANH*d 0.385,3.083 1.302,3.281 0.917,0.198 10 false CANL*d 5.385,0.167 5.698,0.365 0.313,0.198 10 false F25 2.146,0.177 2.76,0.375 0.615,0.198 10 false F102 0.5,3.302 1.146,3.51 0.646,0.208 10 false CANL*e 0.406,0.75 1.354,0.948 0.948,0.198 10 false CANH*e 0.615,0.479 1.531,0.677 0.917,0.198 10 false CANH*f 0.688,3.521 1.604,3.719 0.917,0.198 10 false CANL*f 3.104,0.479 4.021,0.677 0.917,0.198 10 false CANH*g 3.198,3.5 4.115,3.698 0.917,0.198 10 false CANL*g 3.26,0.74 4.177,0.938 0.917,0.198 10 false CANH*h 3.333,3.292 4.25,3.49 0.917,0.198 10 false CANL*h 3.469,0.958 4.385,1.156 0.917,0.198 10 false CANH*i 3.865,1.479 4.781,1.677 0.917,0.198 10 false CANH*j 3.396,3.104 4.313,3.302 0.917,0.198 10 false CANL*i 3.875,2.604 4.792,2.802 0.917,0.198 10 false CANL*j
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to ECM *d to Air Conditioning Amplifier Assembly
*e to Airbag Sensor Assembly *f to Clearance Warning ECU Assembly
(w/ Toyota Parking Assist-sensor System)
*g to Main Body ECU (Multiplex Network Body ECU) *h to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System)
*i to 4WD ECU Assembly
(for AWD)
*j to Central Gateway ECU (Network Gateway ECU)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F102-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 4 CAN junction connector
F102-11 (CANL) - F25-16 (BAT)
F102-2 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
F102-12 (CANL) - F25-16 (BAT)
F102-3 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Air conditioning amplifier assembly
F102-13 (CANL) - F25-16 (BAT)
F102-4 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Airbag sensor assembly
F102-14 (CANL) - F25-16 (BAT)
F102-5 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Clearance warning ECU assembly*1
F102-15 (CANL) - F25-16 (BAT)
F102-6 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Main body ECU (multiplex network body ECU)
F102-16 (CANL) - F25-16 (BAT)
F102-7 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Certification ECU (smart key ECU assembly)*2
F102-17 (CANL) - F25-16 (BAT)
F102-8 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher 4WD ECU assembly*3
F102-18 (CANL) - F25-16 (BAT)
F102-10 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
F102-20 (CANL) - F25-16 (BAT)


·

*1: w/ Toyota Parking Assist-sensor System

·

*2: w/ Smart Entry and Start System

·

*3: for AWD



Result:
Result Proceed to
OK A
NG (No. 4 CAN junction connector main line) B
NG (ECU or sensor bus line) C
NG (Central gateway ECU (network gateway ECU) branch line) D



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)

C

8.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)

D

9.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
7.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the F102 No. 3 CAN junction connector.


b.

Disconnect the F103 No. 4 CAN junction connector.

C287238C81
5.313,0.104 5.771,0.406 0.458,0.302 2.073,0.125 2.521,0.427 0.448,0.302 6.396,2.76 6.26,2.76 6.26,2.76 6.146,2.177 true 1.5,2.073 0.927,1.417 0.927,1.417 0.813,1.417 true 0.896,2.917 1.01,2.917 1.01,2.917 1.521,2.292 true 1.938,2.073 1.313,0.917 1.313,0.917 1.188,0.917 true 1.583,3.51 1.802,3.51 1.802,3.51 2.177,2.281 true 0.896,2.542 1,2.542 1,2.542 1.271,2.281 true 1.281,2.073 0.979,1.833 0.979,1.833 0.875,1.833 true 2.833,2.083 3.323,0.865 3.323,0.865 3.396,0.865 true 3.323,3.063 3.219,3.063 3.219,3.063 2.865,2.271 true 2.156,2.094 1.448,0.698 1.448,0.698 1.323,0.698 true 1.281,3.156 1.635,3.156 1.635,3.156 1.958,2.271 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 4.51,0.135 4.823,0.333 0.313,0.198 10 false *1 6.479,2.677 6.938,2.875 0.458,0.198 10 false BAT 0.323,1.75 1.24,1.948 0.917,0.198 10 false CANH*b 0.375,2.448 1.292,2.646 0.917,0.198 10 false CANL*b 0.281,1.323 1.198,1.521 0.917,0.198 10 false CANH*c 0.375,2.833 1.073,3.083 0.698,0.25 10 false CANL*c 0.625,0.833 1.542,1.031 0.917,0.198 10 false CANH*d 0.75,3.073 1.667,3.271 0.917,0.198 10 false CANL*d 0.771,0.604 1.688,0.802 0.917,0.198 10 false CANH*e 1.052,3.417 1.969,3.615 0.917,0.198 10 false CANL*e 5.417,0.167 5.729,0.365 0.313,0.198 10 false F25 2.146,0.177 2.76,0.375 0.615,0.198 10 false F103 3.385,2.99 4.302,3.188 0.917,0.198 10 false CANL*f 3.448,0.792 4.365,0.99 0.917,0.198 10 false CANH*f
*1 DLC3 - -
*a Front view of wire harness connector
(No. 4 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
*c to Skid Control ECU (Brake Actuator Assembly) *d to Steering Sensor
*e to Power Steering ECU Assembly *f to Combination Meter Assembly



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F103-1 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 3 CAN junction connector
F103-11 (CANL) - F25-16 (BAT)
F103-2 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Skid control ECU (brake actuator assembly)
F103-12 (CANL) - F25-16 (BAT)
F103-4 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Steering sensor
F103-14 (CANL) - F25-16 (BAT)
F103-5 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Power steering ECU assembly
F103-15 (CANL) - F25-16 (BAT)
F103-8 (CANH) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Combination meter assembly
F103-18 (CANL) - F25-16 (BAT)



Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector main line) B
NG (ECU or sensor bus line) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

C

8.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
8.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C351161C93
5.083,0.292 5.49,0.563 0.406,0.271 1.635,0.156 2.042,0.406 0.406,0.25 6.104,2.24 5.958,2.24 5.958,2.24 5.958,1.719 true 2.094,0.708 1.948,0.708 1.948,0.708 1.948,1.427 true 1.708,0.708 1.854,0.708 1.854,0.708 1.854,1.427 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 3.938,0.063 4.25,0.26 0.313,0.198 10 false *1 5.167,0.354 5.646,0.656 0.479,0.302 10 false F25 6.198,2.167 6.719,2.385 0.521,0.219 10 false BAT 1.688,0.198 2.188,0.5 0.5,0.302 10 false F127 2.167,0.625 2.635,0.833 0.469,0.208 10 false CA4L 1.302,0.625 1.771,0.833 0.469,0.208 10 false CA4H
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F127-18 (CA4H) - F25-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F127-17 (CA4L) - F25-16 (BAT)


HINT:
·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINE OR CONNECTOR

9.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F127 central gateway ECU (network gateway ECU) connector.


b.
C355867C37
1.438,0.104 1.885,0.354 0.448,0.25 1.51,1.781 1.646,1.781 1.646,1.781 1.646,1.198 true 1.938,1.781 1.781,1.781 1.781,1.781 1.781,1.198 true 0.656,0.323 0.5,0.323 0.5,0.323 0.49,0.906 true 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a 1.51,0.156 2.083,0.542 0.573,0.385 10 false F127 2.01,1.698 2.5,1.896 0.49,0.198 10 false CA4H 1.115,1.708 1.604,1.906 0.49,0.198 10 false CA4L 0.76,0.24 1.25,0.438 0.49,0.198 10 false BATT
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F127-18 (CA4H) - F127-1 (BATT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F127-17 (CA4L) - F127-1 (BATT)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))