Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 3 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Central gateway ECU (network gateway ECU)

·

Navigation receiver assembly

(for Navigation Receiver Type)

·

Radio and display receiver assembly

(for Radio and Display Type)

·

Telematics transceiver

(w/ Telematics Transceiver)

·

No. 7 CAN junction connector



WIRING DIAGRAM

C353599E08
0.344,1.094 0.885,1.375 0.542,0.281 10 false 120 Ω 0.333,5.229 0.875,5.51 0.542,0.281 10 false 120 Ω 0.917,0.74 1.417,0.938 0.5,0.198 10 false CA3H 1.448,0.74 1.698,0.906 0.25,0.167 10 false 6 0.917,1.229 1.417,1.427 0.5,0.198 10 false CA3L 1.427,1.229 1.677,1.396 0.25,0.167 10 false 21 3.646,0.74 3.896,0.906 0.25,0.167 10 false 1 3.604,1.219 3.854,1.385 0.25,0.167 10 false 12 4.792,1.26 5.042,1.427 0.25,0.167 10 false 4 4.76,1.74 5.01,1.906 0.25,0.167 10 false 15 5.781,1.26 6.125,1.563 0.344,0.302 10 false 15 6.063,1.385 6.708,1.698 0.646,0.313 10 false CANP 6.063,1.865 6.615,2.104 0.552,0.24 10 false CANN 5.781,1.75 6.125,1.99 0.344,0.24 10 false 16 5.052,2.302 5.604,2.615 0.552,0.313 10 false F140 5.448,2.302 7.115,2.563 1.667,0.26 10 false Telematics Transceiver*1 4.792,3.625 5.042,3.823 0.25,0.198 10 false 5 4.771,4.104 5.073,4.333 0.302,0.229 10 false 16 5.844,3.635 6.094,3.802 0.25,0.167 10 false 9 5.792,4.104 6.042,4.271 0.25,0.167 10 false 10 6.083,3.74 6.583,3.938 0.5,0.198 10 false CANH 6.073,4.219 6.573,4.417 0.5,0.198 10 false CANL 4.76,4.656 5.188,4.885 0.427,0.229 10 false F116 5.135,4.656 7.125,4.938 1.99,0.281 10 false Navigation Receiver Assembly*2 5.135,5.094 6.813,5.583 1.677,0.49 10 false Radio and Display Receiver Assembly*3 3.635,4.854 3.885,5.021 0.25,0.167 10 false 2 3.594,5.333 3.844,5.5 0.25,0.167 10 false 13 1.396,4.865 1.646,5.031 0.25,0.167 10 false 19 1.396,5.333 1.646,5.5 0.25,0.167 10 false 20 0.906,4.865 1.406,5.063 0.5,0.198 10 false CAYH 0.938,5.344 1.438,5.542 0.5,0.198 10 false CAYL 0.063,5.844 0.49,6.052 0.427,0.208 10 false F127 0.427,5.844 2.354,6.344 1.927,0.5 10 false Central Gateway ECU (Network Gateway ECU) 3.094,5.792 3.49,5.979 0.396,0.188 10 false F135 3.469,5.792 5.458,6.073 1.99,0.281 10 false No. 7 CAN Junction Connector 2.448,6.188 4.938,6.521 2.49,0.333 10 false *1: w/ Telematics Transceiver 2.448,6.51 4.635,6.75 2.188,0.24 10 false *2: for Navigation Receiver Type 4.615,6.188 6.563,6.417 1.948,0.229 10 false *3: for Radio and Display Type 4.813,5.094 5.146,5.26 0.333,0.167 10 false F71

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 31 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F135 No. 7 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C292404C56
3.177,0.302 3.625,0.563 0.448,0.26 2.729,1.698 2.188,0.885 2.188,0.885 2.042,0.885 true 2.844,1.698 2.375,0.552 2.375,0.552 2.24,0.552 true 3.25,1.698 4.219,0.74 4.219,0.74 4.448,0.74 true 3.24,1.927 4.219,2.469 4.219,2.469 4.448,2.469 true 2.188,2.365 2.417,2.365 2.417,2.365 2.844,1.917 true 1.99,2.135 2.24,2.135 2.24,2.135 2.719,1.906 true 3.115,1.708 2.594,0.26 2.594,0.26 2.438,0.26 true 2.375,2.583 2.573,2.583 2.573,2.583 3.115,1.917 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.24,0.354 3.771,0.604 0.531,0.25 10 false F135 1.479,0.813 2.396,1.01 0.917,0.198 10 false CANH*b 1.865,0.198 2.781,0.396 0.917,0.198 10 false CANH*c 1.823,2.521 2.74,2.719 0.917,0.198 10 false CANL*c 1.458,2.063 2.375,2.26 0.917,0.198 10 false CANL*b 4.542,0.646 5.458,0.844 0.917,0.198 10 false CANH*d*e 4.542,2.396 5.458,2.594 0.917,0.198 10 false CANL*d*e 1.635,2.302 2.552,2.5 0.917,0.198 10 false CANL*b 1.667,0.5 2.583,0.698 0.917,0.198 10 false CANH*b
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Telematics Transceiver
(w/ Telematics Transceiver)
*d to Navigation Receiver Assembly
(for Navigation Receiver Type)
*e to Radio and Display Receiver Assembly
(for Radio and Display Type)
- -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F135-1 (CANH) - F135-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F135-2 (CANH) - F135-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F135-4 (CANH) - F135-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Telematics transceiver*1
F135-5 (CANH) - F135-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Navigation receiver assembly*2
F135-5 (CANH) - F135-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly*3


·

*1: w/ Telematics Transceiver

·

*2: for Navigation Receiver Type

·

*3: for Radio and Display Type


HINT:

If there is a short in a CAN bus line without any CAN compatible optional devices connected to the option connector, repair or replace the CAN bus branch line or the option connector.



Result:
Result Proceed to
OK A
NG (Central gateway ECU (network gateway ECU) main line) B
NG (ECU or sensor branch line) C



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
2.CHECK FOR SHORT IN CAN BUS LINES (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F127 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C292404C57
3.177,0.302 3.625,0.563 0.448,0.26 2.729,1.698 2.188,0.885 2.188,0.885 2.042,0.885 true 2.844,1.698 2.375,0.552 2.375,0.552 2.24,0.552 true 2.188,2.365 2.417,2.365 2.417,2.365 2.844,1.917 true 1.99,2.135 2.24,2.135 2.24,2.135 2.719,1.906 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.24,0.354 3.771,0.604 0.531,0.25 10 false F135 1.479,0.813 2.396,1.01 0.917,0.198 10 false CANH*b 1.458,2.063 2.375,2.26 0.917,0.198 10 false CANL*b 1.635,2.302 2.552,2.5 0.917,0.198 10 false CANL*b 1.667,0.5 2.583,0.698 0.917,0.198 10 false CANH*b
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F135-1 (CANH) - F135-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher
F135-2 (CANH) - F135-13 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C365514C10
1.5,0.177 2.01,0.448 0.51,0.271 1.396,1 1.396,0.469 1.396,0.469 1.167,0.469 true 1.146,1.74 1.417,1.74 1.417,1.74 1.417,1.115 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.615,0.229 2.146,0.5 0.531,0.271 10 false F127 0.74,0.406 1.24,0.625 0.5,0.219 10 false CA3H 0.76,1.667 1.25,1.885 0.49,0.219 10 false CA3L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F127-6 (CA3H) - F127-21 (CA3L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR