Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE UNIT › from 2016.11
RM3160E _51 Engine / Hybrid System _060157 2GR-FKS ENGINE MECHANICAL _0298899 ENGINE UNIT G

2GR-FKS ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A366101

Turn the roller by hand to check that it turns smoothly.

HINT:

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.



Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free from dirt and foreign matter.

·

Only use clean engine oil.



a.

Place the valve lash adjuster assembly into a container filled with engine oil.


b.
A286731C08
1.094,0.75 1.573,0.479 true 1.948,0.49 2.417,0.698 true 0.948,1.188 1.615,0.917 true 1.885,0.938 2.521,1.094 true 1.021,1.448 1.615,1.313 true 1.885,1.313 2.469,1.417 true 0.896,1.844 1.625,1.781 true 1.885,1.781 2.573,1.875 true 0.802,2.313 1.635,2.5 true 1.917,2.5 2.698,2.281 true 0.781,2.771 0.781,2.49 true 2.698,2.76 2.698,2.479 true 1.333,3.333 1.521,2.844 true 1.688,1.229 2,1.385 0.313,0.156 10 false *b 1.719,2.438 2.031,2.667 0.313,0.229 10 false *c 1.698,1.708 2.01,1.865 0.313,0.156 10 false *f 0.708,2.792 1.104,3.073 0.396,0.281 10 false *g 0.688,0.229 1,0.385 0.313,0.156 10 false *d 2.635,0.229 2.948,0.385 0.313,0.156 10 false *e 1.688,0.833 2,0.99 0.313,0.156 10 false *a 1.563,2.75 2.021,2.948 0.458,0.198 10 false SST 1.625,0.396 2.083,0.594 0.458,0.198 10 false SST 2.625,2.792 3.115,3.167 0.49,0.375 10 false *g
*a Tapered Path
*b Plunger
*c Check Ball
*d Correct
*e Incorrect
*f Low Pressure Chamber
*g High Pressure Chamber


Insert the tip of SST into the plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed any air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding the air from the high-pressure chamber, make sure that the tip of SST is pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.

OK:

Plunger is very difficult to move.


HINT:

If the plunger is easy to move, replace the valve lash adjuster assembly.



Hide 13511 3.INSPECT CAMSHAFT

a.

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.
A366102

Using a dial indicator, measure the runout at the center journal.

Maximum Runout:

0.04 mm (0.00157 in.)


HINT:
·

If the runout is more than the maximum, replace the camshaft.

·

Check the oil clearance after replacing the camshaft.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION





b.
A366103

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:
Item Specified Condition
Intake camshaft 44.335 to 44.435 mm (1.74547 to 1.74941 in.)
Exhaust camshaft 43.866 to 43.966 mm (1.72701 to 1.73094 in.)
Exhaust (for Fuel Pump) 40.554 to 40.654 mm (1.59661 to 1.60055 in.)


Minimum Cam Lobe Height:
Item Specified Condition
Intake camshaft 44.235 mm (1.74154 in.)
Exhaust camshaft 43.766 mm (1.72307 in.)
Exhaust (for Fuel Pump) 40.454 mm (1.59268 in.)


HINT:

If the cam lobe height is less than the minimum, replace the camshaft.



c.
A366104

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 35.946 to 35.960 mm (1.41519 to 1.41575 in.)
Other journals 25.959 to 25.975 mm (1.02201 to 1.02264 in.)


HINT:

If the journal diameter is not as specified, check the oil clearance.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION



Hide 11101A 4.INSPECT CYLINDER HEAD SET BOLT

a.
A366111C01
2.115,0.5 2.427,0.656 0.313,0.156 10 false *a 1.458,1.469 1.771,1.625 0.313,0.156 10 false *b
*a Measurement Point
*b 100 mm


Using a vernier caliper, measure the diameter of the threads at the measurement point.

Standard Diameter:

10.85 to 11.00 mm (0.427 to 0.433 in.)


Minimum Diameter:

10.70 mm (0.421 in.)


Measurement Point (Distance from the Seat):

100 mm (3.94 in.)


HINT:
·

If the diameter is less than the minimum, replace the cylinder head set bolt. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the cylinder head set bolt with a new one.




Hide 13506 5.INSPECT CHAIN SUB-ASSEMBLY

a.
A386378C14
1.729,0.979 2.042,1.177 0.313,0.198 10 false *a 0.979,2.01 1.188,2.177 0.208,0.167 10 false 0 1.385,2 1.583,2.177 0.198,0.177 10 false 1 1.99,2.021 2.313,2.177 0.323,0.156 10 false 14 2.396,2.01 2.667,2.177 0.271,0.167 10 false 15
*a Measurement Length


Using a spring scale, pull the chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

137.8 mm (5.43 in.)


HINT:
·

Perform the measurement at 3 random places. Use the average of the measurements.

·

If the average elongation is more than the maximum, replace the chain sub-assembly.




Hide 13507 6.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.
A386378C15
1.667,1.01 1.979,1.208 0.313,0.198 10 false *a 0.958,2.021 1.323,2.177 0.365,0.156 10 false 0 1.333,2 1.594,2.177 0.26,0.177 10 false 1 1.979,2.021 2.375,2.177 0.396,0.156 10 false 14 2.396,2 2.75,2.177 0.354,0.177 10 false 15
*a Measurement Length


Using a spring scale, pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

137.8 mm (5.43 in.)


HINT:
·

Perform the measurement at 3 random places. Use the average of the measurements.

·

If the average elongation is more than the maximum, replace the No. 2 chain sub-assembly.




Hide 13521 7.INSPECT CRANKSHAFT TIMING SPROCKET

a.

Place the chain sub-assembly around the crankshaft timing sprocket.


b.
A366112

Using a vernier caliper, measure the diameter of the crankshaft timing sprocket with the chain sub-assembly.

Maximum Sprocket Diameter (with Chain Sub-assembly):

62.2 mm (2.45 in.)


HINT:
·

The vernier caliper must contact the chain rollers when measuring.

·

If the diameter is more than the maximum, replace the chain sub-assembly and crankshaft timing sprocket.




Hide 13530 8.INSPECT IDLE SPROCKET ASSEMBLY

a.

Place the chain sub-assembly around the idle sprocket assembly.


b.
A366113

Using a vernier caliper, measure the diameter of the idle sprocket assembly with the chain sub-assembly.

Maximum Sprocket Diameter (with Chain Sub-assembly):

65.2 mm (2.57 in.)


HINT:
·

The vernier caliper must contact the chain rollers when measuring.

·

If the diameter is more than the maximum, replace the chain sub-assembly and idle sprocket assembly.




Hide 9.INSPECT NO. 1 IDLE GEAR SHAFT OIL CLEARANCE

a.
A366114

Using a micrometer, measure the diameter of the No. 1 idle gear shaft.

Standard No. 1 Idle Gear Shaft Diameter:

22.987 to 23.000 mm (0.905 to 0.906 in.)



b.
A366115

Using a caliper gauge, measure the inside diameter of the idle sprocket assembly.

Standard Idle Sprocket Assembly Inside Diameter:

23.020 to 23.030 mm (0.906 to 0.907 in.)



c.

Subtract the No. 1 idle gear shaft diameter measurement from the idle sprocket assembly inside diameter measurement.

Standard Oil Clearance:

0.020 to 0.043 mm (0.000787 to 0.00169 in.)


Maximum Oil Clearance:

0.093 mm (0.00366 in.)


HINT:

If the oil clearance is more than the maximum, replace the No. 1 idle gear shaft and idle sprocket assembly.



Hide 13540 10.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A366116C01
1.594,1.604 1.906,1.948 true 2.156,1.073 2.646,0.698 true 2.708,0.563 3.021,0.719 0.313,0.156 10 false *a 1.958,1.906 2.271,2.063 0.313,0.156 10 false *b
*a Plunger
*b Stopper Plate


Turn the stopper plate clockwise to release the lock. Push the plunger and check that it moves smoothly.

HINT:

If the plunger does not move smoothly, replace the No. 1 chain tensioner assembly.



Hide 13550 11.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A366117C01
3.208,0.417 3.427,0.719 0.219,0.302 10 false *a
*a Depth


Check that the plunger moves smoothly.


b.

Using a vernier caliper, measure the wear depth of the No. 2 chain tensioner assembly.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 2 chain tensioner assembly.



Hide 13560A 12.INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A366118C01
3.208,0.406 3.427,0.719 0.219,0.313 10 false *a
*a Depth


Check that the plunger moves smoothly.


b.

Using a vernier caliper, measure the wear depth of the No. 3 chain tensioner assembly.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 3 chain tensioner assembly.



Hide 13559 13.INSPECT CHAIN TENSIONER SLIPPER

a.
A366119C01
3.167,0.875 3.427,1.208 0.26,0.333 10 false *a
*a Depth


Measure the wear depth of the chain tensioner slipper.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the chain tensioner slipper.



Hide 13561 14.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A366120C01
3.177,0.865 3.427,1.188 0.25,0.323 10 false *a
*a Depth


Using a vernier caliper, measure the wear depth of the No. 1 chain vibration damper.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 1 chain vibration damper.



Hide 13562 15.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A366121C01
2.104,0.854 2.417,1.01 0.313,0.156 10 false *a
*a Depth


Using a vernier caliper, measure the wear depth of the No. 2 chain vibration damper.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 2 chain vibration damper.



Hide 16.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Inspect the camshaft thrust clearance (for Bank 1).



iii.
A366122

Using a dial indicator, measure the thrust clearance while moving each camshaft back and forth.

Standard Thrust Clearance:

0.08 to 0.13 mm (0.00315 to 0.00512 in.)


Maximum Thrust Clearance:

0.18 mm (0.00709 in.)


HINT:
·

If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly.

·

If the thrust surface is damaged, replace the camshaft or No. 2 camshaft.





b.

Inspect the camshaft thrust clearance (for Bank 2).

i.

Install the No. 3 camshaft sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY


ii.

Install the No. 4 camshaft sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY


iii.

Using a dial indicator, measure the thrust clearance while moving each camshaft back and forth.

Standard Thrust Clearance:

0.08 to 0.13 mm (0.00315 to 0.00512 in.)


Maximum Thrust Clearance:

0.18 mm (0.00709 in.)


HINT:
·

If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly LH.

·

If the thrust surface is damaged, replace the No. 3 camshaft sub-assembly or No. 4 camshaft sub-assembly.





Hide 17.INSPECT CAMSHAFT OIL CLEARANCE

a.

for Bank 1:

i.

Clean the camshaft bearing caps, camshaft housing sub-assembly and camshaft journals.


ii.

Place the camshafts onto the camshaft housing sub-assembly.


iii.
A366123C01
1.792,1.188 2.333,0.833 true 2.365,0.729 2.677,0.885 0.313,0.156 10 true *a
*a Plastigage


Lay a strip of Plastigage across each camshaft journal.


iv.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY

NOTICE:

Do not turn the camshaft.




vi.
A366124C01
1.813,1.219 2.323,0.844 true 3.01,4.052 2.667,2.604 2.667,2.604 3,3.292 true 0.875,3.313 1.604,2.625 1.604,2.625 2.323,3.292 true 1.625,4.063 1.365,4.479 1.365,4.479 2.344,4.052 true 0.875,4.031 1.375,4.479 1.375,4.479 0.469,4.031 true 1.604,3.344 1.604,2.646 true 2.375,0.74 2.688,0.896 0.313,0.156 10 true *a 2.563,2.427 2.875,2.583 0.313,0.156 10 false *b 1.313,4.49 1.625,4.646 0.313,0.156 10 false *c 1.521,2.448 1.833,2.604 0.313,0.156 10 false *c
*a Plastigage
*b No. 1 Journal
*c Other Journals


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 journal 0.032 to 0.063 mm (0.00126 to 0.00248 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 journal 0.10 mm (0.00394 in.)
Other journals 0.10 mm (0.00394 in.)


HINT:
·

If the oil clearance is more than the maximum, replace the camshaft or No. 2 camshaft.

·

If necessary, replace the camshaft housing sub-assembly.





b.

for Bank 2:

i.

Clean the camshaft bearing caps, camshaft housing sub-assembly LH and camshaft journals.


ii.

Place the camshafts on the camshaft housing sub-assembly LH.


iii.
A366125C01
1.25,0.938 1.563,0.427 true 1.125,0.969 1.438,1.125 0.313,0.156 10 true *a
*a Plastigage


Lay a strip of Plastigage across each camshaft journal.


iv.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY

NOTICE:

Do not turn the camshaft.



v.

vi.
A366126C01
1.281,0.948 1.563,0.51 true 0.521,3.823 0.875,3.49 0.875,3.49 0.51,3.135 true 2.781,3.135 2.083,2.552 2.083,2.552 1.375,3.135 true 2.083,3.083 2.083,2.573 true 2.792,3.802 2.094,4.375 2.094,4.375 1.385,3.802 true 2.094,4.354 2.094,3.844 true 1.167,0.979 1.479,1.135 0.313,0.156 10 true *a 0.938,3.427 1.25,3.583 0.313,0.156 10 false *b 2.01,2.354 2.323,2.51 0.313,0.156 10 false *c 2.021,4.406 2.333,4.563 0.313,0.156 10 false *c
*a Plastigage
*b No. 1 Journal
*c Other Journals


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 journal 0.032 to 0.063 mm (0.00126 to 0.00248 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 journal 0.10 mm (0.00394 in.)
Other journals 0.10 mm (0.00394 in.)


HINT:
·

If the oil clearance is more than the maximum, replace the No. 3 camshaft sub-assembly or No. 4 camshaft sub-assembly.

·

If necessary, replace the camshaft housing sub-assembly LH.





Hide 17111 18.INSPECT INTAKE MANIFOLD

A366127C01
0.146,0.094 0.458,0.25 0.313,0.156 10 false *a 0.198,2.542 0.51,2.698 0.313,0.156 10 false *b
*a Cylinder Head Side
*b Surge Tank Side


a.

Cylinder head side:

i.

Using a precision straightedge and feeler gauge, check the surface which contacts the cylinder head sub-assembly and cylinder head LH for warpage.

Maximum Warpage:

0.1 mm (0.00394 in.)


HINT:

If the warpage is more than the maximum, replace the intake manifold.




b.

Surge tank side:

i.

Using a precision straightedge and feeler gauge, check the surface which contacts the intake air surge tank assembly for warpage.

Maximum Warpage:

0.1 mm (0.00394 in.)


HINT:

If the warpage is more than the maximum, replace the intake manifold.




Hide 17141 19.INSPECT EXHAUST MANIFOLD

a.
A366128

Using a precision straightedge and feeler gauge, check the surface which contacts the cylinder head sub-assembly and cylinder head LH for warpage.

Maximum Warpage:

0.7 mm (0.0276 in.)


HINT:

If the warpage is more than the maximum, replace the exhaust manifold.