Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE UNIT › from 2016.11
RM3160E _51 Engine / Hybrid System _060157 2GR-FKS ENGINE MECHANICAL _0298899 ENGINE UNIT A

2GR-FKS ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.
A366040

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly LH.


b.
A366042

Remove the oil filler cap gasket from the oil filler cap sub-assembly.


Hide 12204 3.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 11415 4.REMOVE TAPER SCREW PLUG

a.

w/ Taper screw plug:

i.
A366047

Remove the taper screw plug from the cylinder block sub-assembly.



Hide 11415 5.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

A366048

a.

Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.


b.

Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.


Hide 12315 7.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.
A392567

Remove the 7 bolts and front No. 1 engine mounting bracket LH from the timing chain cover assembly.


Hide 16261 8.REMOVE WATER BY-PASS HOSE

a.
A373574

Slide the 2 clips and remove the water by-pass hose from the water inlet pipe and water inlet with thermostat sub-assembly.


Hide 16031 9.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 15370 10.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)

Hide 15370 11.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)

Hide 15370 12.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)

Hide 15370 13.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

Hide 11401Q 14.REMOVE VVT SENSOR (for Intake Side of Bank 1)

Hide 11401M 15.REMOVE VVT SENSOR (for Exhaust Side of Bank 1)

Hide 11401M 16.REMOVE VVT SENSOR (for Intake Side of Bank 2)

Hide 11401M 17.REMOVE VVT SENSOR (for Exhaust Side of Bank 2)

Hide 19312 18.REMOVE CRANKSHAFT POSITION SENSOR PROTECTOR

Hide 11401G 19.REMOVE CRANKSHAFT POSITION SENSOR

Hide 15710 20.REMOVE OIL COOLER ASSEMBLY

Hide 16281 21.REMOVE NO. 4 WATER BY-PASS HOSE

a.
A366045

Slide the clip and remove the No. 4 water by-pass hose from the water inlet pipe.


Hide 16282 22.REMOVE NO. 5 WATER BY-PASS HOSE

a.
A366046

Slide the clip and remove the No. 5 water by-pass hose from the water outlet.


Hide 15767 23.REMOVE OIL COOLER PIPE

a.
A366050

Remove the 4 bolts, 3 nuts and oil cooler pipe with No. 1 oil cooler bracket and oil hole cover gasket from the cylinder block sub-assembly and oil pan sub-assembly.


b.
A366051

Remove the bolt, 2 nuts, oil cooler pipe and oil cooler gasket from the No. 1 oil cooler bracket.


c.
A366052

Remove the No. 2 cylinder block insulator and No. 3 cylinder block insulator from the cylinder block sub-assembly and oil pan sub-assembly.


Hide 89422 24.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 16331 25.REMOVE WATER OUTLET

a.
A392568C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 4 bolts, 2 nuts and water outlet from the cylinder head sub-assembly and cylinder head LH.


b.
A392569

Remove the 2 No. 2 water inlet housing gaskets from the water outlet.


Hide 11201 26.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A366056

Remove the 2 clips and No. 1 engine cover sub-assembly from the cylinder head cover sub-assembly.


b.
A366167

Remove the 13 bolts and cylinder head cover sub-assembly from the camshaft housing sub-assembly.


c.
A366058

Remove the camshaft bearing cap oil hole gasket from the camshaft bearing cap.


d.
A366062

Remove the 3 cylinder head cover gaskets from the cylinder head cover sub-assembly.


Hide 11202 27.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A366072

Remove the 2 No. 1 V-bank cover brackets from the cylinder head cover sub-assembly LH.


b.
A366169

Remove the 14 bolts and cylinder head cover sub-assembly LH from the camshaft housing sub-assembly LH.


c.
A366060

Remove the camshaft bearing cap oil hole gasket LH from the camshaft bearing cap.


d.
A366065

Remove the 3 No. 2 cylinder head cover gaskets from the cylinder head cover sub-assembly LH.


Hide 11193 28.REMOVE SPARK PLUG TUBE GASKET

a.
A366061C01
1.49,1.198 2.188,0.396 true 2.24,0.24 2.552,0.396 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver as shown in the illustration, deform each spark plug tube gasket inwards and remove the 6 spark plug tube gaskets from the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.


Hide 12101A 29.REMOVE OIL PAN DRAIN PLUG

a.
A366044

Remove the oil pan drain plug and oil pan drain plug gasket from the No. 2 oil pan sub-assembly.


Hide 15620 30.REMOVE OIL FILTER CAP ASSEMBLY

Hide 83530 31.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 12102A 32.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A366064

Remove the 15 bolts and 2 nuts from the No. 2 oil pan sub-assembly.


b.
A120816

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the oil pans.



Hide 15104 33.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A366066

Remove the 2 nuts and oil strainer sub-assembly from the timing chain cover assembly.


b.
A409029

Remove the oil strainer gasket from the oil strainer sub-assembly.


Hide 89491 34.REMOVE ENGINE OIL LEVEL SENSOR

Hide 15679 36.REMOVE OIL FILTER BRACKET CLIP

a.
A371785

Remove the oil filter bracket clip from the oil pan sub-assembly.


Hide 12121 37.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A366068

Remove the 8 bolts and No. 1 oil pan baffle plate from the crankshaft bearing cap set bolt.


Hide 11324 38.REMOVE TIMING CHAIN COVER PLATE

a.
A373575

Remove the 4 bolts, timing chain cover plate and timing chain cover gasket from the timing chain cover assembly.


Hide 11301C 39.REMOVE TIMING CHAIN CASE OIL SEAL

Hide 11310 40.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 16100 41.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A366158

Remove the 7 bolts, engine water pump assembly and water pump gasket from the timing chain cover assembly.


Hide 42.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.

Temporarily tighten the crankshaft pulley set bolt to the crankshaft.


b.
A371813C01
0.375,1.635 0.375,1.448 0.375,1.448 0.802,0.979 true 0.521,0.469 0.885,0.229 0.885,0.229 1.094,0.229 true 1.146,0.156 1.458,0.313 0.313,0.156 10 true *a 0.313,1.646 0.625,1.802 0.313,0.156 10 false *b
*a Center Line
*b Key Groove


Turn the crankshaft clockwise to align the timing mark of the crankshaft timing sprocket key chase position with the center line of the block bore (for Bank 1) (TDC / compression).


c.

Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are aligned with the timing marks of the camshaft bearing caps as shown in the illustration.

A366156C02
1.167,0.74 2.333,0.5 2.333,0.5 1.156,0.5 true 2.813,2.438 3.969,1.906 3.969,1.906 2.792,1.906 true 4.396,1.01 5.552,0.479 5.552,0.479 4.375,0.479 true 4.333,0.917 5.521,0.49 true 5.948,2.073 4.927,1.906 4.927,1.906 5.917,1.906 true 5.906,2.115 4.948,1.917 true 2.396,0.427 2.708,0.583 0.313,0.156 10 false *a 0.75,3.552 1.063,3.708 0.313,0.156 10 false *b 1.438,3.115 1.75,3.271 0.313,0.156 10 false *b 4.354,3.271 4.667,3.427 0.313,0.156 10 false *b 5.063,3.573 5.375,3.729 0.313,0.156 10 false *b 4.021,1.813 4.333,1.969 0.313,0.156 10 false *a 5.604,0.396 5.917,0.552 0.313,0.156 10 false *a 4.76,1.813 5.073,1.969 0.313,0.156 10 false *a
*a Timing Mark *b Viewpoint


NOTICE:
·

Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear assembly and each camshaft timing exhaust gear assembly.

·

If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.



HINT:
·

If not aligned, turn the crankshaft 1 revolution (360°) clockwise and align the timing marks as shown in the illustration.

·
A377836N01
1.344,0.021 1.51,0.177 0.167,0.156 10 true A 1.656,0.021 1.823,0.177 0.167,0.156 10 true B 1.948,0.021 2.115,0.177 0.167,0.156 10 true C 2.208,0.021 2.375,0.177 0.167,0.156 10 true D

For the camshaft or No. 3 camshaft sub-assembly:

Be sure to check the mark (A) at the point where the marks (B), (C) and (D) are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.




Hide 13540 43.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A366075C01
1,1.354 1.74,1.771 1.74,1.771 2.656,1.385 true 0.979,1.083 1.396,0.667 true 2.594,1.906 2.917,1.906 true 2.688,1.073 3.104,0.656 true 1.458,0.552 1.771,0.708 0.313,0.156 10 true *a 1.656,1.813 1.969,1.969 0.313,0.156 10 true *b 2.979,1.844 3.292,2 0.313,0.156 10 true *c 3.115,0.458 3.427,0.615 0.313,0.156 10 true *a
*a Plunger
*b Stopper Plate
*c Pin


Turn the stopper plate clockwise to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.


b.

Turn the stopper plate counterclockwise to set the lock, and insert a 1.0 mm (0.0394 in.) diameter pin into the hole of the stopper plate.


c.
A366155

Remove the 2 bolts and No. 1 chain tensioner assembly from the cylinder head sub-assembly.


Hide 13559 44.REMOVE CHAIN TENSIONER SLIPPER

a.
A373576

Remove the chain tensioner slipper from the cylinder block sub-assembly.


Hide 13506 45.REMOVE CHAIN SUB-ASSEMBLY

a.
A372414C01
0.573,0.292 1.365,0.292 true 0.49,0.458 0.49,1.448 true 0.906,0.896 0.906,1.438 true 1.417,0.219 1.729,0.375 0.313,0.156 10 true *a 0.427,1.469 0.74,1.625 0.313,0.156 10 false *b 0.146,0.021 0.458,0.271 0.313,0.25 10 true 10° 0.844,1.458 1.156,1.615 0.313,0.156 10 true *c
*a Center Line
*b Mark
*c Key Groove


Turn the crankshaft 10° counterclockwise to loosen the chain sub-assembly of the crankshaft timing sprocket.


b.

Remove the crankshaft pulley set bolt from the crankshaft.


c.
A366078

Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.


d.
A366079C01
0.031,0.031 0.583,0.427 0.552,0.396 12 true *A
*A for Bank 1


Turn the camshaft timing gear assembly on bank 1 clockwise (approximately 60°) so that it is positioned as shown in the illustration.

NOTICE:

Be sure to loosen the chain sub-assembly between the banks.



e.

Remove the chain sub-assembly from the engine assembly.


Hide 13530 46.REMOVE IDLE SPROCKET ASSEMBLY

a.
A366080

Using a 10 mm hexagon socket wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft from the cylinder block sub-assembly.


Hide 13561 47.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A366081

Remove the 2 bolts and No. 1 chain vibration damper from the cylinder head LH and cylinder block sub-assembly.


Hide 13562 48.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A366153

Remove the 2 No. 2 chain vibration dampers from the cylinder head LH and cylinder head sub-assembly.


Hide 13521 49.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A366053

Remove the crankshaft timing sprocket from the crankshaft.


Hide 13521A 50.REMOVE CRANKSHAFT TIMING GEAR KEY

a.
A366082

Remove the 2 crankshaft timing gear keys from the crankshaft.


Hide 13050 51.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)

a.
A366083C01
0.917,2.948 0.813,2.792 false 1.344,2.99 1.198,2.781 true 1.344,3.01 1.656,3.167 0.313,0.156 10 false *a 0.896,2.969 1.208,3.125 0.313,0.156 10 false *b 2.031,1.531 2.344,1.688 0.313,0.156 10 true *c
*a Pin
*b Plunger
*c Push


While raising the No. 2 chain tensioner assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the hole to secure the No. 2 chain tensioner assembly.


b.
A381372C01
1.177,0.094 1.49,0.292 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of camshaft, loosen the camshaft timing gear bolt of the camshaft timing gear assembly.

NOTICE:
·

Be careful not to damage the camshaft, camshaft housing sub-assembly or spark plug tube with wrench.

·

Do not loosen any other bolt. If any other bolt is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.

·

If the camshaft timing gear bolt has been struck or dropped, replace it.




c.
A381373C01
0.917,0.406 1.229,0.604 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of No. 2 camshaft, loosen the camshaft timing gear bolt of the camshaft timing exhaust gear assembly.

NOTICE:
·

Be careful not to damage the No. 2 camshaft, camshaft housing sub-assembly or spark plug tube with wrench.

·

Do not loosen any other bolt. If any other bolt is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.

·

If the camshaft timing gear bolt has been struck or dropped, replace it.




d.

Remove the 2 camshaft timing gear bolts, camshaft timing gear assembly and camshaft timing exhaust gear assembly together with the No. 2 chain sub-assembly.


Hide 13550 52.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A366085

Remove the bolt and No. 2 chain tensioner assembly from the camshaft housing sub-assembly.


Hide 53.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

a.
A366086C01
1.115,2.604 1.646,3.01 1.646,3.01 2.51,2.646 true 1.573,3.031 1.885,3.188 0.313,0.156 10 false *a 1.625,2.365 1.938,2.521 0.313,0.156 10 false *b 2.948,2.438 3.26,2.594 0.313,0.156 10 false *c
*a Straight Pin
*b Front View
*c 45°


Check that the camshaft and No. 2 camshaft are positioned as shown in the illustration.


b.
A366087N01
3.042,0.25 3.198,0.448 0.156,0.198 10 true 1 2.573,0.271 2.729,0.469 0.156,0.198 10 true 2 1.729,0.281 1.885,0.479 0.156,0.198 10 true 3 0.917,0.25 1.073,0.448 0.156,0.198 10 true 4 0.281,0.313 0.438,0.51 0.156,0.198 10 true 5 0.5,1.979 0.656,2.177 0.156,0.198 10 true 9 0.906,1.979 1.063,2.177 0.156,0.198 10 true 8 1.729,1.979 1.885,2.177 0.156,0.198 10 true 7 2.563,1.979 2.719,2.177 0.156,0.198 10 true 6

Uniformly loosen and remove the 9 bolts in several steps in the order shown in the illustration.


c.
A372419N01
3.198,0.74 3.354,0.938 0.156,0.198 10 true 1 3.063,0.167 3.219,0.365 0.156,0.198 10 true 2 2.906,1.313 3.063,1.51 0.156,0.198 10 true 3 0.26,1.927 0.417,2.125 0.156,0.198 10 true 4 0.24,0.042 0.396,0.24 0.156,0.198 10 false 5 0.104,1.063 0.26,1.26 0.156,0.198 10 false 6 2.813,1.875 2.969,2.073 0.156,0.198 10 false 7 2.677,0.135 2.833,0.333 0.156,0.198 10 false 8 2.656,1.354 2.813,1.552 0.156,0.198 10 true 9 1.719,1.958 2.031,2.156 0.313,0.198 10 true 10 2.063,1.323 2.375,1.521 0.313,0.198 10 true 12 1.719,0 2.031,0.198 0.313,0.198 10 true 11 0.865,1.906 1.177,2.104 0.313,0.198 10 true 13 0.865,0.083 1.177,0.281 0.313,0.198 10 false 14 0.781,1.375 1.094,1.573 0.313,0.198 10 true 15

Uniformly loosen and remove the 15 bolts in several steps in the order shown in the illustration.

NOTICE:

Make sure that the camshaft and No. 2 camshaft remain level while uniformly loosening the bolts.



d.
A372476

Remove the fuel pump lifter housing from the camshaft housing sub-assembly.


e.
A372477

Remove the 5 camshaft bearing caps from the camshaft housing sub-assembly.


f.
A366084

Remove the 2 oil control valve filters from the 2 camshaft bearing caps.


Hide 13511 54.REMOVE CAMSHAFT

a.

Remove the camshaft from the camshaft housing sub-assembly.


Hide 13512 55.REMOVE NO. 2 CAMSHAFT

a.

Remove the No. 2 camshaft from the camshaft housing sub-assembly.


Hide 11103 56.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A366089C01
0.458,2.854 1.885,4.365 1.885,4.365 2.802,2.354 true 1.885,4.344 1.667,3.583 true 1.823,4.417 2.135,4.573 0.313,0.156 10 false *a
*a Protective Tape


Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver with its tip wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.



Hide 13050 57.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)

a.
A366090C01
1.896,3 2.313,2.583 true 1.646,2.906 2.063,2.49 true 1.49,2.865 1.802,3.021 0.313,0.156 10 false *a 1.74,2.99 2.052,3.146 0.313,0.156 10 false *b 1.625,0.385 1.938,0.542 0.313,0.156 10 true *c
*a Pin
*b Plunger
*c Push


While pushing down the No. 3 chain tensioner assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the hole to secure the No. 3 chain tensioner assembly.


b.
A381374C01
1.583,0.292 1.896,0.49 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of No. 3 camshaft sub-assembly, loosen the camshaft timing gear bolt of the camshaft timing gear assembly.

NOTICE:
·

Be careful not to damage the No. 3 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with wrench.

·

Do not loosen any other bolt. If any other bolt is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.

·

If the camshaft timing gear bolt has been struck or dropped, replace it.




c.
A381375C01
1.969,0.542 2.281,0.74 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of No. 4 camshaft sub-assembly, loosen the camshaft timing gear bolt of the camshaft timing exhaust gear assembly.

NOTICE:
·

Be careful not to damage the No. 4 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with wrench.

·

Do not loosen any other bolt. If any other bolt is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.

·

If the camshaft timing gear bolt has been struck or dropped, replace it.




d.

Remove the 2 camshaft timing gear bolts, camshaft timing gear assembly and camshaft timing exhaust gear assembly together with the No. 2 chain sub-assembly.


Hide 13560A 58.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A366092

Remove the bolt and No. 3 chain tensioner assembly from the camshaft housing sub-assembly LH.


Hide 59.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

a.
A366093C01
1.083,2.615 1.74,2.979 1.74,2.979 2.344,2.646 true 1.667,3.01 1.979,3.167 0.313,0.156 10 false *a 1.667,2.396 1.979,2.552 0.313,0.156 10 false *b
*a Straight Pin
*b Front View


Check that the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly are positioned as shown in the illustration.


b.
A366094N01
2.885,1.594 3.042,1.792 0.156,0.198 10 true 1 2.094,1.573 2.25,1.771 0.156,0.198 10 true 2 1.281,1.583 1.438,1.781 0.156,0.198 10 true 3 0.396,1.469 0.552,1.667 0.156,0.198 10 true 4 2.833,0 2.99,0.198 0.156,0.198 10 false 5 2.177,0 2.333,0.198 0.156,0.198 10 true 6 1.396,0 1.552,0.198 0.156,0.198 10 true 7 0.625,0 0.781,0.198 0.156,0.198 10 true 8

Uniformly loosen and remove the 8 bolts in several steps in the order shown in the illustration.


c.
A372475N01
0.615,1.958 0.771,2.156 0.156,0.198 10 false 1 3.26,1.865 3.417,2.063 0.156,0.198 10 false 2 3.219,1.219 3.375,1.417 0.156,0.198 10 false 3 3.177,0 3.333,0.198 0.156,0.198 10 true 4 2.875,1.771 3.031,1.969 0.156,0.198 10 false 5 3.125,0.708 3.281,0.906 0.156,0.198 10 false 6 0.104,0.063 0.26,0.26 0.156,0.198 10 false 7 0.031,0.75 0.188,0.948 0.156,0.198 10 false 9 0.104,1.604 0.26,1.802 0.156,0.198 10 false 8 2.313,0 2.625,0.198 0.313,0.198 10 true 10 2,1.823 2.313,2.021 0.313,0.198 10 true 11 2.333,1.188 2.646,1.385 0.313,0.198 10 true 12 0.719,0 1.031,0.198 0.313,0.198 10 true 13 1.292,1.833 1.604,2.031 0.313,0.198 10 true 14 1.667,1.167 1.979,1.365 0.313,0.198 10 true 15

Uniformly loosen and remove the 15 bolts in several steps in the order shown in the illustration.

NOTICE:

Make sure that the No. 3 camshaft and No. 4 camshaft remain level while uniformly loosening the bolts.



d.
A373577

Remove the 5 camshaft bearing caps from the camshaft housing sub-assembly LH.


e.
A366088

Remove the 2 oil control valve filters from the 2 camshaft bearing caps.


Hide 13053 60.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

a.

Remove the No. 3 camshaft sub-assembly from the camshaft housing sub-assembly LH.


Hide 13054 61.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

a.

Remove the No. 4 camshaft sub-assembly from the camshaft housing sub-assembly LH.


Hide 11104A 62.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A366096C01
0.521,3.135 1.969,4.427 1.969,4.427 2.74,2.823 true 1.969,4.406 1.948,3.583 true 1.927,4.458 2.24,4.615 0.313,0.156 10 false *a
*a Protective Tape


Remove the camshaft housing sub-assembly LH by prying between the cylinder head LH and camshaft housing sub-assembly LH with a screwdriver with its tip wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head LH and camshaft housing sub-assembly LH.



Hide 13801 63.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A366073

Remove the 24 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly and cylinder head LH.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13750 64.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.
A366077

Remove the 24 valve lash adjuster assemblies from the cylinder head sub-assembly and cylinder head LH.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13716 65.REMOVE VALVE STEM CAP

a.
A366076

Remove the 24 valve stem caps from the cylinder head sub-assembly and cylinder head LH.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 82219A 66.REMOVE SENSOR WIRE

a.
A366091

Remove the 3 bolts and sensor wire from the cylinder head LH and cylinder block sub-assembly.


Hide 11381 67.REMOVE REAR ENGINE OIL SEAL RETAINER

a.
A366069

Remove the 6 bolts from the rear engine oil seal retainer.


b.
A366070C01
0.583,1.031 1.125,1.031 true 0.26,0.948 0.573,1.104 0.313,0.156 10 true *a
*a Protective Tape
V100135

Pry


Using a screwdriver with its tip wrapped with protective tape, pry out the rear engine oil seal retainer.

NOTICE:

Be careful not to damage the rear engine oil seal retainer.



Hide 11381A 68.REMOVE REAR ENGINE OIL SEAL

a.
A366071C01
0.729,0.552 1.365,1.323 true 0.865,1.688 0.531,1.927 0.531,1.927 2.073,1.927 true 0.583,0.375 0.896,0.531 0.313,0.156 10 false *a 0.344,1.854 0.656,2.01 0.313,0.156 10 false *b
*a Protective Tape
*b Wooden Block


Place the rear engine oil seal retainer on wooden blocks.


b.

Using a hammer and a screwdriver with its tip wrapped with protective tape, tap out the rear engine oil seal.

NOTICE:

Be careful not to damage the rear engine oil seal retainer.



Hide 11101 69.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A366097N01
0.458,0.198 0.615,0.396 0.156,0.198 10 true 1 2.563,1.865 2.719,2.063 0.156,0.198 10 true 2 0.479,1.854 0.635,2.052 0.156,0.198 10 true 3 2.573,0.219 2.729,0.417 0.156,0.198 10 true 4 1.167,1.844 1.323,2.042 0.156,0.198 10 true 5 1.875,0.219 2.031,0.417 0.156,0.198 10 true 6 1.885,1.844 2.042,2.042 0.156,0.198 10 true 7 1.177,0.208 1.333,0.406 0.156,0.198 10 true 8

Using a 10 mm bi-hexagon socket wrench, uniformly loosen the 8 cylinder head set bolts in the order shown in the illustration. Remove the 8 cylinder head set bolts and 8 cylinder head set plate washers.

NOTICE:
·

Be careful not to drop the cylinder head set plate washers into the cylinder head sub-assembly.

·

Warpage or cracking of the cylinder head sub-assembly may result from removing the cylinder head set bolts in the incorrect order.



HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the cylinder head sub-assembly from the cylinder block sub-assembly.


Hide 11102 71.REMOVE CYLINDER HEAD LH

a.
A366098N01
0.031,1.313 0.188,1.51 0.156,0.198 10 false 1 0.042,0.635 0.198,0.833 0.156,0.198 10 false 2

Uniformly loosen and remove the 2 bolts in several steps in the order shown in the illustration.


b.
A366099N01
0.719,0.083 0.875,0.281 0.156,0.198 10 true 1 1.417,0.083 1.573,0.281 0.156,0.198 10 true 8 2.125,0.083 2.281,0.281 0.156,0.198 10 true 6 2.844,0.073 3,0.271 0.156,0.198 10 true 4 0.698,1.74 0.854,1.938 0.156,0.198 10 true 3 1.417,1.729 1.573,1.927 0.156,0.198 10 true 5 2.146,1.729 2.302,1.927 0.156,0.198 10 true 7 2.865,1.75 3.021,1.948 0.156,0.198 10 true 2

Using a 10 mm bi-hexagon socket wrench, uniformly loosen the 8 cylinder head set bolts in the order shown in the illustration. Remove the 8 cylinder head set bolts and 8 cylinder head set plate washers.

NOTICE:
·

Be careful not to drop the cylinder head set plate washers into the cylinder head LH.

·

Warpage or cracking of the cylinder head LH may result from removing the cylinder head set bolts in the incorrect order.



HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



c.

Remove the cylinder head LH from the cylinder block sub-assembly.


Hide 11116 72.REMOVE NO. 2 CYLINDER HEAD GASKET

Hide 16322 73.REMOVE WATER INLET PIPE

a.
A396110

Remove the 2 bolts and water inlet pipe from the cylinder block sub-assembly.


Hide 11114A 74.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


Hide 11151A 75.REMOVE CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the camshaft bearing cap setting ring pins unless they are being replaced.


Hide 76.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.