Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P033511  Crankshaft Position Sensor "A" Circuit Short to Ground  P033515  Crankshaft Position Sensor "A" Circuit Short to Battery or Open  P03351F  Crankshaft Position Sensor "A" Circuit Intermittent  P03352A  Crankshaft Position Sensor "A" Signal Stuck in Range  P033531  Crankshaft Position Sensor "A" No Signal  


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and Magneto Resistance Element (MRE) type sensor. The crankshaft position sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the NE signal to detect the crankshaft position and engine speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P033511 Crankshaft Position Sensor "A" Circuit Short to Ground The crankshaft position sensor output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored SAE Code: P0337
P033515 Crankshaft Position Sensor "A" Circuit Short to Battery or Open The crankshaft position sensor output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored SAE Code: P0338
P03351F Crankshaft Position Sensor "A" Circuit Intermittent Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed is 1000 rpm or more.
(b) Starter signal is off.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

ECM


Does not come on DTC stored SAE Code: P0339
P03352A Crankshaft Position Sensor "A" Signal Stuck in Range No crankshaft position sensor signal to the ECM while cranking (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

ECM


Comes on DTC stored SAE Code: P0335
P033531 Crankshaft Position Sensor "A" No Signal The engine stalls and the engine speed signal value decreases rapidly (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

ECM


Comes on DTC stored SAE Code: P0335

A200774E03
2.969,1.177 3.396,1.438 0.427,0.26 10 GND 0.083,0.073 0.698,0.292 0.615,0.219 10 2 V/DIV. 1.229,1.875 2.25,2.104 1.021,0.229 10 20 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:

The correct waveform is as shown.


ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

A DTC will be stored if any of the following occurs:

·

The crankshaft position sensor signal (NE signal) is not received by the ECM when the engine is being cranked.

·

The crankshaft position sensor signal (NE signal) is not received by the ECM when the engine is running.

·

The engine stalls and the engine speed signal value decreases rapidly (under normal conditions the engine speed will decrease gradually).

·

The crankshaft position sensor output voltage is above or below the threshold.


MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Required Sensors/Components (Related) VVT sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more [A].

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P033511, P033515, P03351F, P03352A or P033531.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A399932E01
2.01,0.448 2.323,0.646 0.313,0.198 10 false VC 2.302,0.458 2.583,0.792 0.281,0.333 10 false 3 1.938,0.979 2.396,1.177 0.458,0.198 10 false NE+ 2.302,0.979 2.458,1.177 0.156,0.198 10 false 1 1.958,1.542 2.417,1.74 0.458,0.198 10 false NE- 2.313,1.521 2.469,1.719 0.156,0.198 10 false 2 1.01,2.135 1.323,2.333 0.313,0.198 10 false Z5 0.99,2.313 2.885,2.594 1.896,0.281 10 false Crankshaft Position Sensor 4.604,0.438 4.833,0.719 0.229,0.281 10 false 96 4.865,0.448 5.396,0.75 0.531,0.302 10 false VCNE 4.51,0.979 4.969,1.177 0.458,0.198 10 false 128 4.875,0.969 5.333,1.167 0.458,0.198 10 false NE+ 4.583,1.5 4.896,1.698 0.313,0.198 10 false 95 4.875,1.531 5.333,1.729 0.458,0.198 10 false NE- 5.594,0.271 6.052,0.469 0.458,0.198 10 false 5 V 4.99,2.271 5.302,2.469 0.313,0.198 10 false C1 5.292,2.271 5.844,2.521 0.552,0.25 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

(a)

Connect the GTS to the DLC3.

(b)

Start the engine.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

e.

Start the engine.


f.

Read the values displayed on the GTS while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)
A376492C38
0.26,1.042 0.625,1.302 0.365,0.26 1.958,1.167 2.448,1.76 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.375,1.073 0.688,1.271 0.313,0.198 10 false Z5 2.396,1.771 2.708,1.969 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Crankshaft Position Sensor)


a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Z5-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z5-1 (NE+) - C1-128 (NE+) Always Below 1 Ω
Z5-2 (NE-) - C1-95 (NE-) Always Below 1 Ω
Z5-1 (NE+) or C1-128 (NE+) - Body ground and other terminals Always 10 kΩ or higher
Z5-2 (NE-) or C1-95 (NE-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
B319222C07
2.208,1.583 2.5,1.844 0.292,0.26 10 false *a 0.469,1.781 0.781,1.979 0.313,0.198 10 false OK 2.667,1.781 2.979,1.979 0.313,0.198 10 false NG
*a Clearance


a.

Check the crankshaft position sensor installation condition.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF CRANKSHAFT POSITION SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF CRANKSHAFT POSITION SENSOR PLATE)
a.

Inspect the teeth of the No. 1 crankshaft position sensor plate.

OK:

No .1 crankshaft position sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

6.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P033511, P033515, P03351F, P03352A AND/OR P033531)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P033511, P033515, P03351F, P03352A AND/OR P033531)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P033511, P033515, P03351F, P03352A and/or P033531 is output B


HINT:

If the engine does not start, replace the ECM.




A

END

B

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z5-3 (VC) - C1-96 (VCNE) Always Below 1 Ω
Z5-3 (VC) or C1-96 (VCNE) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR