While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).
*1: w/o Smart Entry and Start System.
*2: w/ Smart Entry and Start System.
Refer to DTC P061512.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>P061512
Inspect the fuses for circuits related to this system before performing the following procedure.
Check if the engine can be cranked.
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Starter SW.
| Tester Display |
|---|
| Starter SW |
Check the value displayed on the GTS when the ignition switch is turned to ON and the engine is cranked.
| Condition | GTS Display (Starter SW) |
|---|---|
| Ignition switch ON | OFF |
| Cranking position | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST relay.
Click hereEngine / Hybrid System>2GR-FKS STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter assembly.
Click hereEngine / Hybrid System>2GR-FKS STARTING>STARTER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (ST relay) - C18-1 | Always | Below 1 Ω |
| 3 (ST relay) or C18-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ST relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) battery terminal - D2-1 | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (w/o Smart Entry and Start System) | A |
| OK (w/ Smart Entry and Start System) | B |
| NG | C |
A
B
C
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-9 (L) - 2 (ST relay) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>2GR-FKS STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F50-2 (ST2) -5 (ST relay) | Always | Below 1 Ω |
| F50-2 (ST2) or 5 (ST relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-9 (L) - 2 (ST relay) | Always | Below 1 Ω |
| F10-12 (STA) - 2 (ST relay) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the park/neutral position switch assembly.
for 2WD models: Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for AWD models: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/o Smart Entry and Start System) | A |
| OK (w/ Smart Entry and Start System) | B |
| NG | C |
A
B
C
for 2WD models: Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for AWD models: Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>2GR-FKS STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Disconnect the ignition switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F50-6 (ST1) - C14-4 (B) | Always | Below 1 Ω |
| F50-6 (ST1) - C1-106 (NSW) | Always | Below 1 Ω |
| F50-6 (ST1) or C14-4 (B) or C1-106 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (ST relay) - C14-9 (L) | Always | Below 1 Ω |
| 2 (ST relay) or C14-9 (L) or A43-43 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-9 (L) - A43-43 (STA) | Always | Below 1 Ω |
| C14-9 (L), A43-43 (STA), 2 (ST relay) or F10-12 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F10-10 (STAR) - C14-4 (B) | Always | Below 1 Ω |
| F10-10 (STAR) - C1-106 (NSW) | Always | Below 1 Ω |
| F10-10 (STAR), C14-4 (B) or C1-106 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Starter SW.
| Tester Display |
|---|
| Starter SW |
Check the value displayed on the GTS when the ignition switch is turned to ON and the engine is cranked.
| Condition | GTS Display (Starter SW) |
|---|---|
| Ignition switch ON | OFF |
| Cranking position | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG