Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2016.11
RM3160E _55 Steering _019697 POWER ASSIST SYSTEMS _0104490 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  EPS Warning Light Circuit  


DESCRIPTION

If the power steering ECU assembly detects a malfunction, the EPS warning light comes on. At this time, the power steering ECU assembly stores a DTC in its memory.

WIRING DIAGRAM

C250102E35
0.854,0.646 1.292,0.896 0.438,0.25 10 false CANH 0.875,1.281 1.302,1.552 0.427,0.271 10 false CANL 5.969,0.656 6.438,0.948 0.469,0.292 10 false CANH 5.99,1.281 6.396,1.594 0.406,0.313 10 false CANL 1.333,0.479 1.604,0.802 0.271,0.323 10 false 28 1.344,1.104 1.552,1.385 0.208,0.281 10 false 27 0.271,1.781 0.708,2.031 0.438,0.25 10 false F126 0.271,1.938 2.156,2.135 1.885,0.198 10 false Combination Meter Assembly 1,4.354 2.625,4.635 1.625,0.281 10 false CAN Communication Line 4.052,0.625 4.417,0.948 0.365,0.323 10 false pF1 4.052,1.26 4.365,1.594 0.313,0.333 10 false pF1 4.052,2.406 4.417,2.719 0.365,0.313 10 false pF1 5.667,0.438 5.865,0.583 0.198,0.146 10 false 4 5.667,1.073 5.885,1.219 0.219,0.146 10 false 8 5.99,2.427 6.302,2.781 0.313,0.354 10 false IG 5.979,3.26 6.406,3.51 0.427,0.25 10 false PGND 5.656,3.042 5.75,3.198 0.094,0.156 10 false 2 5.177,3.958 7.146,4.292 1.969,0.333 10 false Power Steering ECU Assembly 2.615,2.594 3.5,2.74 0.885,0.146 10 false EPS-IG 0.229,2.417 1.646,2.76 1.417,0.344 10 false from IG1 NO. 2 Relay 4.125,2.229 4.313,2.49 0.188,0.26 10 false 5 5.656,2.219 5.875,2.365 0.219,0.146 10 false 1 5.625,3.208 5.854,3.542 0.229,0.333 10 false p2 5.635,2.396 5.854,2.708 0.219,0.313 10 false p1 5.635,1.26 5.833,1.552 0.198,0.292 10 false p1 5.635,0.625 5.833,0.948 0.198,0.323 10 false p1 4.135,1.063 4.292,1.25 0.156,0.188 10 false 2 4.115,0.438 4.271,0.625 0.156,0.188 10 false 1 4.958,2.542 5.292,2.76 0.333,0.219 10 false * 4.938,0.76 5.271,0.979 0.333,0.219 10 false * 4.948,1.396 5.281,1.615 0.333,0.219 10 false * 4.365,3.354 4.698,3.573 0.333,0.219 10 false * 0.49,4.021 2.646,4.302 2.156,0.281 10 false *: ECU Wire Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK ASSIST LIMIT RECORD
a.

Using the GTS, read the Data List item "Assist Limit Record 1".

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Assist Limit Record 1 Information of assist limit that was used in the past or is currently in use (latest history) Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, Vhcl Spd Sig Malf, Batt Vol Keep - -
Chassis > EMPS > Data List
Tester Display
Assist Limit Record 1
50003 142 73
HINT:

For the Data List item "Assist Limit Record 1", each item in the Range is described below.

Range Description
Mtr Overheat When the vehicle is stopped or traveling at low speed, and steering operations are performed repeatedly or the steering wheel is turned all the way to the side and held there for a long time, assist may be limited in order to prevent overheating of the power steering motor assembly and power steering ECU assembly.
After 10 minutes elapse with the engine stopped and no steering operations being performed, the system will return to normal.
After recovering from the overheated condition, assist can be performed as usual.
Pow Vol Low When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be stopped.
After the battery condition returns to normal, assist can be performed as usual.
Pow Vol Low Prevent When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be limited.
After the battery condition returns to normal, assist can be performed as usual.
Eng Stall When the engine stalls, battery charge becomes insufficient, so assist is stopped.
After recovering from the engine stall, assist can be performed as usual.
Ready OFF After Ready ON, if a malfunction in the HV system etc. causes a return to Ready OFF, the HV battery charge becomes insufficient, so assist is stopped.
After returning to Ready ON state, assist can be performed as usual.
Mtr Overload When the steering wheel cannot turn, such as when a road wheel is against a curb, if the driver continues to apply force to the steering wheel, current to the motor may be limited to prevent overheating.
When the steering wheel is returned to a neutral position, assist can be performed as usual.
DC-DC Malf If there is a malfunction in the DC-DC converter, etc., assist may be limited.
After the DC-DC converter returns to normal, assist can be performed as usual.
Vhcl Spd Sig Malf If the vehicle speed signal is abnormal due to a wheel speed sensor malfunction, etc., assist may be limited.
Batt Vol Keep When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be limited.
After the battery condition returns to normal, assist can be performed as usual.



b.

Based on the "Assist Limit Record 1" information, the following Data List items and the information from the customer interview, explain the situation to the customer.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Record 1 Key Cycle Number of times that the ignition switch was turned ON before Assist Limit Record 1 was stored Min.: 0 times
Max.: 65535 times
- -
Record 1 Key Cycle Elapsed Time Period of time that elapsed after the ignition switch was turned ON before Assist Limit Record 1 was stored Min.: 0.0 s
Max.: 53687091.1 s
- -
Chassis > EMPS > Data List
Tester Display
Record 1 Key Cycle
Record 1 Key Cycle Elapsed Time
50003 142 74,75
Result:
Result Proceed to
"Unrec" is displayed A
Other than Unrec is displayed B


HINT:

If it is necessary to investigate further into the past, check the "Assist Limit Record 2" and "Assist Limit Record 3" information in the same way as "Assist Limit Record 1".




A

2.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE

B

EXPLAIN THE CHECKED "ASSIST LIMIT RECORD 1" TO THE CUSTOMER, CROSS-CHECKING THE DATA LIST ITEMS WITH THE INFORMATION FROM THE CUSTOMER INTERVIEW.

2.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

OK:

The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

3.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

3.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

4.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)

B

4.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
a.
C295176C01
0.542,0.521 0.896,0.813 0.354,0.292 1.906,1.375 2.323,1.375 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 2.365,1.292 2.677,1.49 0.313,0.198 10 false IG 0.604,0.573 0.917,0.771 0.313,0.198 10 false pF1
*a Front view of wire harness connector
(to ECU Wire Sub-assembly)


Disconnect the pF1 ECU wire sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
pF1-5 (IG) - Body ground Ignition switch ON 9 to 16 V



Result:
Proceed to
OK
NG



OK

5.CHECK ECU WIRE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK ECU WIRE SUB-ASSEMBLY
a.
C240351C10
0.344,3.271 0.792,3.552 0.448,0.281 0.604,0.906 1.052,1.188 0.448,0.281 2.271,3.531 2.354,4.135 false 1.115,1.677 1.49,1.802 false 0.198,0.146 0.635,0.458 0.438,0.313 10 false *a 0.5,3.323 0.938,3.719 0.438,0.396 10 false p2 2.177,4.177 2.906,4.51 0.729,0.333 10 false PGND 0.917,1.583 1.344,1.948 0.427,0.365 10 false IG 0.771,0.958 1.156,1.344 0.385,0.385 10 false p1
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the pF1 connector to the ECU wire sub-assembly.


b.

Disconnect the p1 and p2 power steering ECU assembly connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
p1-1 (IG) - Body ground Ignition switch ON 9 to 16 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
p2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY

6.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the p1 and p2 power steering ECU assembly connectors.


b.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. EPS
50004 122 22

c.

Check the combination meter assembly.

OK:

The EPS warning light turns on or off in accordance with the GTS operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG