Refer to DTCs C1413 and C1414.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1413
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1405 | Open or Short in Front Speed Sensor RH Circuit | Either of the following is detected:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the +BS terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Front speed sensor RH ·
Speed sensor circuit ·
Skid control ECU (brake actuator assembly) |
| C1406 | Open or Short in Front Speed Sensor LH Circuit | Either of the following is detected:
1.
An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2.
With the +BS terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more. |
·
Front speed sensor LH ·
Speed sensor circuit ·
Skid control ECU (brake actuator assembly) |
DTC C1405 is for the front speed sensor RH.
DTC C1406 is for the front speed sensor LH.
Refer to DTCs C1413 and C1414.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1413
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open detection | Error or Normal | Error: Momentary interruption
Normal: Normal |
- |
| Tester Display |
|---|
| FR Speed Sensor Voltage Open |
| FL Speed Sensor Voltage Open |
There are no momentary interruptions.
Perform the above inspection before removing the sensor and connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the GTS to the DLC3.
Start the engine.
Select the Data List using the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
Check the speed value output from the speed sensor displayed on the GTS.
Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Perform a road test.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs C1405 and C1406 are not output. | A |
| DTCs C1405 and/or C1406 are output. | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A86 skid control ECU (brake actuator assembly) connector.
Disconnect the A35 or A34 front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A86-31 (FR+) - A35-2 (FR+) | Always | Below 1 Ω |
| A86-31 (FR+) or A35-2 (FR+) - Body ground | Always | 10 kΩ or higher |
| A86-30 (FR-) - A35-1 (FR-) | Always | Below 1 Ω |
| A86-30 (FR-) or A35-1 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A86-18 (FL+) - A34-2 (FL+) | Always | Below 1 Ω |
| A86-18 (FL+) or A34-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| A86-17 (FL-) - A34-1 (FL-) | Always | Below 1 Ω |
| A86-17 (FL-) or A34-1 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | RH |
| *B | LH |
| *a | Front view of wire harness connector
(to Front Speed Sensor) |
Reconnect the A86 skid control ECU (brake actuator assembly) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-2 (FR+) - Body ground | Ignition switch ON | 5.7 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-2 (FL+) - Body ground | Ignition switch ON | 5.7 to 14 V |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG