Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1427  Motor Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1427 Motor Malfunction Actuator pump motor does not operate properly.
·

Pump motor circuit

·

Ground circuit

·

Pump motor (brake actuator assembly)



HINT:

Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed:

1.

Drive the vehicle at 30 km/h (19 mph) for 30 seconds or more and check that the ABS warning light goes off.

2.

Clear the DTCs.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the pump motor (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ABS MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Active Test using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Motor Relay ABS motor relay Relay ON/OFF Operating sound of motor can be heard
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Motor Relay
50004 105 2

d.

Check the operating sound of the pump motor when operating it using the GTS.


Result:
Result Proceed to
Operating sound is heard. A
Operating sound is not heard. B



A

2.RECONFIRM DTC

B

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
2.RECONFIRM DTC
HINT:

This DTC is detected when a problem is identified in the skid control ECU (brake actuator assembly).

The ABS motor relay is in the skid control ECU (brake actuator assembly).

Therefore, ABS motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the skid control ECU (brake actuator assembly).


a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1427 is not output. A
DTC C1427 is output. B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch assembly off, the ECU performs self diagnosis of the pump motor circuit.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE





A

B

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
C364228C18
1.479,0.104 1.906,0.375 0.427,0.271 0.479,1.792 0.688,0.938 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false A86 0.344,1.844 0.802,2.042 0.458,0.198 10 false GND2 0.24,0.208 0.698,0.406 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-1 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)