The skid control ECU (brake actuator assembly) receives signals from the steering angle sensor via CAN communication.
If there is a malfunction in the bus lines between the steering angle sensor and the CAN communication system, DTCs U0073 (Control Module Communication Bus OFF), U0124 (Lost Communication with Lateral Acceleration Sensor Module) and/or U0126 (Lost Communication with Steering Angle Sensor Module) are output. When U0073, U0124 and/or U0126 are output together with C1434, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first.
DTCs may be stored if one of the following occurs:
Steering angle sensor zero point value malfunction.
Steering angle sensor signal malfunction.
Steering angle sensor installation abnormality.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1434 | Steering Angle Sensor Output Malfunction | Error in communication between the skid control ECU (brake actuator assembly) and the steering angle sensor, or abnormal steering angle sensor zero point. | ·
Sensor installation ·
Steering angle sensor power supply ·
Steering angle sensor |
Inspect the fuses for circuits related to this system before performing the following procedure.
When U0073, U0124 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073
When a speed sensor, or the yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal. When DTCs for a speed sensor, or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Start the engine.
Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left and then check that no speed sensor or yaw rate and acceleration sensor DTCs are output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output. | A |
| CAN communication system DTCs are output. | B |
| Speed sensor and/or yaw rate and acceleration sensor DTCs are output. | C |
If a speed sensor, or the yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal.
If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair these malfunctions and then inspect the steering angle sensor.
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Turn the ignition switch off.
Check that the steering angle sensor has been installed properly.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>INSTALLATION
The steering angle sensor installation is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Steering Angle Sensor) |
Remove the steering wheel and column cover.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the F58 steering angle sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F58-5 (BAT) - Body ground | Always | 11 to 14 V |
| F58-4 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Steering Angle Sensor) |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
Before measuring the resistance of the steering angle sensor, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F58-1 (ESS) - Body ground | 1 minute after turning ignition switch off | Below 1 Ω |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG