Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

EBD operation is not possible.

·

The brake booster assembly is judged to be defective.

·

Vacuum in the brake booster is insufficient (for 2GR-FKS).


WIRING DIAGRAM

C371800E01
1.458,0.49 2.073,0.688 0.615,0.198 10 false F126 3.708,0.479 4.323,0.677 0.615,0.198 10 false F126 3.698,0.948 4.313,1.146 0.615,0.198 10 false F126 1.49,0.99 1.948,1.188 0.458,0.198 10 false F21 1.531,0.281 1.844,0.479 0.313,0.198 10 false 17 1.521,0.781 1.833,0.979 0.313,0.198 10 false 12 3.781,0.26 4.094,0.458 0.313,0.198 10 false 28 3.781,0.75 4.094,0.948 0.313,0.198 10 false 27 1.854,1.281 3.75,1.531 1.896,0.25 10 false Combination Meter Assembly 1.885,0.49 2.5,0.688 0.615,0.198 10 false B/LE 1.885,0.99 2.344,1.188 0.458,0.198 10 false VCM 3.219,0.479 3.833,0.677 0.615,0.198 10 false CANH 3.24,0.958 3.854,1.156 0.615,0.198 10 false CANL 5.417,0.292 5.729,0.49 0.313,0.198 10 false 22 5.417,0.75 5.729,0.948 0.313,0.198 10 false 10 5.677,0.479 6.292,0.677 0.615,0.198 10 false CANH 5.677,0.948 6.292,1.146 0.615,0.198 10 false CANL 1.167,1.875 2.5,2.083 1.333,0.208 10 false from IG1 NO. 3 Relay 3.708,2.052 5.083,2.25 1.375,0.198 10 false IG1 NO. 2 3.76,1.75 3.917,1.948 0.156,0.198 10 false 1 4.167,1.75 4.323,1.948 0.156,0.198 10 false 2 5.417,1.75 5.729,1.948 0.313,0.198 10 false 12 5.677,1.885 6.135,2.083 0.458,0.198 10 false IG1 5.677,3.521 6.292,3.719 0.615,0.198 10 false GND1 5.417,3.396 5.729,3.594 0.313,0.198 10 false 25 1,4.083 1.458,4.281 0.458,0.198 10 false A89 1,4.24 3.323,4.406 2.323,0.167 10 false Vacuum Warning Switch Assembly* 1.427,3.635 1.583,3.833 0.156,0.198 10 false 2 1.615,3.729 1.771,3.927 0.156,0.198 10 false + 2.302,3.729 2.458,3.927 0.156,0.198 10 false E 2.5,3.635 2.656,3.833 0.156,0.198 10 false 1 1.167,3.052 1.323,3.25 0.156,0.198 10 false * 3.063,3.635 3.219,3.833 0.156,0.198 10 false * 5.177,4.333 5.635,4.531 0.458,0.198 10 false A86 5.167,4.5 6.76,4.854 1.594,0.354 10 false Skid Control ECU (Brake Actuator Assembly) 1.417,4.896 1.573,5.094 0.156,0.198 10 false 1 2.49,4.896 2.646,5.094 0.156,0.198 10 false 2 0.719,5.375 1.177,5.573 0.458,0.198 10 false A51 0.719,5.521 3.25,5.917 2.531,0.396 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly) 1.625,5.01 1.781,5.208 0.156,0.198 10 false + 2.292,5.021 2.448,5.219 0.156,0.198 10 false E 0.667,6.313 2.417,6.49 1.75,0.177 10 false : CAN Communication Line 4.625,5.615 6.771,5.813 2.146,0.198 10 false *: for 2GR-FKS

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin (w/ smart entry and start system).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Battery Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C364228C22
1.479,0.104 1.906,0.375 0.427,0.271 0.542,1.833 0.656,1.229 true 2.958,1.833 2.458,0.938 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false A86 0.385,1.875 0.844,2.073 0.458,0.198 10 false GND1 2.844,1.865 3.302,2.063 0.458,0.198 10 false IG1 0.219,0.167 0.677,0.365 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-12 (IG1) - Body ground Ignition switch ON 11 to 14 V
A86-12 (IG1) - A86-25 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C364228C15
1.479,0.104 1.906,0.375 0.427,0.271 0.542,1.833 0.656,1.229 true 1.583,0.156 2.042,0.354 0.458,0.198 10 false A86 0.385,1.875 0.844,2.073 0.458,0.198 10 false GND1 0.219,0.167 0.677,0.365 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-25 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.INSPECT BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
a.
C230719C10
1.99,1.979 2.458,2.771 true 1.479,1.979 1.021,2.771 true 0.365,0.302 0.594,0.49 0.229,0.188 10 false *a 2.427,2.792 2.583,2.979 0.156,0.188 10 false + 0.896,2.792 1.052,2.979 0.156,0.188 10 false E
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly))


Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A51 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.


Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - 2 (E) Brake fluid level warning switch off (Float up) 1.9 to 2.1 kΩ
1 (+) - 2 (E) Brake fluid level warning switch on (Float down) Below 1 Ω


HINT:

If the switch condition is normal, adjust the brake fluid level to the MAX level.



Result:
Result Proceed to
OK (for 1AR-FE) A
OK (for 2GR-FKS) B
NG C



A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY)

B

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY)

C

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY)
a.

Disconnect the F126 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F126-17 (B/LE) - A51-1 (+) Always Below 1 Ω
F126-17 (B/LE) or A51-1 (+) - Body ground Always 10 kΩ or higher
A51-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Reconnect the A51 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.


b.

Reconnect the F126 combination meter assembly connector.


c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light ON or OFF ON: Warning light on
OFF: Warning light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Brake Warning Light
50003 105 52

d.

Check the GTS display condition of the brake warning light.

Result:
Result Proceed to
Display of the Data List remains ON. A
Display of the Data List remains OFF. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY)
a.

Disconnect the F126 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F126-17 (B/LE) - A51-1 (+) Always Below 1 Ω
F126-17 (B/LE) or A51-1 (+) - Body ground Always 10 kΩ or higher
A51-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT VACUUM WARNING SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT VACUUM WARNING SWITCH ASSEMBLY
a.

Reconnect the A51 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.


b.

Reconnect the F126 combination meter assembly connector.


c.

Inspect the vacuum warning switch assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH>ON-VEHICLE INSPECTION

OK:

The vacuum warning switch assembly is normal.



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)

NG

REPLACE VACUUM WARNING SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)
a.

Disconnect the A89 vacuum warning switch assembly connector.


b.

Disconnect the F21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-12 (VCM) - A89-2 (+) Always Below 1 Ω
F21-12 (VCM) or A89-2 (+) - Body ground Always 10 kΩ or higher
A89-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Reconnect the A89 vacuum warning switch assembly connector.


b.

Reconnect the F21 combination meter assembly connector.


c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light ON or OFF ON: Warning light on
OFF: Warning light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Brake Warning Light
50003 105 52

d.

Check the GTS display condition of the brake warning light.

Result:
Result Proceed to
Display of the Data List remains ON. A
Display of the Data List remains OFF. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B