Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Downhill Assist Control Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

The downhill assist control indicator light comes on when the downhill assist control is ready. Even if the downhill assist control switch is pressed, the downhill assist control indicator light will blink and the downhill assist control will not be activated under the following conditions:

·

The shift lever is in any position other than S (1st) or R.

·

VSC system is malfunctioning.

·

Temperature of the brake actuator assembly increases and the downhill assist control is temporarily canceled.


WIRING DIAGRAM

C369734E01
5.969,0.927 6.583,1.125 0.615,0.198 10 false CANL 5.969,1.729 6.583,1.927 0.615,0.198 10 false CANH 5.677,0.729 6.292,0.927 0.615,0.198 10 false 10 5.688,1.542 6.302,1.74 0.615,0.198 10 false 22 5.969,2.875 6.583,3.198 0.615,0.323 10 false HDCS 5.698,2.729 6.313,2.927 0.615,0.198 10 false 27 3.531,3.385 5.635,3.75 2.104,0.365 10 false Downhill Assist Control Switch 3.531,3.219 4.146,3.417 0.615,0.198 10 false F41 3.99,3 4.604,3.198 0.615,0.198 10 false E 4.625,3 5.24,3.198 0.615,0.198 10 false B 4.854,2.74 5.469,2.938 0.615,0.198 10 false 4 3.781,2.75 4.385,3.031 0.604,0.281 10 false 1 2.938,4.333 5.042,4.698 2.104,0.365 10 false : CAN Communication Line 0.146,3.927 0.76,4.125 0.615,0.198 10 false F126 0.135,4.104 2.208,4.396 2.073,0.292 10 false Combination Meter Assembly 0.906,0.927 1.521,1.125 0.615,0.198 10 false CANL 0.906,1.74 1.521,1.938 0.615,0.198 10 false CANH 5.521,4.073 7.115,4.563 1.594,0.49 10 false Skid Control ECU (Brake Actuator Assembly) 5.531,3.917 6.146,4.24 0.615,0.323 10 false A86 1.396,1.542 1.938,1.854 0.542,0.313 10 false 28 1.396,0.719 1.938,1.031 0.542,0.313 10 false 27

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK DTC
a.

Check if ABS and/or VSC system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If the downhill assist control switch is turned on when ABS and/or VSC system DTCs are output, the downhill assist control indicator light blinks and the downhill assist control does not operate.



Result:
Result Proceed to
ABS and/or VSC system DTCs are not output. A
ABS and/or VSC system DTCs are output. B



A

2.CHECK DOWNHILL ASSIST CONTROL INDICATOR LIGHT

B

2.CHECK DOWNHILL ASSIST CONTROL INDICATOR LIGHT
a.

Interview the customer to check if the downhill assist control indicator light was blinking when the downhill assist control was operating.

HINT:
·

If the downhill assist control switch is turned on when the shift lever is in any position other than S (1st) or R, the downhill assist control indicator light blinks and the downhill assist control does not operate.

·

If the downhill assist control switch is turned on when the brake actuator assembly is hot, the downhill assist control indicator light blinks and the downhill assist control does not operate.



OK:

The downhill assist control indicator light does not blink.



Result:
Proceed to
OK
NG



OK

3.CHECK CAN COMMUNICATION SYSTEM

NG

END

3.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

4.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

4.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

5.CHECK BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

5.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Battery Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL SWITCH)

NG

6.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Downhill Assist Control SW Downhill assist control switch ON or OFF ON: Switch on
OFF: Switch off
for AWD
Chassis > ABS/VSC/TRC > Data List
Tester Display
Downhill Assist Control SW
50003 105 260

d.

Using the GTS, check the switch condition on the GTS changes according to downhill assist control switch operation.

OK:

The GTS display changes according to downhill assist control switch operation.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL INDICATOR LIGHT)

NG

8.INSPECT DOWNHILL ASSIST CONTROL SWITCH
7.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL INDICATOR LIGHT)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Downhill Assist Control Light Downhill assist control indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
for AWD
Chassis > ABS/VSC/TRC > Data List
Tester Display
Downhill Assist Control Light
50003 105 59

b.

Check the GTS display condition of the downhill assist control indicator light.

Result:
Result Proceed to
Display of the Data List remains ON. A
Display of the Data List remains OFF. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

8.INSPECT DOWNHILL ASSIST CONTROL SWITCH
a.
C296498C01
1.542,1.594 1.833,0.833 false 1.833,2.75 1.531,1.938 false 0.229,0.271 0.542,0.469 0.313,0.198 10 false *a 1.833,0.656 2.146,0.854 0.313,0.198 10 false B 1.823,2.792 2.135,2.99 0.313,0.198 10 false E
*a Component without harness connected
(Downhill Assist Control Switch)


Turn the ignition switch off.


b.

Disconnect the F41 Downhill assist control switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 1 (E) Downhill assist control switch pushed Below 1 Ω
4 (B) - 1 (E) Downhill assist control switch not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)

NG

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)
a.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-27 (HDCS) - F41-4 (B) Always Below 1 Ω
A86-27 (HDCS) or F41-4 (B) - Body ground Always 10 kΩ or higher
F41-1 (E) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR