Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2016.11
RM3160E _51 Engine / Hybrid System _060160 2GR-FKS INTAKE / EXHAUST _0299812 INTAKE MANIFOLD A

2GR-FKS INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55701J 5.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 22030 7.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 11209 8.REMOVE V-BANK COVER SUB-ASSEMBLY

Hide 47220D 9.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD)

Hide 47233 10.REMOVE RESERVOIR BRACKET (for RHD)

Hide 12261 11.DISCONNECT VENTILATION HOSE

a.
A395742

Slide the clip and disconnect the ventilation hose from the intake air surge tank assembly.


Hide 25860 12.DISCONNECT PURGE VALVE (PURGE VSV)

a.
A395743

Disconnect the No. 1 fuel vapor feed hose from the intake air surge tank assembly.


b.

Remove the bolt and disconnect the purge valve (purge VSV) from the intake air surge tank assembly.


Hide 17126 13.REMOVE NO. 2 SURGE TANK STAY

a.
A395745

Remove the 2 bolts and No. 2 surge tank stay from the intake air surge tank assembly and camshaft housing RH.


Hide 17190 14.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

a.
A395746

Disconnect the vacuum switching valve (for ACIS) connector.


b.

Disengage the 2 clamps to disconnect the vacuum hose sub-assembly from the intake air surge tank assembly.


c.
A395747C01
2.073,1.594 2.073,1.188 true 2.531,1.281 2.531,0.875 true 2.448,1.292 2.677,1.49 0.229,0.198 10 true *1 1.99,1.583 2.229,1.813 0.24,0.229 10 true *2
*1 Vacuum Hose Sub-assembly
*2 No. 2 Air Tube


Disengage the 2 clamps to disconnect the vacuum hose sub-assembly from the intake air surge tank assembly.


d.

Disengage the clamp to disconnect the No. 2 air tube from the intake air surge tank assembly.


e.
A395748C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 5 bolts, 2 nuts and intake air surge tank assembly from the intake manifold.


Hide 17176 15.REMOVE AIR SURGE TANK TO INTAKE MANIFOLD GASKET

a.
A370410

Remove the air surge tank to intake manifold gasket from the intake air surge tank assembly.


Hide 11254 16.REMOVE NO. 1 V-BANK COVER BRACKET

HINT:

Perform this procedure only when replacement of the No. 1 V-bank cover bracket is necessary.


a.
A370409

Remove the 2 No. 1 V-bank cover brackets from the intake air surge tank assembly.


Hide 12327A 17.REMOVE NO. 2 ENGINE MOUNTING STAY RH

a.
A395737C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, 2 nuts and No. 2 engine mounting stay RH from the engine moving control rod.


b.
A395749

Disengage the wire harness clamp from the wire harness clamp bracket.


c.
A395750

Remove the bolt and wire harness clamp bracket from the No. 2 engine mounting stay RH.


d.
A395751

Remove the bolt and No. 2 engine mounting stay RH from the intake manifold and engine mounting insulator sub-assembly RH.


Hide 23800 19.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

Hide 23807V 20.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23291 21.REMOVE INJECTOR VIBRATION INSULATOR

Hide 17111 22.REMOVE INTAKE MANIFOLD

a.
A395752C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 4 bolts, 4 nuts and intake manifold from the cylinder head sub-assembly.


Hide 17177 23.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.
A395753

Remove the 2 No. 1 intake manifold to head gaskets from each cylinder head sub-assembly.


Hide 24.REMOVE STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A370417

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the intake manifold.