Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0303262 AIR FUEL RATIO SENSOR A

2GR-FKS ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 1)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

for LHD

i.
A396309C01
1.104,1.563 1.573,1.563 true 1.656,0.365 1.896,0.573 0.24,0.208 10 true *a 1.604,1.469 2,1.667 0.396,0.198 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the exhaust manifold (TWC: Front Catalyst).

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




ii.

Engage the 3 wire harness clamps.


iii.

Connect the air fuel ratio sensor connector.



b.

for RHD

i.
A396424C01
1.479,1.604 1.479,1.063 true 2.427,0.552 2.74,0.708 0.313,0.156 10 false *a 1.385,1.604 1.844,1.802 0.458,0.198 10 false SST
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the exhaust manifold (TWC: Front Catalyst).

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)





Hide 17141 2.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst) (for RHD)

Hide 51442 3.INSTALL NO. 2 ENGINE UNDER COVER (for LHD)

Hide 89467C 4.INSTALL AIR FUEL RATIO SENSOR (for Bank 2)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A394316C01
1.771,2.708 2.396,2.708 true 2.083,0.688 2.323,0.896 0.24,0.208 10 true *a 1.417,2.625 1.76,2.844 0.344,0.219 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the exhaust manifold assembly LH (TWC: Front Catalyst).

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




b.

Connect the air fuel ratio sensor connector.


c.

Engage the 2 wire harness clamps.


Hide 11209 5.INSTALL V-BANK COVER SUB-ASSEMBLY

Hide 7.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing an air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION