Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › VALVE BODY ASSEMBLY(When Using the Engine Support Bridge) › from 2016.11
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0299917 VALVE BODY ASSEMBLY(When Using the Engine Support Bridge) A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY(When Using the Engine Support Bridge)  INSTALLATION  


PROCEDURE

Hide 35418 1.INSTALL MANUAL VALVE

a.

Coat the manual valve with ATF and install it to the transmission valve body assembly.


Hide 35148 2.INSTALL NO. 1 GOVERNOR APPLY GASKET

a.

Coat 2 new No. 1 governor apply gaskets with ATF.


b.

Install the 2 No. 1 governor apply gaskets to the automatic transaxle assembly.


Hide 35410 3.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.

Coat the O-ring of the transmission wire with ATF.


b.
C301124C01
2.438,0.427 2.625,0.427 2.625,0.427 2.792,0.844 true 2.573,0.156 2.76,0.156 2.76,0.156 2.969,0.76 true 1.729,0.479 1.958,0.771 0.229,0.292 10 false A 1.115,0.417 1.344,0.708 0.229,0.292 10 false B 0.771,0.417 1,0.708 0.229,0.292 10 false D 0.094,1.156 0.323,1.448 0.229,0.292 10 false C 0.104,2.031 0.333,2.25 0.229,0.219 10 false B 2.865,1.427 3.031,1.615 0.167,0.188 10 false B 0.698,2.625 0.927,2.917 0.229,0.292 10 false B 1.01,2.458 1.24,2.75 0.229,0.292 10 false A 1.417,2.417 1.646,2.708 0.229,0.292 10 false A 1.76,2.427 1.99,2.719 0.229,0.292 10 false A 2.125,2.458 2.354,2.75 0.229,0.292 10 false A 2.271,0.354 2.51,0.698 0.24,0.344 10 false *1 2.375,0.073 2.646,0.365 0.271,0.292 10 false *2 0.104,2.229 0.26,2.427 0.156,0.198 10 false *a 3.01,1.427 3.323,1.625 0.313,0.198 10 false *a
*1 Manual Valve Lever Shaft Sub-assembly
*2 Manual Valve
*a Positioning Bolt


Insert the pin of the manual valve lever shaft sub-assembly into the groove on the end of the manual valve and install the transmission valve body assembly to the automatic transaxle assembly with the 11 bolts.

Bolt Length
Bolt Length [mm (in.)]
(A) 25 (0.984)
(B) 30 (1.18)
(C) and (D) 35 (1.38)

Torque:
Bolt (A), (B), (C) : 10.8 N*m (110 kgf*cm, 8 ft.*lbf)
Bolt (D) : 9.6 N*m (98 kgf*cm, 85 in.*lbf)

NOTICE:
·

When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and automatic transaxle assembly to interfere with each other.

·

Be sure to insert the pin of the manual valve lever shaft sub-assembly into the groove on the end of the manual valve.

·

First, temporarily install the bolts marked (*a) in the illustration because they are positioning bolts.




Hide 35330 4.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.

Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted.



b.

Install the valve body oil strainer assembly to the transmission valve body assembly with the 2 bolts.

Torque:
9.6 N*m (98 kgf*cm, 85 in.*lbf)


Hide 35394 5.INSTALL TRANSMISSION OIL CLEANER MAGNET

a.
C306066C01
0.833,1.167 0.833,0.292 0.833,0.292 2.719,0.292 false 1.073,1.625 1.073,0.292 false 1.563,0.771 1.563,0.292 false 1.896,0.646 1.896,0.292 false 2.781,0.229 3.094,0.385 0.313,0.156 10 false *1
*1 Transmission Oil Cleaner Magnet


Install the 4 transmission oil cleaner magnets to the automatic transaxle oil pan sub-assembly as shown in the illustration.


Hide 35168A 6.INSTALL AUTOMATIC TRANSAXLE OIL PAN GASKET

a.

Install a new automatic transaxle oil pan gasket to the automatic transaxle oil pan sub-assembly.


Hide 35106D 7.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C298184

Clean and degrease the 2 bolts and installation holes in the automatic transaxle assembly.


b.
C312662

Install the automatic transaxle oil pan sub-assembly with automatic transaxle oil pan gasket to the automatic transaxle assembly with the 17 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

Completely remove any oil or grease from the contact surfaces of the automatic transaxle assembly and automatic transaxle oil pan sub-assembly with automatic transaxle oil pan gasket before installation.



c.
P000601C10
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 *1
*1 Adhesive 1324


Apply adhesive to 2 or 3 threads on the ends of the 2 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper installation of the 2 bolts, apply adhesive to the 2 bolts and install them within 10 minutes of adhesive application.



d.
C202903

Install the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 11.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION