Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM J

2GR-FKS ENGINE CONTROL  SFI SYSTEM  Pattern Select Switch Snow Mode Circuit  


DESCRIPTION

When SNOW mode is selected, the operation of the throttle motor is moderated to control engine output. This helps to reduce skidding of the drive wheels, and assists with takeoff acceleration, driving straightness and turning stability.

WIRING DIAGRAM

A306470E22
5.146,2.104 5.604,2.302 0.458,0.198 10 false C1 5.469,2.115 5.917,2.365 0.448,0.25 10 false ECM 4.948,0.844 5.406,1.042 0.458,0.198 10 false SNWI 4.625,0.729 5.083,0.927 0.458,0.198 10 false 105 1.792,1.24 2.25,1.438 0.458,0.198 10 false F42 2.073,1.24 4.083,1.75 2.01,0.51 10 false Pattern Select Switch Assembly (SNOW Mode Switch) 2.25,0.729 2.708,0.927 0.458,0.198 10 false 5 2.406,0.969 2.865,1.167 0.458,0.198 10 false E 2.917,0.969 3.375,1.167 0.458,0.198 10 false 2ND 3.292,0.719 3.75,0.917 0.458,0.198 10 false 8

PROCEDURE

1.READ VALUE USING GTS (SNOW MODE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Snow Mode SW.

Powertrain > Engine > Data List
Tester Display
Snow Mode SW
50003 372 23

d.

Read the value displayed on the GTS.

OK:
Condition GTS Display (Snow Mode SW)
SNOW mode switch pushed and held ON
SNOW mode switch not pushed OFF



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PATTERN SELECT SWITCH ASSEMBLY (SNOW MODE SWITCH)
2.INSPECT PATTERN SELECT SWITCH ASSEMBLY (SNOW MODE SWITCH)

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH ASSEMBLY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH ASSEMBLY - ECM)
a.

Disconnect the pattern select switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F42-8 (2ND) - C1-105 (SNWI) Always Below 1 Ω
F42-8 (2ND) or C1-105 (SNWI) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the pattern select switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F42-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR