Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1415  Rear Speed Sensor RH Output Malfunction  C1416  Rear Speed Sensor LH Output Malfunction  


DESCRIPTION

Each speed sensor detects wheel speed and sends signals to the skid control ECU (brake actuator assembly). These signals are used by the ABS.

The speed sensor rotors have rows of alternating N and S magnetic poles.

Hall IC type speed sensors use the frequency of output pulses to detect the vehicle speed. Because the sensor outputs digital pulses, it can detect the vehicle speed even when the vehicle is nearly stationary.

C269035E04
1.833,1.083 1.833,0.583 false 1.583,0.583 1.833,0.583 false 5,1.25 5,0.583 false 5,0.583 4.75,0.583 false 0.313,0.167 1.083,0.365 0.771,0.198 10 false for 2WD: 3.833,0.167 4.604,0.365 0.771,0.198 10 false for AWD: 0.667,0.5 1.74,0.698 1.073,0.198 10 false Speed Sensor 1.229,2.417 2.75,2.729 1.521,0.313 10 false Speed Sensor Rotor 4.833,3.385 5.448,3.583 0.615,0.198 10 false 1.4 V 4.833,3.75 5.448,3.948 0.615,0.198 10 false 0.7 V 3.698,4.198 4.594,4.531 0.896,0.333 10 false High speed 2.75,4.198 3.563,4.552 0.813,0.354 10 false Low speed 3.844,0.49 4.917,0.688 1.073,0.198 10 false Speed Sensor 4.583,2.427 6.104,2.74 1.521,0.313 10 false Speed Sensor Rotor

HINT:

Check the connection status between the sensor connector and the vehicle wire harness.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1415 Rear Speed Sensor RH Output Malfunction Any of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Sensor installation

·

for 2WD: Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

for AWD: Rear speed sensor RH

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Speed sensor circuit

·

Skid control ECU (brake actuator assembly)


C1416 Rear Speed Sensor LH Output Malfunction Any of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Sensor installation

·

for 2WD: Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

for AWD: Rear speed sensor LH

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)

·

Speed sensor circuit

·

Skid control ECU (brake actuator assembly)



HINT:

for C1415 and C1416: Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed.

1.

Drive the vehicle at 30 km/h (19 mph) for 30 seconds or more and check that the ABS warning light goes off.

2.

Clear the DTCs.


DTC C1415 is for the rear speed sensor RH.

DTC C1416 is for the rear speed sensor LH.


WIRING DIAGRAM

C265402E20
5.719,1.479 6,1.74 0.281,0.26 10 false 15 6.01,1.052 6.448,1.396 0.438,0.344 10 false RR+ 5.719,0.906 6.063,1.188 0.344,0.281 10 false 16 5.51,8.167 7.156,8.635 1.646,0.469 10 false Skid Control ECU (Brake Actuator Assembly) 5.51,7.979 5.958,8.25 0.448,0.271 10 false A86 6.01,1.615 6.469,1.927 0.458,0.313 10 false RR- 6.01,5.146 6.469,5.417 0.458,0.271 10 false RL+ 6.01,5.729 6.396,5.99 0.385,0.26 10 false RL- 5.729,5.01 5.99,5.292 0.26,0.281 10 false 29 5.729,5.573 5.979,5.802 0.25,0.229 10 false 28 1.177,1.5 1.396,1.719 0.219,0.219 10 false 1 1.188,0.948 1.469,1.188 0.281,0.24 10 false 2 0.135,2.052 0.667,2.365 0.531,0.313 10 false O3 0.417,2.052 1.156,2.5 0.74,0.448 10 false Rear Speed Sensor RH 0.823,1.052 1.271,1.344 0.448,0.292 10 false RR+ 0.823,1.625 1.406,1.948 0.583,0.323 10 false RR- 2.354,0.917 2.688,1.198 0.333,0.281 10 false *1 2.354,1.5 2.823,1.813 0.469,0.313 10 false *1 3.125,2.635 3.406,2.906 0.281,0.271 10 false *2 3.448,3.25 3.854,3.552 0.406,0.302 10 false *2 2,2.792 2.354,2.979 0.354,0.188 10 false RR+ 2,3.375 2.448,3.698 0.448,0.323 10 false RR- 1.594,2.792 2.188,3.135 0.594,0.344 10 false RR+ 1.594,3.375 1.99,3.604 0.396,0.229 10 false RR- 0.833,2.792 1.292,3.073 0.458,0.281 10 false RR+ 0.833,3.375 1.146,3.563 0.313,0.188 10 false RR- 1.271,2.771 1.677,3.083 0.406,0.313 10 false o1 1.271,3.354 1.573,3.635 0.302,0.281 10 false o1 2.385,2.771 2.823,3.031 0.438,0.26 10 false Oo1 2.375,3.354 2.781,3.635 0.406,0.281 10 false Oo1 1.302,2.594 1.604,2.896 0.302,0.302 10 false 2 2.458,2.583 2.781,2.875 0.323,0.292 10 false 2 1.302,3.177 1.49,3.385 0.188,0.208 10 false 1 2.448,3.167 2.823,3.479 0.375,0.313 10 false 1 0.385,3.781 1.135,4.208 0.75,0.427 10 false Rear Speed Sensor RH 1.49,3.792 2.802,4.198 1.313,0.406 10 false Skid Control Sensor Wire RH 1.188,5.042 1.385,5.292 0.198,0.25 10 false 3 1.188,5.604 1.469,5.875 0.281,0.271 10 false 1 0.115,6.167 0.521,6.438 0.406,0.271 10 false O2 0.406,6.167 1.156,6.563 0.75,0.396 10 false Rear Speed Sensor LH 0.844,5.156 1.396,5.427 0.552,0.271 10 false RL+ 0.844,5.729 1.406,6.021 0.563,0.292 10 false RL- 2.354,5.01 2.719,5.313 0.365,0.302 10 false *1 2.354,5.615 2.708,5.927 0.354,0.313 10 false *1 3.125,6.76 3.354,6.938 0.229,0.177 10 false *2 3.427,7.333 3.656,7.51 0.229,0.177 10 false *2 2,6.917 2.5,7.177 0.5,0.26 10 false RL+ 2,7.479 2.396,7.708 0.396,0.229 10 false RL- 1.594,6.917 2.083,7.177 0.49,0.26 10 false RL+ 1.594,7.479 1.948,7.698 0.354,0.219 10 false RL- 0.833,6.906 1.188,7.094 0.354,0.188 10 false RL+ 0.833,7.479 1.146,7.667 0.313,0.188 10 false RL- 1.281,6.885 1.625,7.146 0.344,0.26 10 false r1 1.281,7.469 1.646,7.76 0.365,0.292 10 false r1 2.396,6.885 2.813,7.125 0.417,0.24 10 false Or1 2.406,7.469 2.823,7.708 0.417,0.24 10 false Or1 1.302,6.698 1.51,6.906 0.208,0.208 10 false 2 2.458,7.271 2.813,7.552 0.354,0.281 10 false 1 1.302,7.281 1.563,7.531 0.26,0.25 10 false 1 2.458,6.688 2.813,7 0.354,0.313 10 false 3 0.375,7.896 1.115,8.302 0.74,0.406 10 false Rear Speed Sensor LH 1.448,7.896 2.75,8.406 1.302,0.51 10 false Skid Control Sensor Wire LH 3.104,8.01 3.885,8.198 0.781,0.188 10 false *1: for AWD 3.104,8.313 3.875,8.5 0.771,0.188 10 false *2: for 2WD

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open Rear speed sensor RH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Open Rear speed sensor LH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Result Proceed to
OK A
NG (for 2WD) B
NG (for AWD) C



A

2.READ VALUE USING GTS (REAR SPEED SENSOR)

B

4.CHECK REAR SPEED SENSOR INSTALLATION

C

8.CHECK REAR SPEED SENSOR INSTALLATION
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

e.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.



Result:
Result Proceed to
OK A
NG (for 2WD) B
NG (for AWD) C



A

3.RECONFIRM DTC

B

4.CHECK REAR SPEED SENSOR INSTALLATION

C

8.CHECK REAR SPEED SENSOR INSTALLATION
3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1415 and C1416 are not output. A
DTCs C1415 and/or C1416 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

4.CHECK REAR SPEED SENSOR INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor
*a Correct
*b Incorrect
*c No clearance


Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle carrier.



Result:
Proceed to
OK
NG



OK

5.INSPECT SKID CONTROL SENSOR WIRE

NG

5.INSPECT SKID CONTROL SENSOR WIRE
a.
C296046C01
0.844,2.667 1.167,2.833 0.323,0.167 0.854,0.333 1.177,0.5 0.323,0.167 2.344,0.583 2.667,0.75 0.323,0.167 2.219,2.833 2.542,3 0.323,0.167 0.5,1.833 0.5,1.5 0.5,1.5 0.906,1.135 false 0.5,4.25 0.5,3.833 0.5,3.833 0.917,3.448 false 2,1.833 2,1.583 2,1.583 2.302,1.333 false 1.917,4.25 1.917,3.917 1.917,3.917 2.167,3.615 false 1.583,1.833 1.583,1.5 1.583,1.5 1.156,1.135 false 1.5,4.25 1.5,3.833 1.5,3.833 1.177,3.448 false 3,1.833 3,1.583 3,1.583 2.698,1.344 false 2.917,4.25 2.917,3.917 2.917,3.917 2.635,3.604 false 1.49,1.865 1.948,2.063 0.458,0.198 10 false RR+ 1.917,1.865 2.375,2.063 0.458,0.198 10 false RR+ 2.917,1.875 3.375,2.073 0.458,0.198 10 false RR- 0.417,1.865 0.875,2.063 0.458,0.198 10 false RR- 0.427,4.292 0.885,4.49 0.458,0.198 10 false RL- 1.417,4.292 1.875,4.49 0.458,0.198 10 false RL+ 1.833,4.281 2.292,4.479 0.458,0.198 10 false RL+ 2.844,4.281 3.302,4.479 0.458,0.198 10 false RL- 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a 0.958,0.333 1.271,0.531 0.313,0.198 10 false o1 2.281,2.844 2.594,3.042 0.313,0.198 10 false Or1 0.958,2.667 1.271,2.865 0.313,0.198 10 false r1 2.385,0.583 2.698,0.781 0.313,0.198 10 false Oo1 0.177,0.51 0.49,0.708 0.313,0.198 12 false *A 0.188,2.802 0.5,3 0.313,0.198 12 false *B 0.927,1.948 1.24,2.146 0.313,0.198 10 false *b 2.417,1.948 2.729,2.146 0.313,0.198 10 false *c 0.938,4.365 1.25,4.563 0.313,0.198 10 false *b 2.323,4.365 2.635,4.563 0.313,0.198 10 false *c
*A RH
*B LH
*a Front view of Skid Control Sensor Wire
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Remove the skid control sensor wire.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
o1-2 (RR+) - Oo1-2 (RR+) Always Below 1 Ω
o1-2 (RR+) - Oo1-1 (RR-) Always 10 kΩ or higher
o1-2 (RR+) or Oo1-2 (RR+) - Body ground Always 10 kΩ or higher
o1-1 (RR-) - Oo1-1 (RR-) Always Below 1 Ω
o1-1 (RR-) - Oo1-2 (RR+) Always 10 kΩ or higher
o1-1 (RR-) or Oo1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
r1-2 (RL+) - Or1-3 (RL+) Always Below 1 Ω
r1-2 (RL+) - Or1-1 (RL-) Always 10 kΩ or higher
r1-2 (RL+) or Or1-3 (RL+) - Body ground Always 10 kΩ or higher
r1-1 (RL-) - Or1-1 (RL-) Always Below 1 Ω
r1-1 (RL-) - Or1-3 (RL+) Always 10 kΩ or higher
r1-1 (RL-) or Or1-1 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A86-16 (RR+) - Oo1-2 (RR+) Always Below 1 Ω
A86-16 (RR+) or Oo1-2 (RR+) - Body ground Always 10 kΩ or higher
A86-15 (RR-) - Oo1-1 (RR-) Always Below 1 Ω
A86-15 (RR-) or Oo1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A86-29 (RL+) - Or1-3 (RL+) Always Below 1 Ω
A86-29 (RL+) or Or1-3 (RL+) - Body ground Always 10 kΩ or higher
A86-28 (RL-) - Or1-1 (RL-) Always Below 1 Ω
A86-28 (RL-) or Or1-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C205828C05
0.75,0.906 1.083,1.083 0.333,0.177 2.354,0.906 2.688,1.083 0.333,0.177 1.094,1.823 1.417,2.417 false 2.667,1.76 3,2.417 false 0.104,0.073 0.292,0.26 0.188,0.188 10 false *a 0.802,0.906 1.333,1.177 0.531,0.271 10 false Oo1 2.417,0.906 2.917,1.198 0.5,0.292 10 false Or1 1.323,2.469 1.656,2.656 0.333,0.188 10 false RR+ 2.917,2.469 3.25,2.656 0.333,0.188 10 false RL+ 0.25,0.729 0.646,1.073 0.396,0.344 12 false *A 1.917,0.729 2.26,1.188 0.344,0.458 12 false *B
*A RH
*B LH
*a Front view of wire harness connector
(to Skid Control Sensor Wire)


Reconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
Oo1-2 (RR+) - Body ground Ignition switch ON 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
Or1-3 (RL+) - Body ground Ignition switch ON 5.7 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:
·

for 2WD: The rear speed sensor rotor and rear speed sensor are incorporated into the rear axle hub and bearing assembly.

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

NG

8.CHECK REAR SPEED SENSOR INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Rear Speed Sensor
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle carrier.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

9.CHECK REAR SPEED SENSOR AND SENSOR ROTOR

NG

9.CHECK REAR SPEED SENSOR AND SENSOR ROTOR
a.

Remove the rear speed sensor and the component with the sensor rotor.

for speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR(for AWD)>REMOVAL

for sensor rotor: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the speed sensor tip and speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the sensor tip and rotor.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

CLEAN OR REPLACE REAR SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
a.

Install the rear speed sensor and the component with the sensor rotor.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the O3 or O2 rear speed sensor connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A86-16 (RR+) - O3-2 (RR+) Always Below 1 Ω
A86-16 (RR+) or O3-2 (RR+) - Body ground Always 10 kΩ or higher
A86-15 (RR-) - O3-1 (RR-) Always Below 1 Ω
A86-15 (RR-) or O3-1 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A86-29 (RL+) - O2-3 (RL+) Always Below 1 Ω
A86-29 (RL+) or O2-3 (RL+) - Body ground Always 10 kΩ or higher
A86-28 (RL-) - O2-1 (RL-) Always Below 1 Ω
A86-28 (RL-) or O2-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C205828C04
0.75,0.906 1.083,1.083 0.333,0.177 2.354,0.906 2.688,1.083 0.333,0.177 1.094,1.823 1.417,2.417 false 2.667,1.76 3,2.417 false 0.104,0.073 0.292,0.26 0.188,0.188 10 false *a 0.823,0.906 1.354,1.177 0.531,0.271 10 false O3 2.427,0.906 2.927,1.198 0.5,0.292 10 false O2 1.323,2.469 1.656,2.656 0.333,0.188 10 false RR+ 2.917,2.469 3.25,2.656 0.333,0.188 10 false RL+ 0.25,0.729 0.646,1.073 0.396,0.344 12 false *A 1.917,0.729 2.26,1.188 0.344,0.458 12 false *B
*A RH
*B LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Reconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
O3-2 (RR+) - Body ground Ignition switch ON 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
O2-3 (RL+) - Body ground Ignition switch ON 5.7 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG