Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095462 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser system compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The immobiliser system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ECM, ID code box (immobiliser code ECU)*1, or certification ECU (smart key ECU assembly)*2, refer to Service Bulletin.

*1: w/ Rear Seat Heater

*2: w/o Rear Seat Heater


·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If a immobiliser system or SFI system DTC is output, first perform troubleshooting for the immobiliser system or SFI system DTC.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK WHETHER ENGINE STARTS

B

2.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

USE SIMULATION METHOD TO CHECK

NG

3.INSPECT ECM (TERMINAL IMI AND IMO)
3.INSPECT ECM (TERMINAL IMI AND IMO)
a.

Using an oscilloscope, check the waveform.

B352096C15
5.75,0.208 6.146,0.49 0.396,0.281 2.323,0.198 2.719,0.479 0.396,0.281 2.99,4.052 2.99,3.656 false 3.396,6.094 3.396,5.698 false 4.792,2.063 5.219,1.333 false 5.271,2.063 5.333,1.448 false 1.427,1.99 1.49,1.146 false 6.5,2.063 5.469,1.26 false 5.979,2.042 5.365,1.26 false 2.75,2.01 2.5,1.042 false 5.833,0.26 6.292,0.458 0.458,0.198 10 false A43 2.438,0.25 2.75,0.448 0.313,0.198 10 false C1 0.208,0.146 0.521,0.344 0.313,0.198 10 false *a 1.042,2.271 1.354,2.469 0.313,0.198 10 false *f 1.042,4.302 1.354,4.5 0.313,0.198 10 false *g 1.031,3.604 1.49,3.802 0.458,0.198 10 false GND 1.052,5.646 1.51,5.844 0.458,0.198 10 false GND 3.052,2.646 3.292,2.813 0.24,0.167 10 false *i 2.917,4.073 3.229,4.271 0.313,0.198 10 false *b 3.125,3.729 3.438,3.927 0.313,0.198 10 false *c 3.458,4.615 3.771,4.813 0.313,0.198 10 false *j 3.51,5.719 3.823,5.917 0.313,0.198 10 false *c 3.333,6.115 3.646,6.313 0.313,0.198 10 false *b 2.427,4.625 2.74,4.823 0.313,0.198 10 false *h 4.094,6.51 4.406,6.708 0.313,0.198 10 false *k 2.198,6.51 2.51,6.708 0.313,0.198 10 false *k 2.646,7.135 2.958,7.333 0.313,0.198 10 false *d 4.667,7.104 4.979,7.302 0.313,0.198 10 false *d 4.604,7.406 4.917,7.604 0.313,0.198 10 false *e 2.74,7.375 3.052,7.573 0.313,0.198 10 false *e 5.156,2.104 5.615,2.302 0.458,0.198 10 false IMI 4.552,2.125 5.01,2.323 0.458,0.198 10 false IMO 1.302,2.042 1.76,2.24 0.458,0.198 10 false E1 1.479,2.021 1.854,2.26 0.375,0.24 12 false *B 4.802,2.104 5.177,2.344 0.375,0.24 12 false *B 5.344,2.094 5.719,2.333 0.375,0.24 12 false *B 5.885,2.104 6.344,2.302 0.458,0.198 10 false IMO 6.458,2.104 6.917,2.302 0.458,0.198 10 false IMI 6.146,2.104 6.521,2.344 0.375,0.24 12 false *A 6.646,2.104 7.021,2.344 0.375,0.24 12 false *A 2.729,2.052 3.188,2.25 0.458,0.198 10 false E1 2.896,2.052 3.271,2.292 0.375,0.24 12 false *A
*A for 1AR-FE *B for 2GR-FKS
*a Component with harness connected
(ECM)
*b Approximately 160 ms
*c Approximately 270 ms *d Approximately 40 ms
*e Approximately 60 ms *f Waveform (IMO)
*g Waveform (IMI) *h Waveform A
*i Waveform B *j Waveform C
*k Waveform A (detail) - -


NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
A43-45 (IMO) - C1-53 (E1)*2 Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform (IMO))
A43-29 (IMO) - C1-16 (E1)*1 Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform (IMO))
A43-59 (IMI) - C1-53 (E1)*2 Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform (IMI))
A43-28 (IMI) - C1-16 (E1)*1 Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform (IMI))


*1: for 1AR-FE

*2: for 2GR-FKS


Result:
Result Proceed to
Normal waveform A
Waveform A not output, or has abnormal wavelength or shape (w/ Rear Seat Heater) B
Waveform A not output, or has abnormal wavelength or shape (w/o Rear Seat Heater) C
Waveform B not output, or has abnormal wavelength or shape D
Waveform C not output, or has abnormal wavelength or shape (w/ Rear Seat Heater) E
Waveform C not output, or has abnormal wavelength or shape (w/o Rear Seat Heater) F




A

4.REGISTER ECU COMMUNICATION ID

B

6.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

C

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

D

E

8.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

F

12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
4.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER ENGINE STARTS
5.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

8.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
6.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the F67 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F67-3 (EFII) - A43-45 (IMO)*2 Always Below 1 Ω
F67-3 (EFII) - A43-29 (IMO)*1 Always Below 1 Ω
F67-4 (EFIO) - A43-59 (IMI)*2 Always Below 1 Ω
F67-4 (EFIO) - A43-28 (IMI)*1 Always Below 1 Ω
F67-3 (EFII) or A43-45 (IMO) - Body ground*2 Always 10 kΩ or higher
F67-3 (EFII) or A43-29 (IMO) - Body ground*1 Always 10 kΩ or higher
F67-4 (EFIO) or A43-59 (IMI) - Body ground*2 Always 10 kΩ or higher
F67-4 (EFIO) or A43-28 (IMI) - Body ground*1 Always 10 kΩ or higher


*1: for 1AR-FE

*2: for 2GR-FKS



Result:
Proceed to
OK
NG



OK

8.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the F10 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-7 (EFII) - A43-45 (IMO) Always Below 1 Ω
F10-6 (EFIO) - A43-59 (IMI) Always Below 1 Ω
F10-7 (EFII) or A43-45 (IMO) - Body ground Always 10 kΩ or higher
F10-6 (EFIO) or A43-59 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.REGISTER RECOGNITION CODE
9.REGISTER RECOGNITION CODE
a.

Reregister the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG

12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.REGISTER RECOGNITION CODE