Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019700 AUDIO / VIDEO _0096790 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio and display receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based on vehicle speed signals sent from the combination meter assembly.


for "Bluetooth":

Vehicle speed signals are sent from the combination meter assembly and used to cancel "Bluetooth" function operation.

The radio and display receiver assembly recognizes that the vehicle is being driven and makes it impossible to connect or register a "Bluetooth" device while driving.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

for 1AR-FE



E361313E01
1.156,0.26 1.615,0.458 0.458,0.198 10 false SP1 1.521,0.26 1.979,0.458 0.458,0.198 10 false 14 0.073,0.813 0.531,1.01 0.458,0.198 10 false A86 0.073,0.958 3.01,1.177 2.938,0.219 10 false Brake Actuator Assembly (Skid Control ECU) 5.521,0.25 7.156,0.51 1.635,0.26 10 false 6 5.521,1.688 7.156,1.948 1.635,0.26 10 false 5 5.688,0.354 7.156,0.604 1.469,0.25 10 false SI 5.688,1.792 7.156,2.042 1.469,0.25 10 false +S 5.229,2.188 7.156,2.438 1.927,0.25 10 false Combination Meter Assembly 5.24,2.021 7.156,2.365 1.917,0.344 10 false F126 5.688,2.875 7.156,3.125 1.469,0.25 10 false SPD 5.688,4.031 7.156,4.281 1.469,0.25 10 false SPD 5.458,2.875 7.156,3.177 1.698,0.302 10 false 17 5.427,4.031 7.156,4.344 1.729,0.313 10 false 17 4.677,3.385 7.156,3.667 2.479,0.281 10 false Radio and Display Receiver Assembly*4 4.677,3.219 7.156,3.656 2.479,0.438 10 false F71 5.104,4.531 7.156,4.927 2.052,0.396 10 false Navigation Receiver Assembly*5 5.115,4.375 7.156,4.917 2.042,0.542 10 false F116 5.333,5.302 7.156,5.906 1.823,0.604 10 false A70 5.333,6.531 7.156,7.135 1.823,0.604 10 false A71 5.365,5.094 7.156,5.448 1.792,0.354 10 false 10 5.417,6.323 7.156,6.677 1.74,0.354 10 false 8 5.365,6.938 7.156,7.427 1.792,0.49 10 false No. 1 Junction Connector 4.115,1.802 4.51,2.063 0.396,0.26 10 false F95 4.115,5.313 4.688,5.552 0.573,0.24 10 false F95 4.115,2.969 4.479,3.24 0.365,0.271 10 false F94 2.771,5.313 3.198,5.615 0.427,0.302 10 false F95 2.771,4.135 3.26,4.479 0.49,0.344 10 false F94 2.771,2.969 3.313,3.26 0.542,0.292 10 false F94 2.771,1.792 3.323,2.094 0.552,0.302 10 false F94 4.156,1.594 4.531,1.906 0.375,0.313 10 false 22 4.167,2.76 4.594,3.021 0.427,0.26 10 false 12 4.146,5.104 7.156,5.542 3.01,0.438 10 false 21 2.802,5.104 3.198,5.344 0.396,0.24 10 false 20 2.802,3.948 3.24,4.281 0.438,0.333 10 false 14 2.802,2.771 3.24,3.115 0.438,0.344 10 false 13 2.802,1.604 3.281,2.01 0.479,0.406 10 false 15 3.125,5.729 4.052,6.156 0.927,0.427 10 false No. 4 Junction Connector 1.156,1.698 2.625,1.948 1.469,0.25 10 false SPD 1.156,2.865 2.625,3.115 1.469,0.25 10 false SPD 1.063,4.042 2.531,4.292 1.469,0.25 10 false SPDP 1.146,5.208 2.615,5.458 1.469,0.25 10 false SPD 1.156,6.417 2.625,6.667 1.469,0.25 10 false SPD 1.531,1.698 1.906,2.01 0.375,0.313 10 false 24 1.531,2.865 1.906,3.177 0.375,0.313 10 false 11 1.531,4.042 1.906,4.354 0.375,0.313 10 false 10 1.531,5.198 1.906,5.51 0.375,0.313 10 false 5 1.542,6.417 1.917,6.729 0.375,0.313 10 false 57 0.073,2.031 0.531,2.229 0.458,0.198 10 false F79 0.073,2.156 3.01,2.375 2.938,0.219 10 false Windshield Wiper Relay Assembly*1 0.063,3.333 3,3.552 2.938,0.219 10 false Stereo Component Amplifier Assembly*2 0.073,3.188 0.531,3.385 0.458,0.198 10 false F76 0.26,4.354 0.719,4.552 0.458,0.198 10 false F140 0.26,4.51 3.198,4.729 2.938,0.219 10 false Telematics Transceiver*6 0.063,5.479 0.521,5.677 0.458,0.198 10 false F13 0.052,5.646 2.99,5.865 2.938,0.219 10 false Certification ECU (Smart Key ECU Assembly)*3 4.667,8.25 7.156,8.5 2.49,0.25 10 false *6: w/ Manual (SOS) Switch 0.563,6.844 1.021,7.042 0.458,0.198 10 false A43 1.01,6.844 1.469,7.042 0.458,0.198 10 false ECM 0.5,7.75 4.167,7.948 3.667,0.198 10 false *1: w/ Auto Wiper System 2.5,7.75 6.167,7.948 3.667,0.198 10 false *2: for 12 Speakers 4.667,7.75 7.156,8.083 2.49,0.333 10 false *3: w/ Smart Entry and Start System 2.5,8.25 6.167,8.448 3.667,0.198 10 false *5: for Navigation Receiver Type 0.5,8.25 4.167,8.448 3.667,0.198 10 false *4: for Radio and Display Type

for 2GR-FKS


E361313E02
1.156,0.26 1.615,0.458 0.458,0.198 10 false SP1 1.521,0.26 1.979,0.458 0.458,0.198 10 false 14 0.073,0.813 0.531,1.01 0.458,0.198 10 false A86 0.073,0.958 3.01,1.177 2.938,0.219 10 false Brake Actuator Assembly (Skid Control ECU) 5.521,0.25 7.156,0.51 1.635,0.26 10 false 6 5.521,1.688 7.156,1.948 1.635,0.26 10 false 5 5.688,0.354 7.156,0.604 1.469,0.25 10 false SI 5.688,1.792 7.156,2.042 1.469,0.25 10 false +S 5.229,2.188 7.156,2.438 1.927,0.25 10 false Combination Meter Assembly 5.24,2.021 7.156,2.365 1.917,0.344 10 false F126 5.688,2.875 7.156,3.125 1.469,0.25 10 false SPD 5.688,4.031 7.156,4.281 1.469,0.25 10 false SPD 5.458,2.875 7.156,3.177 1.698,0.302 10 false 17 5.427,4.031 7.156,4.344 1.729,0.313 10 false 17 4.677,3.385 7.156,3.667 2.479,0.281 10 false Radio and Display Receiver Assembly*4 4.677,3.219 7.156,3.656 2.479,0.438 10 false F71 5.104,4.531 7.156,4.927 2.052,0.396 10 false Navigation Receiver Assembly*5 5.115,4.375 7.156,4.917 2.042,0.542 10 false F116 5.333,5.302 7.156,5.906 1.823,0.604 10 false A70 5.333,6.531 7.156,7.135 1.823,0.604 10 false A71 5.365,5.094 7.156,5.448 1.792,0.354 10 false 10 5.417,6.323 7.156,6.677 1.74,0.354 10 false 8 5.365,6.938 7.156,7.427 1.792,0.49 10 false No. 1 Junction Connector 4.115,1.802 4.51,2.063 0.396,0.26 10 false F95 4.115,5.313 4.688,5.552 0.573,0.24 10 false F95 4.115,2.969 4.479,3.24 0.365,0.271 10 false F94 2.771,5.313 3.198,5.615 0.427,0.302 10 false F95 2.771,4.135 3.26,4.479 0.49,0.344 10 false F94 2.771,2.969 3.313,3.26 0.542,0.292 10 false F94 2.771,1.792 3.323,2.094 0.552,0.302 10 false F94 4.156,1.594 4.531,1.906 0.375,0.313 10 false 22 4.167,2.76 4.594,3.021 0.427,0.26 10 false 12 4.146,5.104 7.156,5.542 3.01,0.438 10 false 21 2.802,5.104 3.198,5.344 0.396,0.24 10 false 20 2.802,3.948 3.24,4.281 0.438,0.333 10 false 14 2.802,2.771 3.24,3.115 0.438,0.344 10 false 13 2.802,1.604 3.281,2.01 0.479,0.406 10 false 15 3.125,5.729 4.052,6.156 0.927,0.427 10 false No. 4 Junction Connector 1.156,1.698 2.625,1.948 1.469,0.25 10 false SPD 1.156,2.865 2.625,3.115 1.469,0.25 10 false SPD 1.063,4.042 2.531,4.292 1.469,0.25 10 false SPDP 1.146,5.208 2.615,5.458 1.469,0.25 10 false SPD 1.156,6.417 2.625,6.667 1.469,0.25 10 false SPD 1.531,1.698 1.906,2.01 0.375,0.313 10 false 24 1.531,2.865 1.906,3.177 0.375,0.313 10 false 11 1.531,4.042 1.906,4.354 0.375,0.313 10 false 10 1.531,5.198 1.906,5.51 0.375,0.313 10 false 5 1.542,6.417 1.917,6.729 0.375,0.313 10 false 39 0.073,2.031 0.531,2.229 0.458,0.198 10 false F79 0.073,2.156 3.01,2.375 2.938,0.219 10 false Windshield Wiper Relay Assembly*1 0.063,3.333 3,3.552 2.938,0.219 10 false Stereo Component Amplifier Assembly*2 0.073,3.188 0.531,3.385 0.458,0.198 10 false F76 0.26,4.354 0.719,4.552 0.458,0.198 10 false F140 0.26,4.51 3.198,4.729 2.938,0.219 10 false Telematics Transceiver*6 0.063,5.479 0.521,5.677 0.458,0.198 10 false F13 0.052,5.646 2.99,5.865 2.938,0.219 10 false Certification ECU (Smart Key ECU Assembly)*3 4.667,8.25 7.156,8.5 2.49,0.25 10 false *6: w/ Manual (SOS) Switch 0.563,6.844 1.021,7.042 0.458,0.198 10 false A43 1.01,6.844 1.469,7.042 0.458,0.198 10 false ECM 0.5,7.75 4.167,7.948 3.667,0.198 10 false *1: w/ Auto Wiper System 2.5,7.75 6.167,7.948 3.667,0.198 10 false *2: for 12 Speakers 4.667,7.75 7.156,8.083 2.49,0.333 10 false *3: w/ Smart Entry and Start System 2.5,8.25 6.167,8.448 3.667,0.198 10 false *5: for Navigation Receiver Type 0.5,8.25 4.167,8.448 3.667,0.198 10 false *4: for Radio and Display Type


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E227878

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal Check Mode in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

While driving the vehicle, compare the value displayed for "SPEED" to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "Vehicle Signal Check Mode" screen is almost the same as the actual vehicle speed measured using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.

Check the output waveform.

E265790C34
1.75,0.333 2.167,0.583 0.417,0.25 2.438,1.188 2.708,0.594 false 0.208,0.156 0.521,0.354 0.313,0.198 10 false *a 2.75,0.458 3.063,0.656 0.313,0.198 10 false +S 4.656,1.635 4.969,1.833 0.313,0.198 10 false A 6.021,1.458 6.417,1.688 0.396,0.229 10 false GND 1.802,0.375 2.24,0.583 0.438,0.208 10 false F126
*1 Component with harness connected
(Combination Meter Assembly)
- -


i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal F126-5 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F126-5 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.
E277606C15
1.552,0.219 1.969,0.51 0.417,0.292 2.667,2.052 2.406,1.469 false 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 1.646,0.292 1.958,0.49 0.313,0.198 10 false F71 2.625,2.094 3.073,2.396 0.448,0.302 10 false SPD 2.979,3.729 3.427,4.031 0.448,0.302 10 false GND 1.26,4.01 1.708,4.313 0.448,0.302 10 false A
*a Component with harness connected
(Radio and Display Receiver Assembly)


Check the input waveform.

i.

Remove the radio and display receiver assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal F71-17 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F71-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 JUNCTION CONNECTOR)
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Disconnect the F94 No. 4 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-17 (SPD) - F94-12 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 JUNCTION CONNECTOR)
a.

Disconnect the F126 combination meter assembly connector.


b.

Disconnect the F95 No. 4 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F126-5 (+S) - F95-22 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR