Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _019708 METER / GAUGE / DISPLAY _0104486 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the brake actuator assembly (skid control ECU) which uses this information to create the vehicle speed signal*. The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the brake actuator assembly (skid control ECU). The pulse signal is created by switching the transistor in the brake actuator assembly (skid control ECU) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the brake actuator assembly (skid control ECU). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*: This vehicle speed signal is created by the brake actuator assembly (skid control ECU). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

for 1AR-FE


E361313E01
1.156,0.26 1.615,0.458 0.458,0.198 10 false SP1 1.521,0.26 1.979,0.458 0.458,0.198 10 false 14 0.073,0.813 0.531,1.01 0.458,0.198 10 false A86 0.073,0.958 3.01,1.177 2.938,0.219 10 false Brake Actuator Assembly (Skid Control ECU) 5.521,0.25 7.156,0.51 1.635,0.26 10 false 6 5.521,1.688 7.156,1.948 1.635,0.26 10 false 5 5.688,0.354 7.156,0.604 1.469,0.25 10 false SI 5.688,1.792 7.156,2.042 1.469,0.25 10 false +S 5.229,2.188 7.156,2.438 1.927,0.25 10 false Combination Meter Assembly 5.24,2.021 7.156,2.365 1.917,0.344 10 false F126 5.688,2.875 7.156,3.125 1.469,0.25 10 false SPD 5.688,4.031 7.156,4.281 1.469,0.25 10 false SPD 5.458,2.875 7.156,3.177 1.698,0.302 10 false 17 5.427,4.031 7.156,4.344 1.729,0.313 10 false 17 4.677,3.385 7.156,3.667 2.479,0.281 10 false Radio and Display Receiver Assembly*4 4.677,3.219 7.156,3.656 2.479,0.438 10 false F71 5.104,4.531 7.156,4.927 2.052,0.396 10 false Navigation Receiver Assembly*5 5.115,4.375 7.156,4.917 2.042,0.542 10 false F116 5.333,5.302 7.156,5.906 1.823,0.604 10 false A70 5.333,6.531 7.156,7.135 1.823,0.604 10 false A71 5.365,5.094 7.156,5.448 1.792,0.354 10 false 10 5.417,6.323 7.156,6.677 1.74,0.354 10 false 8 5.365,6.938 7.156,7.427 1.792,0.49 10 false No. 1 Junction Connector 4.115,1.802 4.51,2.063 0.396,0.26 10 false F95 4.115,5.313 4.688,5.552 0.573,0.24 10 false F95 4.115,2.969 4.479,3.24 0.365,0.271 10 false F94 2.771,5.313 3.198,5.615 0.427,0.302 10 false F95 2.771,4.135 3.26,4.479 0.49,0.344 10 false F94 2.771,2.969 3.313,3.26 0.542,0.292 10 false F94 2.771,1.792 3.323,2.094 0.552,0.302 10 false F94 4.156,1.594 4.531,1.906 0.375,0.313 10 false 22 4.167,2.76 4.594,3.021 0.427,0.26 10 false 12 4.146,5.104 7.156,5.542 3.01,0.438 10 false 21 2.802,5.104 3.198,5.344 0.396,0.24 10 false 20 2.802,3.948 3.24,4.281 0.438,0.333 10 false 14 2.802,2.771 3.24,3.115 0.438,0.344 10 false 13 2.802,1.604 3.281,2.01 0.479,0.406 10 false 15 3.125,5.729 4.052,6.156 0.927,0.427 10 false No. 4 Junction Connector 1.156,1.698 2.625,1.948 1.469,0.25 10 false SPD 1.156,2.865 2.625,3.115 1.469,0.25 10 false SPD 1.063,4.042 2.531,4.292 1.469,0.25 10 false SPDP 1.146,5.208 2.615,5.458 1.469,0.25 10 false SPD 1.156,6.417 2.625,6.667 1.469,0.25 10 false SPD 1.531,1.698 1.906,2.01 0.375,0.313 10 false 24 1.531,2.865 1.906,3.177 0.375,0.313 10 false 11 1.531,4.042 1.906,4.354 0.375,0.313 10 false 10 1.531,5.198 1.906,5.51 0.375,0.313 10 false 5 1.542,6.417 1.917,6.729 0.375,0.313 10 false 57 0.073,2.031 0.531,2.229 0.458,0.198 10 false F79 0.073,2.156 3.01,2.375 2.938,0.219 10 false Windshield Wiper Relay Assembly*1 0.063,3.333 3,3.552 2.938,0.219 10 false Stereo Component Amplifier Assembly*2 0.073,3.188 0.531,3.385 0.458,0.198 10 false F76 0.26,4.354 0.719,4.552 0.458,0.198 10 false F140 0.26,4.51 3.198,4.729 2.938,0.219 10 false Telematics Transceiver*6 0.063,5.479 0.521,5.677 0.458,0.198 10 false F13 0.052,5.646 2.99,5.865 2.938,0.219 10 false Certification ECU (Smart Key ECU Assembly)*3 4.667,8.25 7.156,8.5 2.49,0.25 10 false *6: w/ Manual (SOS) Switch 0.563,6.844 1.021,7.042 0.458,0.198 10 false A43 1.01,6.844 1.469,7.042 0.458,0.198 10 false ECM 0.5,7.75 4.167,7.948 3.667,0.198 10 false *1: w/ Auto Wiper System 2.5,7.75 6.167,7.948 3.667,0.198 10 false *2: for 12 Speakers 4.667,7.75 7.156,8.083 2.49,0.333 10 false *3: w/ Smart Entry and Start System 2.5,8.25 6.167,8.448 3.667,0.198 10 false *5: for Navigation Receiver Type 0.5,8.25 4.167,8.448 3.667,0.198 10 false *4: for Radio and Display Type


for 2GR-FKS


E361313E02
1.156,0.26 1.615,0.458 0.458,0.198 10 false SP1 1.521,0.26 1.979,0.458 0.458,0.198 10 false 14 0.073,0.813 0.531,1.01 0.458,0.198 10 false A86 0.073,0.958 3.01,1.177 2.938,0.219 10 false Brake Actuator Assembly (Skid Control ECU) 5.521,0.25 7.156,0.51 1.635,0.26 10 false 6 5.521,1.688 7.156,1.948 1.635,0.26 10 false 5 5.688,0.354 7.156,0.604 1.469,0.25 10 false SI 5.688,1.792 7.156,2.042 1.469,0.25 10 false +S 5.229,2.188 7.156,2.438 1.927,0.25 10 false Combination Meter Assembly 5.24,2.021 7.156,2.365 1.917,0.344 10 false F126 5.688,2.875 7.156,3.125 1.469,0.25 10 false SPD 5.688,4.031 7.156,4.281 1.469,0.25 10 false SPD 5.458,2.875 7.156,3.177 1.698,0.302 10 false 17 5.427,4.031 7.156,4.344 1.729,0.313 10 false 17 4.677,3.385 7.156,3.667 2.479,0.281 10 false Radio and Display Receiver Assembly*4 4.677,3.219 7.156,3.656 2.479,0.438 10 false F71 5.104,4.531 7.156,4.927 2.052,0.396 10 false Navigation Receiver Assembly*5 5.115,4.375 7.156,4.917 2.042,0.542 10 false F116 5.333,5.302 7.156,5.906 1.823,0.604 10 false A70 5.333,6.531 7.156,7.135 1.823,0.604 10 false A71 5.365,5.094 7.156,5.448 1.792,0.354 10 false 10 5.417,6.323 7.156,6.677 1.74,0.354 10 false 8 5.365,6.938 7.156,7.427 1.792,0.49 10 false No. 1 Junction Connector 4.115,1.802 4.51,2.063 0.396,0.26 10 false F95 4.115,5.313 4.688,5.552 0.573,0.24 10 false F95 4.115,2.969 4.479,3.24 0.365,0.271 10 false F94 2.771,5.313 3.198,5.615 0.427,0.302 10 false F95 2.771,4.135 3.26,4.479 0.49,0.344 10 false F94 2.771,2.969 3.313,3.26 0.542,0.292 10 false F94 2.771,1.792 3.323,2.094 0.552,0.302 10 false F94 4.156,1.594 4.531,1.906 0.375,0.313 10 false 22 4.167,2.76 4.594,3.021 0.427,0.26 10 false 12 4.146,5.104 7.156,5.542 3.01,0.438 10 false 21 2.802,5.104 3.198,5.344 0.396,0.24 10 false 20 2.802,3.948 3.24,4.281 0.438,0.333 10 false 14 2.802,2.771 3.24,3.115 0.438,0.344 10 false 13 2.802,1.604 3.281,2.01 0.479,0.406 10 false 15 3.125,5.729 4.052,6.156 0.927,0.427 10 false No. 4 Junction Connector 1.156,1.698 2.625,1.948 1.469,0.25 10 false SPD 1.156,2.865 2.625,3.115 1.469,0.25 10 false SPD 1.063,4.042 2.531,4.292 1.469,0.25 10 false SPDP 1.146,5.208 2.615,5.458 1.469,0.25 10 false SPD 1.156,6.417 2.625,6.667 1.469,0.25 10 false SPD 1.531,1.698 1.906,2.01 0.375,0.313 10 false 24 1.531,2.865 1.906,3.177 0.375,0.313 10 false 11 1.531,4.042 1.906,4.354 0.375,0.313 10 false 10 1.531,5.198 1.906,5.51 0.375,0.313 10 false 5 1.542,6.417 1.917,6.729 0.375,0.313 10 false 39 0.073,2.031 0.531,2.229 0.458,0.198 10 false F79 0.073,2.156 3.01,2.375 2.938,0.219 10 false Windshield Wiper Relay Assembly*1 0.063,3.333 3,3.552 2.938,0.219 10 false Stereo Component Amplifier Assembly*2 0.073,3.188 0.531,3.385 0.458,0.198 10 false F76 0.26,4.354 0.719,4.552 0.458,0.198 10 false F140 0.26,4.51 3.198,4.729 2.938,0.219 10 false Telematics Transceiver*6 0.063,5.479 0.521,5.677 0.458,0.198 10 false F13 0.052,5.646 2.99,5.865 2.938,0.219 10 false Certification ECU (Smart Key ECU Assembly)*3 4.667,8.25 7.156,8.5 2.49,0.25 10 false *6: w/ Manual (SOS) Switch 0.563,6.844 1.021,7.042 0.458,0.198 10 false A43 1.01,6.844 1.469,7.042 0.458,0.198 10 false ECM 0.5,7.75 4.167,7.948 3.667,0.198 10 false *1: w/ Auto Wiper System 2.5,7.75 6.167,7.948 3.667,0.198 10 false *2: for 12 Speakers 4.667,7.75 7.156,8.083 2.49,0.333 10 false *3: w/ Smart Entry and Start System 2.5,8.25 6.167,8.448 3.667,0.198 10 false *5: for Navigation Receiver Type 0.5,8.25 4.167,8.448 3.667,0.198 10 false *4: for Radio and Display Type


CAUTION / NOTICE / HINT

NOTICE:

Before replacing the ECM or Certification ECU (Smart key ECU assembly), refer to Service Bulletin.*

*: w/ Smart Entry and Start System



PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
E254928C22
0.708,1.177 1.094,1.448 0.385,0.271 0.677,2.948 1.083,2.385 true 0.344,0.365 0.656,0.563 0.313,0.198 10 false *a 0.76,1.229 1.219,1.427 0.458,0.198 10 false F126 0.573,2.969 0.917,3.208 0.344,0.24 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


a.

Disconnect the F126 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F126-5 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
C364228C32
1.479,0.104 1.906,0.375 0.427,0.271 0.542,1.833 0.99,1.031 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false A86 0.385,1.875 0.844,2.073 0.458,0.198 10 false SP1 0.219,0.167 0.677,0.365 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Brake Actuator Assembly (Skid Control ECU))


a.

Connect the F126 combination meter assembly connector.


b.

Disconnect the A86 brake actuator assembly (skid control ECU) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-14 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) - COMBINATION METER ASSEMBLY)
3.INSPECT BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)
E262405C38
1.521,0.396 1.896,0.646 0.375,0.25 2.281,1.271 2.552,0.698 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 1.563,0.438 2.115,0.75 0.552,0.313 10 false F126 2.51,0.521 3.063,0.833 0.552,0.313 10 false +S 2.948,3.698 3.396,4.021 0.448,0.323 10 false GND 1.292,3.99 1.604,4.198 0.313,0.208 10 false A
*a Component with harness connected
(Combination Meter Assembly)


a.

Check the input waveform.

i.

Connect the A86 brake actuator assembly (skid control ECU) connector.


ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal F126-6 (SI) and body ground.


iv.

Turn the ignition switch to ON.


v.

Turn a wheel slowly.


vi.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Ignition switch ON, wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) - COMBINATION METER ASSEMBLY)
a.

Disconnect the F126 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-14 (SP1) - F126-6 (SI) Always Below 1 Ω
A86-14 (SP1) or F126-6 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the F95 No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-22 - F126-5 (+S) Always Below 1 Ω
F95-22 - F126-5 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR)
a.

Inspect for a short in the wire harness and connectors connected to the No. 4 junction connector shown in the wiring diagram.

HINT:

If voltage is not present, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.



b.

Disconnect the F94 No. 4 junction connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F94-12 - Body ground Ignition switch ON 4.5 to 14 V
F94-13 - Body ground*1 Ignition switch ON 4.5 to 14 V
F94-15 - Body ground*2 Ignition switch ON 4.5 to 14 V
F95-20 - Body ground*3 Ignition switch ON 4.5 to 14 V
F95-21 - Body ground Ignition switch ON 4.5 to 14 V
F94-14 - Body ground*4 Ignition switch ON 4.5 to 14 V


*1: for 12 Speakers

*2: w/ Auto Wiper System

*3: w/ Smart Entry and Start System

*4: w/ Manual (SOS) Switch



Result:
Result Proceed to
Voltage is present in all of the circuits A
Voltage is not present in one circuit B



A

REPLACE NO. 4 JUNCTION CONNECTOR

B

7.SYSTEM CHECK
7.SYSTEM CHECK
a.

Select the circuit for which voltage was not present in step 6.


Result:
Result System that uses the circuit Proceed to
F94-12 - Body ground Audio and visual system*1 or Navigation system*2 A
F94-13 - Body ground Navigation system*3 B
F94-15 - Body ground Auto wiper system*4 C
F95-20 - Body ground Smart entry and start system*5 D
F95-21 - Body ground SFI system or Automatic transaxle system*6 E
F94-14 - Body ground Telematics system*7 F


*1: for Radio and Display Type

*2: for Navigation Receiver Type

*3: for 12 Speakers

*4: w/ Auto Wiper System

*5: w/ Smart Entry and Start System

*6: for 2GR-FKS

*7: w/ Manual (SOS) Switch



A

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY OR NAVIGATION RECEIVER ASSEMBLY - BODY GROUND)

B

9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)

C

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)

D

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)

E

12.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

F

15.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BODY GROUND)
8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY OR NAVIGATION RECEIVER ASSEMBLY - BODY GROUND)
a.

Disconnect the F71 radio and display receiver assembly*1 or F116 navigation receiver assembly*2 connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-17 (SPD) - Body ground*1 Always 10 kΩ or higher
F116-17 (SPD) - Body ground*2 Always 10 kΩ or higher


*1: for Radio and Display Type

*2: for Navigation Receiver Type



Result:
Result Proceed to
OK (for Radio and Display Type) A
OK (for Navigation Receiver Type) B
NG C



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)
a.

Disconnect the F76 stereo component amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-11 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - BODY GROUND)
a.

Disconnect the F79 windshield wiper relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F79-24 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)
a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-5 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.

Disconnect the F95 No. 4 junction connector.


b.

Disconnect the A70 No. 1 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-21 - A70-10 Always Below 1 Ω
F95-21 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (NO. 1 JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (NO. 1 JUNCTION CONNECTOR)
a.

Inspect for a short in the wire harness and connectors connected to the No. 1 junction connector shown in the wiring diagram.

HINT:

If voltage is not present, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.



b.

Disconnect the A71 No. 1 junction connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A71-8 - Body ground Ignition switch ON 4.5 to 14 V



Result:
Result Proceed to
Voltage is not present in one circuit A
Voltage is present in all of the circuits B



A

14.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

B

REPLACE NO. 1 JUNCTION CONNECTOR

14.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the A43 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-57 (SPD) - Body ground*1 Always 10 kΩ or higher
A43-39 (SPD) - Body ground*2 Always 10 kΩ or higher


*1: for 1AR-FE

*2: for 2GR-FKS



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BODY GROUND)
a.

Disconnect the F140 telematics transceiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F140-10 (SPDP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR