Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › HEATED OXYGEN SENSOR(for Bank 1) › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0303263 HEATED OXYGEN SENSOR(for Bank 1) A

2GR-FKS ENGINE CONTROL  HEATED OXYGEN SENSOR(for Bank 1)  INSTALLATION  


PROCEDURE

Hide 89465 1.INSTALL HEATED OXYGEN SENSOR (for AWD)

a.
A369390C01
1.875,1.656 1.479,1.656 1.479,1.656 1.115,1.26 true 1.698,0.438 1.875,0.625 0.177,0.188 10 true *a 1.896,1.583 2.26,1.781 0.365,0.198 10 false SST
*a Torque Wrench Fulcrum Length


Using SST, install the heated oxygen sensor to the front No. 3 exhaust pipe sub-assembly.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the heated oxygen sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




b.
A376731C01
1.479,1.219 1.615,1.219 1.615,1.219 1.854,0.927 true 1.323,1.146 1.635,1.344 0.313,0.198 10 false *1 1.313,0.615 1.625,0.813 0.313,0.198 10 false *a 1.99,0.167 2.302,0.365 0.313,0.198 10 false *b
*1 Wire Harness Clamp Bracket
*a Left of Vehicle
*b 180°


Install the wire harness clamp bracket to the heated oxygen sensor.

HINT:

Make sure the direction of the wire harness clamp bracket is as shown in the illustration.



Hide 17403 2.INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY (for AWD)

Hide 89465 3.INSTALL HEATED OXYGEN SENSOR (for 2WD)

a.
A395566C01
2.51,1.094 2.51,0.646 true 1.292,0.438 1.521,0.615 0.229,0.177 10 true *a 2.385,1.104 2.76,1.281 0.375,0.177 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the heated oxygen sensor to the front No. 3 exhaust pipe sub-assembly.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the heated oxygen sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




b.
A394331C01
1.958,3.083 2.177,3.083 2.177,3.083 2.458,2.854 false 1.792,3.021 2.104,3.177 0.313,0.156 10 false *1 1.667,2.635 1.979,2.792 0.313,0.156 10 false *a 2.542,2.073 2.854,2.229 0.313,0.156 10 false *b
*1 Wire Harness Clamp Bracket
*a Left of Vehicle
*b 180°


Install the wire harness clamp bracket to the heated oxygen sensor.

HINT:

Make sure the direction of the wire harness clamp bracket is as shown in the illustration.



c.

Engage the 3 wire harness clamps.


d.

Connect the heated oxygen sensor connector.


Hide 51442 5.INSTALL NO. 2 ENGINE UNDER COVER