Home › Engine / Hybrid System › 1AR-FE INTAKE / EXHAUST › EXHAUST PIPE › from 2016.11
RM3160E _51 Engine / Hybrid System _019675 1AR-FE INTAKE / EXHAUST _0104506 EXHAUST PIPE A

1AR-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum 41.5 mm (1.63 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install a new gasket to the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold converter sub-assembly (TWC: Front Catalyst).

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Install the front exhaust pipe assembly to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A310336C02
0.865,0.219 1.073,0.219 1.073,0.219 1.156,0.594 false 0.75,1.156 0.938,1.156 0.938,1.156 1.094,0.885 false 2.688,0.146 2.469,0.146 2.469,0.146 2.406,0.771 true 0.677,0.156 0.99,0.313 0.313,0.156 10 false *1 0.573,1.083 0.885,1.24 0.313,0.156 10 false *2 2.75,0.073 3.063,0.229 0.313,0.156 10 false *3 0.271,0.688 0.583,0.844 0.313,0.156 10 false *a
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly is consistent front-to-rear and left-to-right.



Hide 17420 2.INSTALL CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.

Install a new gasket to the front exhaust pipe assembly.


b.

Connect the center exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust pipe support.


c.

Install the center exhaust pipe assembly (TWC: Rear Catalyst) to the front exhaust pipe assembly with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17430 3.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum 41.5 mm (1.63 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install a new gasket to the center exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Center Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the center exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the tail exhaust pipe assembly to the 4 exhaust pipe supports.


e.

Install the tail exhaust pipe assembly to the center exhaust pipe assembly (TWC: Rear Catalyst) with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966C27
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.24,0.948 2.625,0.448 2.625,0.448 2.823,0.448 true 0.708,0.354 1.021,0.656 0.313,0.302 10 false *1 0.74,1.448 0.99,1.698 0.25,0.25 10 false *2 2.875,0.385 3.219,0.677 0.344,0.292 10 false *3 0.625,1.74 1,2.01 0.375,0.271 10 false *a
*1 Center Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Tail Exhaust Pipe Assembly
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the center exhaust pipe assembly (TWC: Rear Catalyst) and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.



Hide 51442 6.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 7.INSTALL NO. 1 ENGINE UNDER COVER

Hide 8.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

a.

Perform "Inspection After Repair" after repairing an exhaust gas leak.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION