Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2016.11
RM3160E _59 Vehicle Exterior _019719 DOOR / HATCH _0108187 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 75793 2.INSTALL FRONT DOOR UPPER OUTSIDE MOULDING PAD

Hide 3.INSTALL FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 75969 5.INSTALL FRONT DOOR REAR INNER BLACK OUT TAPE

Hide 75939 6.INSTALL FRONT DOOR UPPER INNER BLACK OUT TAPE

Hide 75754A 7.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 75756C 8.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

Hide 75720 9.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY

Hide 67838A 10.INSTALL FRONT DOOR VENT SEAL

a.
B433234N01
1.5,1.063 1.656,1.26 0.156,0.198 10 true A 1.563,1.75 1.719,1.948 0.156,0.198 10 true A 0.219,2.271 0.677,2.469 0.458,0.198 10 false A-A

Install the front door vent seal.


Hide 67856D 11.INSTALL FRONT DOOR PANEL PROTECTOR

a.
B437336N01
2.635,0.208 2.792,0.406 0.156,0.198 10 true A 2.688,1.26 2.844,1.458 0.156,0.198 10 true A 0.781,2.125 1.24,2.323 0.458,0.198 10 false A-A 1.833,0.188 1.99,0.385 0.156,0.198 10 true a

Install the front door panel protector.

HINT:

Press the area (a) shown in the illustration to confirm that the front door panel protector is securely installed to the door.



Hide 67001A 12.INSTALL FRONT DOOR PANEL CUSHION

a.
B362057

Engage the 2 claws to install 2 new front door panel cushions.


Hide 67663D 13.INSTALL DOOR FRAME GARNISH

a.
B362056

Engage the 3 claws to install the door frame garnish.


Hide 67924 14.INSTALL FRONT DOOR NO. 2 STIFFENER CUSHION

a.

Clean the front door panel.


b.
B362055C01
0,0 0,0 false
V100155

Double-sided Tape


Engage the 2 guides.


c.

Install a new front door No. 2 stiffener cushion with the 2 bolts.


Hide 67862 15.INSTALL FRONT DOOR WEATHERSTRIP

a.
B362054

Engage the 20 clips to install the front door weatherstrip.


Hide 68620 16.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door check assembly.


b.

Clean the bolt hole on the vehicle body.


c.

Clean the bolt threads of the bolt.


d.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
B362053C02
0,0 0,0 false
V100135

Bolt
V100136

Nut


Install the front door check assembly with the 2 nuts and bolt.

Torque:
Bolt : 27 N*m (275 kgf*cm, 20 ft.*lbf)
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 69312 17.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B362052N01
3.073,0.698 3.229,0.896 0.156,0.198 10 false 1 2.01,0.406 2.167,0.604 0.156,0.198 10 true 2

Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 69202A 18.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B362050C01
0.083,0.083 0.417,0.302 0.333,0.219 12 false *A 0.167,2.583 0.521,2.823 0.354,0.24 12 false *B
*A Outside
*B Inside


Engage the claw.


c.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


d.

w/ Smart Entry and Start System:

i.
B360816

Engage the 3 clamps.



Hide 69760C 19.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B360814

Install the front door inside locking cable assembly as shown in the illustration.


Hide 69720B 20.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B360812

Install the front door lock remote control cable assembly as shown in the illustration.


b.
B360810

Engage the 2 claws as shown in the illustration.


Hide 69040A 21.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing a removed front door lock with motor assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock with motor assembly.



a.

Apply MP grease to the sliding parts of the front door lock with motor assembly.


b.

When reusing the front door lock with motor assembly:

i.
B360815

Install a new door lock wiring harness seal to the front door lock with motor assembly.



c.
B360807C01
3.094,2.771 3.01,2.604 true 3.031,2.802 3.281,3.01 0.25,0.208 10 true *1
*1 Front Door Lock Open Rod


Connect the front door lock open rod to the front door lock with motor assembly.

HINT:

Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.



d.

Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Connect the connector.


Hide 69242E 22.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B360806

Engage the 2 claws to install the front door rear outside handle pad.


Hide 69241H 23.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B360805

Engage the 3 claws to install the front door front outside handle pad.


Hide 69220 24.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B360804

Insert the front end of the front door outside handle assembly into the front door outside handle frame sub-assembly.


b.

Insert the rear end of the front door outside handle assembly into the front door outside handle frame sub-assembly, then slide the front door outside handle assembly toward the front of the vehicle to install it.


c.

w/ Smart Entry and Start System:

i.
B360802

Connect the connector.


ii.

Engage the 2 claws.



Hide 69217D 25.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B360798

Engage the 2 guides and claw to install the front door outside handle cover to the lock cylinder assembly as shown in the illustration.


Hide 69217D 26.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B360800

Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B360796

Install the hole plug.


Hide 27.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B360799

Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B360795

Install the hole plug.


Hide 67404F 28.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B360792

Engage the guide.


b.

Install the front door rear lower frame sub-assembly with the bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 67402F 29.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B360794

Engage the guide.


b.

Install the front door front lower frame sub-assembly with the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


c.
B360793

Connect the wire harness with the 2 bolts.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


Hide 68151D 30.INSTALL FRONT DOOR GLASS RUN

a.
B360791

Install the front door glass run.


Hide 85720D 31.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the power window regulator motor assembly.


a.
B360790

Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

When replacing a power window regulator motor assembly, a new power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



Hide 32.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.

Temporary install the temporary bolt to the front door window regulator assembly.


c.
B360789C01
1.896,0.583 2.167,0.75 false 1.719,0.469 2.031,0.625 0.313,0.156 10 true *a 0.667,0.552 0.823,0.75 0.156,0.198 10 true 1 1.344,0.469 1.5,0.667 0.156,0.198 10 true 2 2.01,1.417 2.167,1.615 0.156,0.198 10 true 3 2.635,0.177 2.792,0.375 0.156,0.198 10 true 4 2.615,1.396 2.771,1.594 0.156,0.198 10 true 5 2.063,0.167 2.219,0.365 0.156,0.198 10 true 6
*a Temporary Bolt


Temporarily install the front door window regulator assembly with the 5 bolts.


d.

Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 68102 33.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

Connect the cable to the negative (-) battery terminal.


b.

for Driver Side:

i.

Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


ii.

Disconnect the power window regulator master switch assembly.



c.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


ii.

Disconnect the power window regulator switch assembly.



d.

Disconnect the cable from the negative (-) battery terminal.


e.

Disconnect the multiplex network master switch assembly.


f.
B360787N01
1.604,0.229 1.76,0.427 0.156,0.198 10 false 1 0.323,0.302 0.479,0.5 0.156,0.198 10 true 2

Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.


g.
B360785

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.
B360784

Install the grommet.


Hide 67832 34.INSTALL FRONT DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the front door panel.


b.
B360783C01
0.458,0.323 0.625,0.406 false 2.563,0.51 2.708,0.385 false 1.365,3.229 1.5,3.229 false 0.25,0.208 0.563,0.365 0.313,0.156 10 true *a 2.74,0.271 2.958,0.438 0.219,0.167 10 true *a 1.552,3.135 1.771,3.302 0.219,0.167 10 true *a
*a Reference Point


Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.


c.

Install the new front door service hole cover according to the reference points on the front door panel.

NOTICE:

Securely install the front door service hole cover preventing wrinkles and air bubbles.



Hide 86160 35.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 36.INSTALL OUTER REAR VIEW MIRROR WITH COVER

Hide 89430 37.INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)

Hide 84927C 38.INSTALL SEAT MEMORY SWITCH (w/ Memory)

Hide 68172A 39.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

a.
B360780

Engage the 7 claws to install the front door inner glass weatherstrip as shown in the illustration.


Hide 69206B 40.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B360778

Engage the guide and 2 claws to install the front door inside handle sub-assembly to the front door trim board sub-assembly.


Hide 67602 41.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B360777C01
2.385,0.74 1.865,0.365 true 2.563,1.5 2.75,1.104 true 1.677,0.281 1.99,0.438 0.313,0.156 10 true *1 2.458,1.531 2.771,1.688 0.313,0.156 10 true *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly


Connect the front door lock remote control cable assembly and front door inside locking cable assembly.


b.

w/ Memory:

i.

Connect the connector.



c.

w/ Illumination:

i.

Connect the connector.



d.
B360775

Engage the 10 clips to install the front door trim board sub-assembly as shown in the illustration.


e.
B360773

Install the 3 screws.


f.
B360772

Engage the claw to close the cover.


Hide 81230N 42.INSTALL COURTESY LIGHT ASSEMBLY

Hide 43.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

a.

Connect each connector.


b.
B360763

Engage the 2 guides, 2 clips and 4 claws to install the power window regulator master switch assembly with front door upper armrest base panel.


Hide 44.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

a.

Connect each connector.


b.
B360769

Engage the 2 guides, 2 clips and 4 claws to install the power window regulator switch assembly with front door upper armrest base panel.


Hide 69284C 45.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B360761

Engage the 3 claws to install the front door inside handle bezel plug.


Hide 67492A 46.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B360759

Engage the guide and 2 clips to install the front door lower frame bracket garnish.


Hide 47.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 48.INITIALIZE POWER WINDOW CONTROL SYSTEM

Hide 49.INSPECT POWER WINDOW OPERATION

Hide 86790F 51.ADJUST SIDE TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)