Home › Engine / Hybrid System › 1AR-FE FUEL › FUEL INJECTOR › from 2018.09
RM3160E _51 Engine / Hybrid System _019673 1AR-FE FUEL _0108296 FUEL INJECTOR A

1AR-FE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A196010C01
2.49,1.781 2.667,1.781 2.667,1.781 3.104,1.365 false 2.344,1.708 2.51,1.906 0.167,0.198 10 *1
*1 O-ring


Apply a light coat of gasoline or spindle oil to new O-rings, and then install one onto each fuel injector assembly.


b.

Apply a light coat of gasoline or spindle oil where the fuel delivery pipe contacts each O-ring.


c.
A314717

While turning the fuel injector assembly left and right, install it onto the fuel delivery pipe.

NOTICE:
·

Do not damage the fuel injector assembly and O-ring.

·

Do not twist the O-ring.

·

After installing each fuel injector assembly, check that it turns smoothly. If not, replace the O-ring with a new one.




Hide 23814B 2.INSTALL FUEL DELIVERY PIPE

a.
A252632C02
1.938,0.917 2.115,0.917 false 1.125,0.49 1.313,0.667 0.188,0.177 10 false *a 1.146,1.292 1.333,1.469 0.188,0.177 10 false *b 2.167,0.833 2.354,1.01 0.188,0.177 10 false *1 1.792,2.167 1.979,2.344 0.188,0.177 10 true *1 2.219,1.833 2.406,2.01 0.188,0.177 10 true *1 1.688,3.146 1.875,3.323 0.188,0.177 10 true *2 2.052,2.927 2.24,3.104 0.188,0.177 10 true *2 2.427,2.729 2.615,2.906 0.188,0.177 10 true *2 2.76,2.552 2.948,2.729 0.188,0.177 10 true *2
*1 Fuel Delivery Spacer
*2 Injector Vibration Insulator
*a Fuel Delivery Pipe Side
*b Cylinder Head Sub-assembly Side


Install 4 new injector vibration insulators to the cylinder head sub-assembly.


b.

Install the 2 fuel delivery spacers onto the cylinder head sub-assembly.

HINT:

Install the fuel delivery spacer so that the longer protrusion is on the cylinder head sub-assembly side.



c.

Install the fuel delivery pipe with the 4 fuel injector assemblies and install the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:
·

Do not drop the fuel injector assemblies when installing the fuel delivery pipe.

·

Check that the fuel injector assemblies rotate smoothly after installing the fuel delivery pipe.




Hide 82121 3.CONNECT ENGINE WIRE

a.
A252630

Engage the clamp to connect the engine wire.


b.

Install the 2 wire harness brackets to the intake manifold with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the 4 fuel injector assembly connectors, throttle body with motor assembly connector and sensor wire connector.


Hide 17650 4.INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 23901 5.CONNECT FUEL TUBE SUB-ASSEMBLY

a.
A297392C05
2.167,3.479 2.302,2.813 2.302,2.813 2.396,2.813 false 1.813,3.271 1.594,2.771 1.594,2.771 1.49,2.771 false 0.854,4.135 0.854,3.802 false 1.271,4.313 1.563,4.313 1.563,4.313 1.563,3.781 false 1.958,3.844 2.333,4.156 2.333,4.156 1.969,3.406 false 2.948,3.438 3.188,4.146 3.188,4.146 2.896,3.802 false 1.396,4.313 1.396,3.781 false 2.458,2.719 2.771,2.875 0.313,0.156 10 false *d 1.313,2.688 1.625,2.844 0.313,0.156 10 false *c 0.781,4.208 1.146,4.479 0.365,0.271 10 false *e 1.104,4.229 1.417,4.385 0.313,0.156 10 false *b 2.365,4.177 2.677,4.333 0.313,0.156 10 false *a 3.198,4.167 3.427,4.333 0.229,0.167 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe
*e Nylon Tube


Connect the fuel tube sub-assembly to the fuel pipe.

NOTICE:

Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


i.

Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.



b.

Engage the claw and install the No. 1 fuel pipe clamp.


c.

Engage the clamp to connect the fuel tube sub-assembly to the fuel hose clamp.


Hide 17705 6.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12601B 9.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 10.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION