Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER(for 2WD) › from 2018.09
RM3160E _52 Drivetrain _019687 AXLE AND DIFFERENTIAL _0109440 REAR AXLE CARRIER(for 2WD) A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 3.REMOVE REAR DISC BRAKE CALIPER ASSEMBLY

a.
C293048C01
1.458,0.813 1.958,0.813 true 1.354,1.396 1.635,1.396 true 1.271,0.708 1.448,0.906 0.177,0.198 10 true *1 1.156,1.271 1.333,1.479 0.177,0.208 10 true *2
*1 Rear Brake Tube
*2 Rear Flexible Hose
V100136

Clip


Using a union nut wrench, separate the rear flexible hose from the rear brake tube while holding the rear flexible hose with a wrench.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




b.

Remove the clip and separate the rear flexible hose.


c.
C293049

Remove the bolt and separate the rear flexible hose from the rear upper control arm assembly.


d.

Remove the 2 bolts and rear disc brake caliper assembly with rear flexible hose.


Hide 42491 4.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 42431 5.REMOVE REAR DISC

Hide 89516B 6.SEPARATE SKID CONTROL SENSOR WIRE

Hide 42450B 7.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

Hide 8.LOOSEN PARKING BRAKE ASSEMBLY

a.
C293050

Loosen the nut to separate the parking brake assembly after removing the rear trailing arm assembly.


Hide 48780E 9.REMOVE REAR TRAILING ARM ASSEMBLY

Hide 10.SEPARATE PARKING BRAKE ASSEMBLY

a.
C293051

Remove the nut and separate the parking brake assembly from the rear axle carrier sub-assembly.

NOTICE:

Use wire or an equivalent tool to keep the parking brake assembly from hanging by the parking brake cable.



Hide 42305 11.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY

a.
C199846C02
2.417,2.344 2.417,2.583 2.417,2.583 2.698,2.583 false 2.365,1.958 2.979,1.958 true 3.01,1.865 3.271,2.135 0.26,0.271 10 false *a 2.729,2.479 2.99,2.698 0.26,0.219 10 false *b 0.573,2.875 0.771,3.094 0.198,0.219 10 true A 0.781,2.865 0.938,3.083 0.156,0.219 10 true A 0.469,1.802 0.604,2 0.135,0.198 10 true D 0.875,0.75 1.01,0.948 0.135,0.198 10 true B 2.771,0.406 2.938,0.594 0.167,0.188 10 true C
*a Wooden Block
*b Jack


Support the rear No. 2 suspension arm assembly using a jack and wooden block.

CAUTION:

Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.


NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Keep supporting the rear No. 2 suspension arm assembly until the installation of the rear axle carrier sub-assembly has been completed.




b.

Remove the 2 bolts (A), and separate the rear axle carrier sub-assembly from the rear lower shock absorber bracket sub-assembly.


c.

Remove the bolt (B) and nut, and separate the rear upper control arm assembly from the rear axle carrier sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



d.

Remove the bolt (C) and nut, and separate the rear axle carrier sub-assembly from the rear No. 2 suspension arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Remove the nut (D), spacer and rear axle carrier sub-assembly from the rear No. 1 suspension arm assembly.


Hide 48759 12.REMOVE LOWER CONTROL ARM PIN

a.
C199842

Secure the rear axle carrier sub-assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using a hammer, remove the lower control arm pin from the rear axle carrier sub-assembly.