Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2020.02–2020.11
RM37A0E _51 Engine / Hybrid System _086909 A25A-FXS INTAKE / EXHAUST _0416454 EXHAUST MANIFOLD A

A25A-FXS INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 6 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold (TWC: Front Catalyst) and No. 1 exhaust manifold heat insulator.

HINT:

At this time, do not install the parts with bolts or nuts.



c.
A455279N01
1.573,0.969 1.729,1.167 0.156,0.198 10 false 1 2.469,0.688 2.625,0.885 0.156,0.198 10 true 1 1.458,0.063 1.604,0.229 0.146,0.167 10 true 2 2.771,0.031 2.917,0.219 0.146,0.188 10 true 3 1.969,0.802 2.115,0.99 0.146,0.188 10 true 4 3.104,0.281 3.24,0.458 0.135,0.177 10 true 5 1.313,0.823 1.479,1.031 0.167,0.208 10 true 6 0.885,0.177 1.021,0.344 0.135,0.167 10 true 7

Temporarily install the exhaust manifold (TWC: Front Catalyst) to the cylinder head sub-assembly with 7 new nuts.


d.

Tighten the 7 nuts in the order shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 17118 3.INSTALL MANIFOLD STAY

a.
A455278N01
3,1.323 3.156,1.521 0.156,0.198 10 true 1 0.385,1.198 0.542,1.396 0.156,0.198 10 true 2

Temporarily install the manifold stay to the exhaust manifold (TWC: Front Catalyst) and cylinder block sub-assembly with the bolt and nut.


b.

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 5 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 5.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 17410 7.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.

Install 2 new gaskets to the front exhaust pipe assembly (TWC: Rear Catalyst).


b.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


c.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) and tail exhaust pipe assembly with 2 new bolts and 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


d.
A454955C01
2.719,0.74 2.719,0.281 2.719,0.281 2.906,0.281 true 2.604,0.813 2.677,1.156 2.677,1.156 2.781,0.917 true 2.938,0.177 3.146,0.354 0.208,0.177 10 true *a 2.604,1.177 2.813,1.354 0.208,0.177 10 true *b
*a Tube
*b Wire Harness Clamp


Connect the air fuel ratio sensor (for sensor 2) connector.


e.

Engage the 2 wire harness clamps so that the tube is positioned as shown in the illustration.


Hide 55704B 8.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 9.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 10.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 11.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 12.INSTALL FRONT FENDER SPLASH SHEILD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 53808A 13.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 14.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 15.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 51420 17.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY