Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model)
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Hybrid Vehicle Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Hybrid Vehicle Control ECU Communication Stop Mode Communication stop for "Hybrid Vehicle Control" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Hybrid vehicle control ECU branch line or connector

·

Power source circuit of hybrid vehicle control ECU

·

Hybrid vehicle control ECU ground circuit

·

Hybrid vehicle control ECU



WIRING DIAGRAM

C427145E01
5.573,0.479 6.031,0.677 0.458,0.198 10 false A32 5.573,1.063 6.031,1.26 0.458,0.198 10 false A32 5.563,2.052 6.021,2.25 0.458,0.198 10 false A32 5.563,2.656 6.021,2.854 0.458,0.198 10 false A32 5.958,0.479 6.417,0.677 0.458,0.198 10 false CA1H 5.969,1.063 6.427,1.26 0.458,0.198 10 false CA1L 5.615,0.26 6.073,0.458 0.458,0.198 10 false 21 5.625,0.854 6.083,1.052 0.458,0.198 10 false 8 5.958,2.052 6.417,2.25 0.458,0.198 10 false CA3P 5.969,2.667 6.427,2.865 0.458,0.198 10 false CA3N 5.646,1.844 6.104,2.042 0.458,0.198 10 false 7 5.615,2.427 6.073,2.625 0.458,0.198 10 false 20 0.448,1.438 3.042,1.792 2.594,0.354 10 false No. 1 Global CAN Junction Connector 0.146,1.438 0.604,1.667 0.458,0.229 10 false A77 1.76,0.344 2.219,0.542 0.458,0.198 10 false 8 1.74,0.969 2.198,1.167 0.458,0.198 10 false 19 0.469,3.031 2.979,3.354 2.51,0.323 10 false No. 2 Global CAN Junction Connector 0.167,3.031 0.625,3.26 0.458,0.229 10 false H90 1.802,1.958 2.26,2.156 0.458,0.198 10 false 5 1.76,2.542 2.219,2.74 0.458,0.198 10 false 15 2.24,3.521 3.333,3.865 1.094,0.344 10 false to IGCT Relay 2.083,4.104 3.333,4.438 1.25,0.333 10 false from IGCT Relay 5.583,5.469 6.042,5.667 0.458,0.198 10 false H67 5.573,6.74 6.031,6.938 0.458,0.198 10 false A32 5.656,5.24 6.115,5.438 0.458,0.198 10 false 3 5.615,6.51 6.073,6.708 0.458,0.198 10 false 12 5.958,6.75 6.417,6.948 0.458,0.198 10 false E01 5.969,5.469 6.427,5.667 0.458,0.198 10 false E1 5.969,7.177 6.427,7.375 0.458,0.198 10 false E02 5.573,3.521 6.031,3.719 0.458,0.198 10 false A31 5.583,4.115 6.042,4.313 0.458,0.198 10 false A31 5.583,4.802 6.042,5 0.458,0.198 10 false H67 5.573,5.906 6.031,6.104 0.458,0.198 10 false A32 5.583,7.188 6.042,7.385 0.458,0.198 10 false A32 5.646,3.292 6.104,3.49 0.458,0.198 10 false 5 5.969,3.5 6.427,3.698 0.458,0.198 10 false MREL 5.969,4.094 6.427,4.292 0.458,0.198 10 false +B1 5.958,4.792 6.417,4.99 0.458,0.198 10 false +B2 5.969,5.896 6.427,6.094 0.458,0.198 10 false E12 5.615,3.885 6.073,4.083 0.458,0.198 10 false 11 4.01,3.969 4.896,4.271 0.885,0.302 10 false IGCT NO. 1 5.646,4.583 6.104,4.781 0.458,0.198 10 false 1 5.604,5.698 6.063,5.896 0.458,0.198 10 false 34 5.615,6.979 6.073,7.177 0.458,0.198 10 false 11 5.594,7.844 7,8.49 1.406,0.646 10 false Hybrid Vehicle Control ECU

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (HYBRID VEHICLE CONTROL ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A32 hybrid vehicle control ECU connector.


c.
C427146C01
1.469,0.302 1.875,0.521 0.406,0.219 1.792,1.771 1.792,0.708 1.792,0.708 1.625,0.708 true 2,1.76 2,0.698 2,0.698 2.167,0.698 true 1.896,2.063 1.896,2.938 1.896,2.938 1.729,2.938 true 2.125,2.073 2.125,2.948 2.125,2.948 2.292,2.948 true 1.552,0.333 2.01,0.531 0.458,0.198 10 false A32 1.188,0.646 1.875,0.927 0.688,0.281 10 false CA3P 2.25,0.615 2.938,0.896 0.688,0.281 10 false CA1L 2.375,2.854 3.063,3.135 0.688,0.281 10 false CA1H 1.333,2.865 2.021,3.146 0.688,0.281 10 false CA3N 0.104,0.094 0.563,0.292 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32-21(CA1H) - A32-8(CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A32-7(CA3P) - A32-20(CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK ECU POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (HYBRID VEHICLE CONTROL ECU)

2.CHECK ECU POWER SOURCE CIRCUIT

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)