1.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY
55835A
2.INSTALL CENTER HEATER TO REGISTER DUCT
3.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
55307C
4.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
55306A
5.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
6.INSTALL AIR CONDITIONER UNIT ASSEMBLY
7.CONNECT INSTRUMENT PANEL WIRE
Connect the earth wire with the bolt.
Engage each clamp.
Connect the 2 connectors.
Engage each clamp.
Install the 2 nuts.
Connect the connector holder with the bolt (B).
Connect the 5 earth wires with the 5 bolts (A).
Connect the 2 connectors.
55837C
8.INSTALL CENTER HEATER TO REGISTER SUB DUCT
55215D
9.INSTALL NO. 3 DASH PANEL INSULATOR PAD
87212G
10.INSTALL REAR NO. 3 AIR DUCT
87212H
11.INSTALL REAR NO. 4 AIR DUCT
87212
12.INSTALL REAR NO. 1 AIR DUCT
87212F
13.INSTALL REAR NO. 2 AIR DUCT
78111
14.INSTALL ACCELERATOR PEDAL
78118
15.INSTALL ACCELERATOR PEDAL PAD
88625Q
16.INSTALL COOLER (ROOM TEMP. SENSOR) THERMISTOR
89343C
17.INSTALL NO. 1 CLEARANCE WARNING BUZZER
18.INSTALL PARKING ASSIST ECU WITH BRACKET
82877
19.INSTALL ECU INTEGRATION BOX RH
45250
20.INSTALL STEERING COLUMN ASSEMBLY
87201L
21.INSTALL NO. 4 AIR DUCT SUB-ASSEMBLY
8598A
22.INSTALL DOOR CONTROL BATTERY (w/ Door Control Battery)
83108
23.INSTALL METER MIRROR SUB-ASSEMBLY (w/ Headup Display)
24.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU
25.INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)
26.INSTALL FRONT SEAT ASSEMBLY (for Power Seat)
87245B
27.CONNECT INLET HEATER WATER HOSE B
| *a | View A |
| *b | Marking (Green) |
| *c | Clip Installation Angle (60 to 120°) |
Connect the inlet heater water hose B with the marking facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the inlet heater water hose B.
87209
28.CONNECT WATER HOSE SUB-ASSEMBLY
| *a | View A |
| *b | Marking (Green) |
| *c | Clip Installation Angle (270°) |
Connect the water hose sub-assembly with the marking facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the water hose sub-assembly.
88710G
29.CONNECT NO. 2 AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
Remove the vinyl tape from the No. 2 air conditioner tube and accessory assembly.
Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the No. 2 air conditioner tube and accessory assembly.
ND-OIL 12 or equivalent
Install the 2 O-rings to the No. 2 air conditioner tube and accessory assembly.
Keep the O-rings and O-ring fitting surfaces free from dirt and foreign matter.
Connect the No. 2 air conditioner tube and accessory assembly.
Rotate the hook connector as shown in the illustration.
Insert the tube joint into the fitting hole securely and install the bolt.
55704B
30.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY
31.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH
53607B
32.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
53892C
33.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT LH
53891C
34.INSTALL FRONT FENDER SPLASH SHEILD SEAL FRONT RH
Perform the same procedure as for the LH side.
53808A
35.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH
53807A
36.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH
Perform the same procedure as for the LH side.
37.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
38.ADD ENGINE COOLANT
39.INSPECT FOR COOLANT LEAK
40.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
41.WARM UP ENGINE
42.INSPECT FOR REFRIGERANT LEAK