1.INSTALL WIRE HARNESS CLAMP BRACKET
Install the wire harness clamp bracket to the inverter with converter assembly with the 2 bolts.
Install the wire harness clamp bracket to the inverter with converter assembly with the 2 bolts.
Install the wire harness clamp bracket to the inverter with converter assembly with the 2 bolts.
Install the wire harness clamp bracket to the inverter with converter assembly with the bolt.
G9215
2.INSTALL NO. 2 INVERTER BRACKET
| *a | Bottom of Inverter with Converter Assembly |
| *b | Support |
Make sure to support the inverter with converter assembly at the positions shown in the illustration, otherwise it may be damaged.
| *a | Wooden Block |
Set the inverter with converter assembly on wooden blocks.
Temporarily install the No. 2 inverter bracket to the inverter with converter assembly with the 2 bolts.
Fully tighten the 2 bolts in the order shown in the illustration.
G9214
3.INSTALL NO. 1 INVERTER BRACKET
| *a | Wooden Block |
Temporarily install the No. 1 inverter bracket to the inverter with converter assembly with the 2 bolts.
Fully tighten the 2 bolts in the order shown in the illustration.
G9200
4.INSTALL INVERTER WITH CONVERTER ASSEMBLY
Be sure to wear insulated gloves.
Temporarily install the inverter with converter assembly with the 5 bolts and 2 nuts.
When installing the inverter with converter assembly, be careful not to damage the parts around it.
To prevent damage, do not hold the inverter with converter assembly by the connectors, brackets or cooling pipes.
To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.
| *a | Correct |
| *b | Incorrect |
Make sure that the inverter with converter assembly is positioned so that the stud bolts are in contact with the base of the U-shaped portions of the No. 1 inverter bracket.
If the bolts and nuts are not tightened appropriately, the inverter with converter assembly may make an abnormal noise.
Fully tighten the bolt (A).
Fully tighten the 3 bolts (B).
Fully tighten the bolt (C).
Fully tighten the 2 nuts (D).
5.INSTALL WIRE HARNESS CLAMP BRACKET
Install the wire harness clamp bracket to the inverter with converter assembly with the 2 bolts.
G1148
6.CONNECT MOTOR CABLE
Be sure to wear insulated gloves.
Do not allow any foreign matter or water to enter the inverter with converter assembly.
Temporarily connect the motor cable to the inverter with converter assembly with the 4 bolts.
Do not touch the waterproof seal or terminals of the connector.
Do not damage the terminals, connector housing or inverter with converter assembly during connection.
| *a | Waterproof Seal |
| *b | 10 mm Union Nut Wrench Fulcrum Length |
| *c | Torque Wrench Fulcrum Length |
Fully tighten the bolt (A).
Fully tighten the 2 bolts in the order shown in the illustration.
Using a 10 mm union nut wrench, fully tighten the bolt (B) to connect the motor cable to the inverter with converter assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
7.0 N*m (71 kgf*cm, 62 in.*lbf)
Temporarily install the 6 bolts.
To prevent the threads from being damaged, temporarily tighten the 6 bolts by hand.
Do not damage the terminals, connector housing or inverter with converter assembly during connection.
Do not touch the waterproof seal or terminals of the connector.
Using an insulated tool, fully tighten the 6 bolts.
Do not touch the waterproof seal or terminals of the connector.
Do not damage the terminals, connector housing or inverter with converter assembly during connection.
Be sure to use a torque wrench to tighten the bolts.
G9221
7.INSTALL INVERTER COVER
Be sure to wear insulated gloves.
Install the inverter cover to the inverter with converter assembly with the 2 bolts.
Visually confirm that the inverter cover waterproof seal is securely installed before installing the inverter cover.
Do not touch the waterproof seal of the inverter cover.
Make sure that the interlock is fully engaged.
Do not damage the terminals, interlock connector or inverter with converter assembly during installation.
Do not allow any foreign matter or water to enter the inverter with converter assembly.
| *1 | Inverter Cover |
| *a | Screw |
Do not remove or excessively tighten the screw of the inverter cover.
Although the inverter cover may feel loose, this is not due to a malfunction.
| *a | No Gap |
Push in the inverter cover until it contacts the inverter with converter assembly.
G9228A
8.CONNECT NO. 4 INVERTER COOLING HOSE
| *a | Alignment Mark |
| *b | Rib |
| *c | 2 to 7 mm (0.0787 to 0.276 in.) |
| *d | Up |
| *e | LH Side |
Connect the No. 4 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.
To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.
Make sure to align the alignment mark of the hose with the rib of the inverter with converter assembly.
Make sure that the clip is positioned as shown in the illustration.
G9225K
9.CONNECT NO. 1 INVERTER COOLING HOSE
| *a | Alignment Mark |
| *b | Rib |
| *c | 2 to 7 mm (0.0787 to 0.276 in.) |
| *d | Up |
| *e | LH Side |
Connect the No. 1 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.
To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.
Make sure to align the alignment mark of the hose with the rib of the inverter with converter assembly.
Make sure that the clip is positioned as shown in the illustration.
33820B
10.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Connect the transmission control cable assembly to the inverter with converter assembly with the 2 bolts.
Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.
Engage the 2 claws to install a new clip to the transmission control cable assembly.
| *1 | Transmission Control Cable Assembly |
| *2 | No. 1 Transmission Control Cable Bracket |
| *a | Claw (A) |
| *b | Claw (B) |
Using a screwdriver, engage the 4 claws and connect the transmission control cable assembly to the No. 1 transmission control cable bracket.
Make sure that the claws (A) of the clip are securely engaged in the grooves of the bracket.
Make sure that the transmission control cable assembly is securely installed inside of the claws (B) of the clip.
Connect the transmission control cable assembly to the control shaft lever with the nut.
82121
11.CONNECT ENGINE WIRE
Be sure to wear insulated gloves.
Do not allow any foreign matter or water to enter the inverter with converter assembly.
Engage the 2 clamps to connect the engine wire to the inverter with converter assembly.
Temporarily install the nut.
To prevent the threads from being damaged, temporarily tighten the nut by hand.
Fully tighten the nut.
Engage the 2 claws to close the engine wire terminal cover.
Connect the engine wire to the inverter with converter assembly with the bolt.
Connect the engine wire to the inverter with converter assembly with the bolt.
Engage the 2 clamps.
Engage the clamp.
Confirm that no foreign matter or water has entered the connector of the generator temperature sensor, resolver (transmission fluid temperature sensor) and shift lever position sensor and connect the 3 connectors.
Engage the 2 clamps (B).
Connect the engine wire to the inverter with converter assembly with the bolt.
Engage the 3 clamps (A) to connect the No. 1 fuel vapor feed hose.
Connect the inverter with converter assembly connector and move the lock lever to lock it.
Do not touch the waterproof seal or terminals of the connector.
To prevent damage due to static electricity, do not touch the terminals of the disconnected connector.
Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.
12.INSTALL WIRE HARNESS CLAMP BRACKET
Install the wire harness clamp bracket to the inverter with converter assembly with the nut.
821H2
13.CONNECT HV AIR CONDITIONING WIRE
Be sure to wear insulated gloves.
| *a | Waterproof Seal |
Engage the clamp to connect the HV air conditioning wire to the inverter with converter assembly.
Do not allow any foreign matter or water to enter the inverter with converter assembly.
Do not touch the waterproof seal or terminals of the connector.
Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.
Install the 2 bolts.
821H1
14.CONNECT FLOOR UNDER WIRE
Be sure to wear insulated gloves.
| *a | Waterproof Seal |
Install the 2 bolts to connect the HV floor under wire to the inverter with converter assembly.
Do not allow any foreign matter or water to enter the inverter with converter assembly.
Do not touch the waterproof seal or terminals of the connector.
Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.
Connect the HV floor under wire to the inverter with converter assembly with the 2 nuts.
for 4WD/AWD:
| *a | Waterproof Seal |
Connect the HV floor under wire to the inverter with converter assembly with the 2 bolts.
Make sure that the connector is fully engaged.
Do not damage the terminals, interlock connector or inverter with converter assembly when connecting the connector.
Do not touch the waterproof seal or terminals of the connector.
Do not allow any foreign matter or water to enter the inverter with converter assembly.
Although the connector may feel loose, this is not due to a malfunction.
82111
15.CONNECT ENGINE ROOM MAIN WIRE
Be sure to wear insulated gloves.
Engage the clamp to connect the engine room main wire to the inverter with converter assembly.
Install the bolt.
Connect the inverter with converter assembly connector and move the lock lever to lock it.
Do not touch the waterproof seal or terminals of the connector.
To prevent damage due to static electricity, do not touch the terminals of the disconnected connector.
Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.
89661
16.INSTALL ECM
17.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
| *a | Protrusion |
| *b | Cutout |
| *c | Hose Clamp End |
| *d | Paint Mark |
| *e | 2 mm (0.0787 in.) |
| *f | 4 mm (0.157 in.) |
| *g | End of Hose Clamp Location |
Install the air cleaner assembly with air cleaner hose to the throttle body with motor assembly.
Align the cutout of the air cleaner hose with the protrusion of the throttle body with motor assembly.
Tighten the hose clamp in the position shown in the illustration.
Make sure that the end of the hose clamp is positioned as shown in the illustration.
| *a | Up |
| *b | Front of Vehicle |
| *c | 45°(Claw of Clip Location) |
| *d | Paint Mark |
Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.
Make sure that the clip is positioned as shown in the illustration.
Engage the 2 grommets and pin to install the air cleaner assembly with air cleaner hose.
Engage the wire harness clamp.
Connect the mass air flow meter sub-assembly connector.
17750A
18.INSTALL INLET AIR CLEANER ASSEMBLY
Temporarily install the inlet air cleaner assembly with the 2 bolts.
Fully tighten the 2 bolts in the order shown in the illustration.
53295E
19.INSTALL COOL AIR INTAKE DUCT SEAL
12601B
20.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
G3834
21.INSTALL SERVICE PLUG GRIP
22.ADD COOLANT (for Inverter)
23.INSPECT FOR COOLANT LEAK (for Inverter)
24.PERFORM INITIALIZATION