Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY
RM37A0E _58 Vehicle Interior _086895 SEAT BELT _0417481 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 73200A 1.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

HINT:

Perform this procedure only when replacement of the front shoulder belt anchor adjuster assembly is necessary.


a.
B560993N01
0.875,0.229 1.031,0.427 0.156,0.198 10 true A 1.25,1.979 1.406,2.177 0.156,0.198 10 true B

Engage the guide and temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.


b.

Fully tighten the bolt (A) first, then the bolt (B) to install the front shoulder belt anchor adjuster assembly.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73220 2.INSPECT FRONT SEAT OUTER BELT ASSEMBLY

Hide 73220 3.INSTALL FRONT SEAT OUTER BELT ASSEMBLY

a.

Engage the 2 guides.


b.

Fully tighten the bolt.

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.
B560995C01
1.969,0.698 2.49,0.802 true 1.813,0.604 2.052,0.813 0.24,0.208 10 false *a 2.5,0.281 2.719,0.479 0.219,0.198 10 false *b
*a Locking Button
*b Lock


Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.



d.

Check that the ELR locks.

NOTICE:

The check should be performed with the front seat outer belt assembly installed.


i.

With the belt assembly installed, check that the belt locks when it is pulled out quickly.



e.

Connect the shoulder anchor of the front seat outer belt assembly with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62420A 4.INSTALL CENTER PILLAR GARNISH ASSEMBLY

Hide 62414A 5.INSTALL LOWER CENTER PILLAR GARNISH

Hide 73220 6.CONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.

Connect the floor anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73233 7.INSTALL LAP BELT OUTER ANCHOR COVER

a.

Engage the 3 claws to install the lap belt outer anchor cover.


Hide 8.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 67918A 9.INSTALL REAR DOOR SCUFF PLATE

Hide 72138M 10.INSTALL REAR OUTER SEAT TRACK BRACKET COVER

Hide 11.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 67914 12.INSTALL FRONT DOOR SCUFF PLATE

Hide 13.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for 2GR-FKS: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>INSTALLATION

for A25A-FXS, A25B-FXS: Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58441L 14.INSTALL BATTERY SERVICE HOLE COVER (for HV Model)