Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL SYSTEM
RM37A0E _51 Engine / Hybrid System _086852 2GR-FKS FUEL _0417506 FUEL SYSTEM G

2GR-FKS FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Check fuel pump operation.

NOTICE:

Do not start the engine.


Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 40
i.

Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank sub-assembly can be heard. If no sounds can be heard, check the relay, fuel pump, ECM and wiring connectors.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



Hide 2.CHECK FUEL PRESSURE

a.

Discharge fuel system pressure.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Measure the battery voltage.

Standard Voltage:

11 to 14 V



c.
A449867

Disengage the 2 claws to remove the No. 2 fuel pipe clamp.


d.
A449868

Remove the No. 1 fuel pipe clamp from the fuel tube connector.


e.
A454385

Disconnect the No. 2 fuel tube sub-assembly (for Direct Injection).

i.

Disconnect the No. 2 fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



f.
A454386

Disconnect the fuel tube sub-assembly (for Port Injection).

i.

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



g.
A393289C01
0.219,1.031 0.333,1.031 0.333,1.031 0.427,1.292 false 1.604,0.354 1.719,0.354 1.719,0.354 1.844,0.438 false 2.594,1.104 2.792,0.719 2.792,0.719 2.896,0.719 false 0.938,3.083 1.146,3.083 false 1.083,3.75 1.292,3.75 false 1.167,4.083 1.375,4.083 false 2.719,2.563 2.865,2.25 2.865,2.25 2.948,2.25 false 1.365,1.917 1.438,1.635 1.438,1.635 1.531,1.635 false 1.385,1.094 1.385,0.906 false 1.76,1.26 1.875,1.26 1.875,1.26 1.99,1.021 false 1.302,1.115 1.615,1.271 0.313,0.156 10 false *1 1.427,0.26 1.74,0.417 0.313,0.156 10 false *a 1.604,1.177 1.917,1.333 0.313,0.156 10 false *b 0.063,0.938 0.375,1.094 0.313,0.156 10 false *c 1.573,1.552 1.885,1.708 0.313,0.156 10 false *d 3,2.167 3.313,2.323 0.313,0.156 10 false *e 0.927,3.667 1.24,3.823 0.313,0.156 10 false *f 1.01,3.979 1.25,4.208 0.24,0.229 10 false *g 2.938,0.635 3.25,0.792 0.313,0.156 10 false *a 0.781,2.979 1.094,3.135 0.313,0.156 10 false *a
*1 Fuel Tube Sub-assembly (Vehicle Side)
*a SST (Hose Band)
*b SST (T Joint)
*c SST (Gauge)
*d SST (Hose Joint)
*e SST (Hose)
*f SST (Fuel Tube Connector)
*g Fuel Pipe (Vehicle Side)


Install SST (EFI fuel pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)


h.

Wipe up any spilled fuel.


i.

Connect the cable to the negative (-) battery terminal.

Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



j.

Measure the fuel pressure.

NOTICE:

Do not start the engine.


Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 40
Standard Fuel Pressure:

196 to 833 kPa (2.0 to 8.5 kgf/cm2, 28 to 121 psi)


·

If the fuel pressure is more than the standard, replace the fuel main valve assembly.

·

If the fuel pressure is less than the standard, check the fuel hoses and their connections, fuel pump and fuel main valve assembly.



k.

Disconnect the GTS from the DLC3.


l.

Start the engine.


m.

Measure the fuel pressure at idle.

Standard Fuel Pressure:

196 to 833 kPa (2.0 to 8.5 kgf/cm2, 28 to 121 psi)


HINT:

Refer to Standard Idle Speed.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION



n.

Stop the engine.


o.

Check that the fuel pressure remains as specified for 5 minutes.

Standard Fuel Pressure:

98 kPa (1.0 kgf/cm2, 14.2 psi) or more


If the result is not as specified, check the fuel pump, fuel main valve assembly and/or port fuel injector assemblies.


p.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST (EFI fuel pressure gauge) to prevent fuel from spraying.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



q.

Connect the fuel tube sub-assembly (for Port Injection).

i.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



r.

Connect the No. 2 fuel tube sub-assembly (for Direct Injection).

i.

Connect the No. 2 fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



s.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


t.
A412603C01
0.833,2.042 1.354,2.042 1.354,2.042 1.354,1.854 false 1.125,2.042 1.125,1.771 false 2.646,1.792 2.052,1.792 2.052,1.792 2.052,1.438 true 2.26,1.792 2.26,1.583 true 0.667,1.948 0.979,2.104 0.313,0.156 10 false *a 2.677,1.708 2.99,1.865 0.313,0.156 10 false *b
*a Protrusion
*b Notch


Align the protrusions of the No. 2 fuel pipe clamp with the notches of the No. 1 fuel pipe clamp, and engage the 2 claws to install the No. 2 fuel pipe clamp.


u.

Connect the cable to the negative (-) battery terminal.

Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




Hide 3.CHECK FUEL PRESSURE (for High Pressure)

a.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205

b.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Fuel Pressure (High)
Injection Mode
50003 372 211,265,294
Standard:
GTS Display Condition Specified Condition
Fuel Pressure (High)
·

Shift position: P

·

A/C: Off

·

Engine warmed up

·

Engine Speed: 3000 rpm

·

Injection Mode: Direct


2400 to 20000 kPag


If the result is not as specified, check the fuel pump (for Low Pressure), fuel pump assembly (for High Pressure), fuel pressure sensor (fuel delivery pipe with sensor assembly LH) (for High Pressure) and wire harnesses.