Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR BELT MOULDING › 2020.02–2020.11
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0417662 REAR DOOR BELT MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR BELT MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door belt moulding assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Rear door glass sub-assembly LH*

·

Rear door glass sub-assembly RH*

·

Rear door glass run LH*

·

Rear door glass run RH*


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Rear door glass sub-assembly LH*

·

Rear door glass sub-assembly RH*

·

Rear door glass run LH*

·

Rear door glass run RH*


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Hide 69278C 5.REMOVE REAR DOOR INSIDE HANDLE BEZEL

Hide 67604 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 68174A 7.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Hide 67225A 8.REMOVE QUARTER WINDOW UPPER STOP

Hide 67842E 9.REMOVE REAR DOOR SERVICE HOLE COVER

Hide 68152C 10.REMOVE REAR DOOR GLASS RUN

Hide 67408E 12.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Hide 68124B 13.REMOVE REAR DOOR QUARTER WINDOW GLASS

Hide 68104 14.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Hide 75740 15.REMOVE REAR DOOR BELT MOULDING ASSEMBLY

a.
B564622C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear door belt moulding assembly as shown in the illustration.


b.
B564623C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 6 claws to remove the rear door belt moulding assembly as shown in the illustration.