Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM37A0E _58 Vehicle Interior _086884 DOOR LOCK _0417743 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 69760C 2.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B563681C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door inside locking cable assembly as shown in the illustration.


Hide 69720B 3.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B563682C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door lock remote control cable assembly as shown in the illustration.


Hide 69036A 4.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY

a.
B563683C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws as shown in the illustration.


b.
B563684C01
0,0 0,0 false

Engage the 2 claws to install the front door lock cover sub-assembly as shown in the illustration.


Hide 69040A 5.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing a removed front door lock with motor assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock with motor assembly.



a.

Apply MP grease to the sliding parts of the front door lock with motor assembly.


b.

When reusing the front door lock with motor assembly:

i.

Install a new door lock wiring harness seal to the front door lock with motor assembly.



c.
B563685C01
3.01,2.865 2.792,2.583 true 3.042,2.792 3.229,2.979 0.188,0.188 10 true *1
*1 Front Door Lock Open Rod
V113147

Install in this Direction


Connect the front door lock open rod to the front door lock with motor assembly as shown in the illustration.

HINT:

Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.



d.

Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 67832 6.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 67869J 7.INSTALL FRONT DOOR WEATHERSTRIP CLIP

Hide 67602 8.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 81230N 9.INSTALL COURTESY LIGHT ASSEMBLY

Hide 69278B 10.INSTALL FRONT DOOR INSIDE HANDLE BEZEL

Hide 11.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Hide 12.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Hide 67492A 13.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 58441L 15.INSTALL BATTERY SERVICE HOLE COVER (for HV Model)

Hide 16.INITIALIZE POWER WINDOW CONTROL SYSTEM