Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418597 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 67862 2.INSTALL FRONT DOOR WEATHERSTRIP

a.
B563824

Engage the 24 clips to install the front door weatherstrip.


Hide 68620 3.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Clean the bolt hole in the vehicle body.


b.

Clean the threads of the bolt.


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
B563822C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Install the front door check assembly with the 2 nuts and bolt.

Torque:
Bolt : 27 N*m (275 kgf*cm, 20 ft.*lbf)
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67837B 4.INSTALL FRONT DOOR DUST PROOF SEAL

a.
B563821

Engage the 3 claws to install 3 new front door dust proof seals.


Hide 75793 5.INSTALL FRONT DOOR UPPER OUTSIDE MOULDING PAD

Hide 6.INSTALL FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 67001A 7.INSTALL FRONT DOOR PANEL CUSHION

a.
B563820

Engage the claw to install a new front door panel cushion.


Hide 75792 8.INSTALL DOOR WINDOW FRAME MOULDING CLIP

a.
B563819

Engage the 2 claws to install the door window frame moulding clip.


Hide 67496C 9.INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER

Hide 75754A 10.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 75756D 11.INSTALL FRONT DOOR WINDOW FRAME MOULDING

Hide 75720 12.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY

Hide 69312 13.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B563817C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Install the front door lock open rod as shown in the illustration.


Hide 69202A 14.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B563815C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and claw as shown in the illustration.


c.
B563813

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.
B563812

Engage the clamp.


Hide 69040A 15.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

Hide 69242E 16.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B563811

Engage the 3 guides and claw to install the front door rear outside handle pad.


Hide 69241H 17.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B563810

Engage the guide and 2 claws to install the front door front outside handle pad.


Hide 18.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B563807

Using a T30 "TORX" socket wrench, install the front door lock cylinder assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B563806

Install the hole plug.


Hide 69217D 19.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B563809

Engage the 2 claws.


b.

Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B563808

Install the hole plug.


Hide 69220 20.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B563805C01
0,0 0,0 false
V113147

Install in this Direction


Insert the front end of the front door outside handle assembly into the front door outside handle frame sub-assembly.


b.

Insert the rear end of the front door outside handle assembly into the front door outside handle frame sub-assembly, then slide the front door outside handle assembly toward the front of the vehicle to install it.


c.
B563803

Move the lever as shown in the illustration and engage the 2 claws to lock the front door outside handle assembly.


d.
B563801

Connect the connector.


e.
B563799

Engage the 2 claws as shown in the illustration.


Hide 67404F 21.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B563797C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


b.

Install the front door rear lower frame sub-assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 68151D 22.INSTALL FRONT DOOR GLASS RUN

a.
B563795

Install the front door glass run.


Hide 23.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.
B563794

Install the front door window regulator assembly with the 7 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Connect the connector.


Hide 68102 24.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

for Driver Side:

i.

Connect the power window regulator master switch assembly.



b.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly.



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON.


e.

Move the front door window regulator assembly so that the door glass bolt holes can be seen.


f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

for Driver Side:

i.

Disconnect the power window regulator master switch assembly.



i.

for Front Passenger Side:

i.

Disconnect the power window regulator switch assembly.



j.
B563792C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.


k.
B563790

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


l.
B563789

Install the hole plug.


Hide 89860A 25.INSTALL SIDE AIRBAG SENSOR ASSEMBLY

Hide 67832 26.INSTALL FRONT DOOR SERVICE HOLE COVER

a.
B563788

Engage the 5 clips to install the front door service hole cover.


b.
B563787

Engage the 6 clamps.


c.

Connect the connector.


Hide 67869J 27.INSTALL FRONT DOOR WEATHERSTRIP CLIP

a.
B563786

Insert the 3 front door weatherstrip clips and turn them 45 degrees as shown in the illustration to install them.


Hide 86160 28.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 67856D 29.INSTALL FRONT DOOR PANEL PROTECTOR

a.
B563784C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door panel protector as shown in the illustration.


Hide 67838A 30.INSTALL FRONT DOOR VENT SEAL

a.
B563782C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 guides to install the front door vent seal to the front door inner glass weatherstrip as shown in the illustration.


Hide 68172A 31.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

a.
B563780C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door inner glass weatherstrip as shown in the illustration.


Hide 32.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

Hide 87964 33.INSTALL OUTER MIRROR INSTALL HOLE COVER

Hide 89430 34.INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)

Hide 67664C 35.INSTALL DOOR FRAME GARNISH

a.
B563778C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides as shown in the illustration.


b.

Engage the clip to install the door frame garnish.


Hide 84927 36.INSTALL SEAT MEMORY SWITCH (w/ Seat Memory Switch)

Hide 74038C 37.INSTALL DOOR ARMREST COVER SUB-ASSEMBLY

a.
B563776C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the door armrest cover sub-assembly as shown in the illustration.


Hide 69206B 38.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B563774

Engage the 3 claws to install the front door inside handle sub-assembly.


Hide 67602 39.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B563773C01
2.146,1.021 2.563,0.604 true 2.083,1.677 2.083,1.385 true 2.573,0.49 2.792,0.667 0.219,0.177 10 true *1 2,1.688 2.219,1.875 0.219,0.188 10 true *2
*1 Front Door Inside Lock/Unlock Knob Locking Cable
*2 Front Door Lock Open Lever Remote Control Cable
V113147

Install in this Direction


Connect the front door lock open lever remote control cable and front door inside lock/unlock knob locking cable to the front door inside handle sub-assembly as shown in the illustration.


b.

w/ Illumination:

i.
B563770

Connect the connector.


ii.

Engage the clamp.



c.

w/ Seat Memory Switch:

i.
B563771

Connect the connector.



d.
B563769C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide, 4 claws and 10 clips as shown in the illustration.


e.
B563766

Install the front door trim board sub-assembly with the 3 screws.


f.
B563765

Engage the claw as shown in the illustration.


Hide 81230N 40.INSTALL COURTESY LIGHT ASSEMBLY

Hide 69278B 41.INSTALL FRONT DOOR INSIDE HANDLE BEZEL

a.
B563763

Engage the 3 claws to install the front door inside handle bezel.


Hide 42.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

a.

Connect each connector.


b.
B566538

Engage the 5 guides, 4 claws and 2 clips to install the multiplex network master switch assembly with front door upper armrest base panel.


Hide 43.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

a.

Connect the connector.


b.
B566541

Engage the 5 guides, 6 claws and 2 clips to install the power window regulator switch assembly with front door upper armrest base panel.


Hide 67492A 44.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B563755

Engage the guide and clip to install the front door lower frame bracket garnish.


Hide 45.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 58441L 46.INSTALL BATTERY SERVICE HOLE COVER (for HV Model)

Hide 47.INITIALIZE POWER WINDOW CONTROL SYSTEM

Hide 50.PERFORM CALIBRATION (w/ Panoramic View Monitor System)