Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0417748 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

If the entry lock and wireless door lock operations cannot be performed, the electrical key and tire pressure warning ECU and receiver may be malfunctioning, or there may be wave interference or problems in the communication which is used for the entry and wireless function between the electrical key and tire pressure warning ECU and receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B556631E01
0.708,8.448 4.375,8.646 3.667,0.198 10 false : CAN Communication Line 0.563,7.729 2.25,8.198 1.688,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 5.167,8 6.854,8.469 1.688,0.469 10 false Certification ECU (Smart Key ECU Assembly) 0.906,4.792 2.594,5.26 1.688,0.469 10 false IC 0.26,6.104 1.948,6.573 1.688,0.469 10 false M51 1.74,5.854 2.219,6.229 0.479,0.375 10 false GND 1.667,5.313 2.146,5.688 0.479,0.375 10 false CSEL 5.271,5.323 5.75,5.698 0.479,0.375 10 false CSEL 5.281,4.698 5.76,5.073 0.479,0.375 10 false RDAM 1.656,4.698 2.135,5.073 0.479,0.375 10 false DATA 1.865,4.083 2.344,4.458 0.479,0.375 10 false +5 5.292,4.083 5.771,4.458 0.479,0.375 10 false RCO 1.896,3.792 2.375,4.167 0.479,0.375 10 false IG 5.781,4.938 6.125,5.208 0.344,0.271 10 false +B 5.771,4.323 6.115,4.594 0.344,0.271 10 false +B 5.76,3.698 6.104,3.969 0.344,0.271 10 false 5 V 5.281,2.094 5.76,2.469 0.479,0.375 10 false +B 5.292,1.469 5.771,1.844 0.479,0.375 10 false ACCD 5.292,1.01 5.771,1.385 0.479,0.375 10 false IG1D 5.281,0.469 5.76,0.844 0.479,0.375 10 false CUTB 0.26,0.448 2.198,0.802 1.938,0.354 10 false from ECU-DCC NO. 2 Fuse 0.75,0.979 2.688,1.333 1.938,0.354 10 false to IG1-NO. 1 Relay 1.073,1.552 3.01,1.906 1.938,0.354 10 false to ACC Relay 0.604,2.177 2.542,2.531 1.938,0.354 10 false from Auxiliary Battery 0.594,2.99 2.531,3.344 1.938,0.354 10 false from ECU-IG1 NO. 3 Fuse 2.531,2.344 4.469,2.698 1.938,0.354 10 false AM2 4.917,2.198 5.271,2.49 0.354,0.292 10 false H48 4.927,1.573 5.281,1.865 0.354,0.292 10 false H48 4.917,1 5.271,1.292 0.354,0.292 10 false H48 4.917,0.448 5.271,0.74 0.354,0.292 10 false H48 4.938,4.188 5.292,4.479 0.354,0.292 10 false M5 4.927,4.802 5.281,5.094 0.354,0.292 10 false M5 4.927,5.427 5.281,5.719 0.354,0.292 10 false M5 4.948,5.219 5.302,5.51 0.354,0.292 10 false 20 4.958,4.594 5.313,4.885 0.354,0.292 10 false 19 4.948,3.99 5.302,4.281 0.354,0.292 10 false 18 2.146,3.698 2.5,3.99 0.354,0.292 10 false 1 2.156,4.083 2.51,4.375 0.354,0.292 10 false 8 2.156,4.688 2.51,4.979 0.354,0.292 10 false 2 2.156,5.323 2.51,5.615 0.354,0.292 10 false 6 2.146,5.729 2.5,6.021 0.354,0.292 10 false 12 6.25,1.74 6.688,2 0.438,0.26 10 false IC 5.76,1.708 6.104,1.979 0.344,0.271 10 false +B 5.76,1.063 6.104,1.333 0.344,0.271 10 false +B 4.99,1.99 5.344,2.281 0.354,0.292 10 false 4 4.969,1.375 5.323,1.667 0.354,0.292 10 false 16 4.948,0.802 5.302,1.094 0.354,0.292 10 false 17 4.948,0.25 5.302,0.542 0.354,0.292 10 false 15 0.26,6.24 2.229,6.688 1.969,0.448 10 false Electrical Key and Tire Pressure Warning ECU and Receiver

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR

·

After repair, confirm that no DTCs are output.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

It is necessary to perform initialization after registration of the transmitter IDs into the electrical key and tire pressure warning ECU and receiver if the electrical key and tire pressure warning ECU and receiver has been replaced.


·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage.*1


b.

Measure the auxiliary battery voltage with the ignition switch off.*2

·

*1: for Gasoline Model

·

*2: for HV Model


Standard Voltage:

11 to 14 V


HINT:

It may be possible to tell whether the auxiliary battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

2.CHECK DOOR AJAR WARNING
2.CHECK DOOR AJAR WARNING
a.

When the doors are locked by operating the entry lock function with all doors closed, check that the door ajar warning operates.

HINT:

Be sure to check the following before performing the procedure.

·

Ignition switch is off.

·

All the doors is close.

·

The lock sensor is on or lock switch is pressed on the electrical key transmitter sub-assembly.

·

Electrical key transmitter sub-assembly is in the vehicle exterior detection area.




Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

3.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

GO TO LIGHTING SYSTEM (Proceed to Door Courtesy Switch Circuit)

3.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Power door lock function operates normally A
Power door lock function does not operate normally B



A

4.CHECK KEY DIAGNOSTIC MODE

B

4.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
i.
B560851C01
2.198,1.063 2.51,1.26 0.313,0.198 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for driver door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




ii.
B560854C01
1.344,1.052 1.656,1.208 0.313,0.156 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for front passenger door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iii.
B560861C01
0.635,1.135 2.833,0.25 2.833,0.25 3,0.25 false 2.063,1.135 2.833,0.25 false 3.031,0.177 3.344,0.375 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iv.
B560862C01
0.688,0.313 2.75,0.083 2.75,0.083 3,0.083 false 2.052,0.302 2.75,0.083 false 3.031,0.031 3.344,0.229 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




v.
B560864C01
1.365,1.698 2.583,0.167 2.583,0.167 2.833,0.167 false 1.948,1.333 2.583,0.167 false 2.885,0.083 3.198,0.281 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 3 indoor electrical key antenna assembly (inside luggage compartment):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




vi.
B560863C01
1.771,1.219 2.083,1.417 0.313,0.198 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (outside luggage compartment):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless buzzer sounds.




Result:
Result Proceed to
Key diagnostic mode inspections fail for both channels A
Key diagnostic mode inspections succeed for both channels B
Key diagnostic mode inspection succeeds for only one of the channels C



A

5.CHECK WAVE ENVIRONMENT

B

17.PERFORM REGISTRATION

C

25.CHECK WAVE ENVIRONMENT
5.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the electrical key and tire pressure warning ECU and receiver and perform a wireless operation 2 or more times*.

*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.


HINT:
·

When the electrical key transmitter sub-assembly is brought near the electrical key and tire pressure warning ECU and receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
Wireless function does not operate normally A
Wireless function operates normally B



A

6.CHECK TRANSMITTER BATTERY

B

AFFECTED BY WAVE INTERFERENCE

6.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine*1 or hybrid control system*2 by holding the electrical key transmitter sub-assembly near the engine switch*1 or power switch*2, depressing the brake pedal and pressing the engine switch*1 or power switch*2.

*1: for Gasoline Model

*2: for HV Model






Result:
Result Proceed to
LED illuminates 3 times or more when switch is pressed and held A
LED does not illuminate when switch is pressed and held B
LED illuminates once or twice but not a third time C



A

7.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

16.INSPECT TRANSMITTER BATTERY

C

REPLACE TRANSMITTER BATTERY

7.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

8.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

9.CHECK ENTRY OPERATION
8.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK ENTRY OPERATION
9.CHECK ENTRY OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check that the function operates normally.


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER AND BODY GROUND)

B

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER AND BODY GROUND)
a.

Disconnect the M5 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the M51 electrical key and tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M5-18 (RCO) - M51-8 (+5) Always Below 1 Ω
M5-19 (RDAM) - M51-2 (DATA) Always Below 1 Ω
M5-20 (CSEL) - M51-6 (CSEL) Always Below 1 Ω
M51-12 (GND) - Body ground Always Below 1 Ω
M5-18 (RCO) or M51-8 (+5) - Other terminals and body ground Always 10 kΩ or higher
M5-19 (RDAM) or M51-2 (DATA) - Other terminals and body ground Always 10 kΩ or higher
M5-20 (CSEL) or M51-6 (CSEL) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK ENTRY OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK ENTRY OPERATION
a.

Connect all connectors and check that the function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

12.CHECK ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

12.CHECK ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER
a.
B389376C62
1.51,0.208 1.917,0.458 0.406,0.25 0.896,1.656 1.375,1.292 false 1.583,0.24 2.042,0.438 0.458,0.198 10 false M51 0.198,0.188 0.427,0.385 0.229,0.198 10 false *a 0.552,1.635 0.979,1.823 0.427,0.188 10 false GND
*a Component with harness connected
(Electrical Key and Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M51-12 (GND) - Body ground Always Below 1 Ω



b.
B416848C91
1.563,0.125 1.958,0.365 0.396,0.24 1.188,1.875 1.417,1.25 false 2.208,1.885 1.979,1.042 false 0.833,0.198 1.146,0.396 0.313,0.198 10 false *a 0.698,2.208 1.01,2.406 0.313,0.198 10 false *b 0.99,4.167 1.302,4.365 0.313,0.198 10 false *c 2.229,4.177 2.542,4.375 0.313,0.198 10 false *d 0.167,3.25 0.563,3.469 0.396,0.219 10 false GND 1.646,0.167 1.958,0.365 0.313,0.198 10 false M51 2.063,1.917 2.76,2.26 0.698,0.344 10 false DATA 1.063,1.906 1.76,2.25 0.698,0.344 10 false GND
*a Component with harness connected
(Electrical Key and Tire Pressure Warning ECU and Receiver)
*b Waveform 1
*c Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*d After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
M51-2 (DATA) - M51-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B562188C01
1.521,0.177 1.865,0.396 0.344,0.219 1.042,1.76 1.365,1.281 false 0.667,1.531 1.354,1.063 false 2.365,1.615 2.073,1.073 false 1.583,0.208 1.896,0.406 0.313,0.198 10 false M51 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 0.906,1.792 1.313,2 0.406,0.208 10 false GND 0.51,1.573 0.917,1.781 0.406,0.208 10 false CSEL 2.344,1.656 2.792,1.885 0.448,0.229 10 false IG
*a Component with harness connected
(Electrical Key and Tire Pressure Warning ECU and Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M51-1 (IG) - M51-12 (GND) Ignition switch ON 10 to 16 V
M51-6 (CSEL) - M51-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors closed


Below 1 V → Pulse generation



b.
B423545C44
1.479,0.125 1.865,0.354 0.385,0.229 2.042,1.844 1.896,1.229 false 0.813,1.802 1.292,1.208 false 0.333,0.25 0.646,0.448 0.313,0.198 10 false *a 0.688,2.219 1,2.417 0.313,0.198 10 false *b 0.198,3.208 0.635,3.427 0.438,0.219 10 false GND 0.948,4.083 1.26,4.281 0.313,0.198 10 false *c 2.01,4.094 2.323,4.292 0.313,0.198 10 false *d 1.563,0.156 1.917,0.375 0.354,0.219 10 false M51 2,1.854 2.313,2.052 0.313,0.198 10 false +5 0.677,1.823 0.99,2.021 0.313,0.198 10 false GND
*a Component with harness connected
(Electrical Key and Tire Pressure Warning ECU and Receiver)
*b Waveform 1
*c Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*d After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
M51-8 (+5) - M51-12 (GND) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

14.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

15.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
15.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless function operates normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

16.INSPECT TRANSMITTER BATTERY

OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY

17.PERFORM REGISTRATION
a.

Perform registration of the B code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

18.CHECK ENTRY OPERATION
18.CHECK ENTRY OPERATION
a.

After completing B code registration, check that the entry lock and unlock functions can be operated 2 times consecutively.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

19.READ VALUE USING GTS (B CODE)

B

END (B CODE REGISTRATION FAILED)

19.READ VALUE USING GTS (B CODE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B Code B code registration status No Regd or Regd No Regd: B code not registered correctly
Regd: B code registered correctly
-
Body Electrical > Entry&Start > Data List
Tester Display
B Code
50003 125 132

Result:
Result Proceed to
"Regd" is displayed on the GTS A
"No Regd" is displayed on the GTS B



A

20.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

20.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage while checking the Data List on the GTS.

i.

Read the Data List according to the display on the GTS.

B560871C03
4.563,0.469 4.958,0.698 0.396,0.229 4.531,2.198 4.333,1.333 false 3.958,2.229 4.24,1.323 false 4.646,0.5 4.958,0.698 0.313,0.198 10 false H48 3.813,2.229 4.24,2.458 0.427,0.229 10 false IG1D 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 4.375,2.219 4.833,2.427 0.458,0.208 10 false ACCD 2.219,0.594 2.531,0.792 0.313,0.198 10 false *A
*A for Gasoline Model - -
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Ignition switch off
ACC ON: Ignition switch ACC
IG ON: Ignition switch ON
ST ON: Sending engine*1 or hybrid control system*2 start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
·

*1: for Gasoline Model

·

*2: for HV Model


Standard Voltage:
Tester Connection Condition Specified Condition
H48-17 (IG1D) - Body ground Ignition switch off Below 1 V
H48-16 (ACCD) - Body ground Ignition switch off Below 1 V




Result:
Proceed to
OK
NG



OK

21.READ VALUE USING GTS (ACC SW, IG SW)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

21.READ VALUE USING GTS (ACC SW, IG SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Ignition switch status OFF or ON OFF: Ignition switch off
ON: Ignition switch ACC
"ON" is also displayed when the ignition switch is ON.
IG SW Ignition switch status OFF or ON OFF: Ignition switch off
ON: Ignition switch ON
"OFF" is also displayed when the ignition switch is ACC.
Body Electrical > Main Body > Data List
Tester Display
ACC SW
IG SW
50003 123 31,30
HINT:

If the certification ECU (smart key ECU assembly) misjudges for any reason that the ignition switch is ON even though the ignition switch is off, the entry lock and unlock functions will be disabled.



Result:
Result Proceed to
The main body ECU (multiplex network body ECU) judges properly that the power source is off when the ignition switch is off A
The main body ECU (multiplex network body ECU) does not judge properly that the power source is off when the ignition switch is off B



A

22.CHECK ENTRY OPERATION

B

TROUBLESHOOT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

22.CHECK ENTRY OPERATION
a.

Disconnect and reconnect the certification ECU (smart key ECU assembly) connectors.



Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

23.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

23.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

24.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
24.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the function operates normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

25.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the electrical key and tire pressure warning ECU and receiver and perform a wireless operation 2 or more times*.

*: When the wireless function is operated, channel 1 and 2 are used alternately. If the first wireless operation is performed successfully and the second wireless operation fails, wave interference may be occurring for either channel.


HINT:
·

When the electrical key transmitter sub-assembly is brought near the electrical key and tire pressure warning ECU and receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
Wireless function does not operate normally A
Wireless function operates normally 1 or more times. B



A

26.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

AFFECTED BY WAVE INTERFERENCE

26.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

27.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

28.CHECK KEY DIAGNOSTIC MODE
27.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

28.CHECK KEY DIAGNOSTIC MODE
28.CHECK KEY DIAGNOSTIC MODE
a.

Enter key diagnostic mode and select the channel for which the wireless door lock buzzer did not sound and perform the inspection again using a different electrical key transmitter sub-assembly than was used in the initial inspection.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

Result:
Result Proceed to
Wireless buzzer does not sound A
Wireless buzzer sounds B



A

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER)

B

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the M51 electrical key and tire pressure warning ECU and receiver connector.


b.

Disconnect the M5 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M51-6 (CSEL) - M5-20 (CSEL) Always Below 1 Ω
M51-6 (CSEL) or M5-20 (CSEL) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

30.CHECK ENTRY OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK ENTRY OPERATION
a.

Connect all connectors and check that the function operates normally.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

31.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

31.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B389376C63
1.531,0.219 1.875,0.427 0.344,0.208 0.823,0.927 1.333,1.052 false 0.896,1.656 1.375,1.292 false 1.594,0.24 2.052,0.438 0.458,0.198 10 false M51 0.198,0.188 0.427,0.385 0.229,0.198 10 false *a 0.427,0.823 0.885,1.021 0.458,0.198 10 false CSEL 0.552,1.635 0.979,1.823 0.427,0.188 10 false GND
*a Component with harness connected
(Electrical Key and Tire Pressure Warning ECU and Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M51-6 (CSEL) - M51-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors closed


Below 1 V → Pulse generation



Result:
Proceed to
OK
NG



OK

32.CHECK ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

32.CHECK ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Enter key diagnostic mode and select the channel for which the wireless buzzer did not sound.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

b.
B416848C92
1.563,0.125 1.958,0.365 0.396,0.24 1.188,1.875 1.417,1.25 false 2.198,1.854 1.958,1.052 false 0.833,0.198 1.146,0.396 0.313,0.198 10 false *a 0.698,2.208 1.01,2.406 0.313,0.198 10 false *b 0.99,4.167 1.302,4.365 0.313,0.198 10 false *c 2.229,4.177 2.542,4.375 0.313,0.198 10 false *d 0.229,3.25 0.625,3.469 0.396,0.219 10 false GND 1.635,0.167 1.979,0.375 0.344,0.208 10 false M51 2.063,1.896 2.76,2.24 0.698,0.344 10 false DATA 1.063,1.906 1.76,2.25 0.698,0.344 10 false GND
*a Component with harness connected
(Electrical Key and Tire Pressure Warning ECU and Receiver)
*b Waveform 1
*c Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*d After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
M51-2 (DATA) - M51-12 (GND) Procedure:
1.

Ignition switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)


HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).



Result:
Proceed to
OK
NG



OK

33.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER

33.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

34.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
34.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the function operates normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)