1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK
Check fuel pump operation.
Do not start the engine.
| Tester Display |
|---|
| Activate the Circuit Relay |
Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank sub-assembly can be heard. If no sounds can be heard, check the relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
2.CHECK FUEL PRESSURE
Discharge fuel system pressure.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
Measure the auxiliary battery voltage.
11 to 14 V
|
Open |
|
Pull |
Open the cover of the EFI fuel pipe clamp and remove the EFI fuel pipe clamp from the fuel tube connector.
Disconnect the fuel tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
| *1 | Fuel Tube Sub-assembly (Vehicle Side) |
| *a | SST (Hose Band) |
| *b | SST (T Joint) |
| *c | SST (Gauge) |
| *d | SST (Hose Joint) |
| *e | SST (Hose) |
| *f | SST (Fuel Tube Connector) |
| *g | Fuel Pipe (Vehicle Side) |
Install SST (EFI fuel pressure gauge) as shown in the illustration.
Wipe up any spilled fuel.
Connect the cable to the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Measure the fuel pressure.
Do not start the engine.
| Tester Display |
|---|
| Activate the Circuit Relay |
294 to 833 kPa (3.0 to 8.5 kgf/cm2, 43 to 121 psi)
If the fuel pressure is more than the standard, replace the fuel main valve assembly.
If the fuel pressure is less than the standard, check the fuel hoses and their connections, fuel pump and fuel main valve assembly.
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
Measure the fuel pressure at idle.
294 to 833 kPa (3.0 to 8.5 kgf/cm2, 43 to 121 psi)
Refer to Standard Idle Speed.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
Disconnect the GTS from the DLC3.
Stop the engine.
Check that the fuel pressure remains as specified for 5 minutes.
98 kPa (1.0 kgf/cm2, 14.2 psi) or more
If the result is not as specified, check the fuel pump, fuel main valve assembly and/or port fuel injector assemblies.
After checking the fuel pressure, disconnect the cable from the negative (-) auxiliary battery terminal and carefully remove SST to prevent fuel from spraying.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Connect the fuel tube sub-assembly to the fuel pipe.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
Install the EFI fuel pipe clamp to the fuel tube connector and close the cover of the EFI fuel pipe clamp.
Connect the cable to the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Inspect for fuel leaks.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
3.CHECK FUEL PRESSURE (for High Pressure)
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off.
| Tester Display |
|---|
| Coolant Temperature |
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| Engine Speed |
| Fuel Pressure (High) |
| Injection Mode |
During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, read the Data List after charge control has completed.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Fuel Pressure (High) | ·
Shift position: P ·
A/C: Off ·
Engine warmed up ·
Engine Speed: 2500 rpm ·
Injection Mode: Direct |
3000 to 25000 kPa |
If the result is not as specified, check the fuel pump, fuel pump assembly, fuel pressure sensor and wire harnesses.