Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (FUEL) › FUEL TANK
RM37A0E _51 Engine / Hybrid System _086907 A25A-FXS, A25B-FXS FUEL _0417790 FUEL TANK A

A25A-FXS, A25B-FXS FUEL  FUEL TANK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

The fuel tank sub-assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank sub-assembly may fall off the engine lifter.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 3.REMOVE BATTERY SERVICE HOLE COVER

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 58166A 5.REMOVE FRONT FLOOR COVER LH

a.
A458437N01
0.969,2.188 1.125,2.385 0.156,0.198 10 true A 1.24,0.896 1.396,1.094 0.156,0.198 10 true A 1.042,1.24 1.198,1.438 0.156,0.198 10 true A 2.521,0.021 2.677,0.219 0.156,0.198 10 true A 2.656,0.313 2.813,0.51 0.156,0.198 10 true A 3.104,1.146 3.26,1.344 0.156,0.198 10 true B 3.125,1.583 3.281,1.781 0.156,0.198 10 true B 3.115,1.979 3.271,2.177 0.156,0.198 10 true B 1.302,0.385 1.458,0.583 0.156,0.198 10 true C 2.99,2.302 3.146,2.5 0.156,0.198 10 true D 2.375,1.729 2.531,1.927 0.156,0.198 10 true D 2.958,2.708 3.115,2.906 0.156,0.198 10 true E 1.448,1.51 1.604,1.708 0.156,0.198 10 true F 1.906,0.656 2.063,0.854 0.156,0.198 10 true F 2.115,1.302 2.271,1.5 0.156,0.198 10 true F 2.917,0.625 3.073,0.823 0.156,0.198 10 true F 2.063,2 2.219,2.198 0.156,0.198 10 true F

Remove the 5 bolts (A), 3 screws (B) and screw (C).


b.

Disengage the 2 clips (D), clip (E) and 5 grommets (F) to remove the front floor cover LH.


Hide 77018E 6.DISCONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

a.
A458418

Disconnect the fuel tank evaporation vent tube sub-assembly from the canister (charcoal canister assembly).

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209F 7.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A458419

Disconnect the fuel tank main tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77201E 8.DISCONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY

a.
A458420

Disconnect the fuel tank filler pipe sub-assembly from the fuel tank sub-assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77001A 9.REMOVE FUEL TANK SUB-ASSEMBLY

CAUTION:

The fuel tank sub-assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank sub-assembly may fall off the engine lifter.


a.
A458421

Disconnect the fuel tank breather tube sub-assembly from the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


b.
A458422

Disconnect the 2 No. 2 floor wire connectors.


c.
A458439

Support the fuel tank sub-assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank sub-assembly horizontal.



d.
A458423

Remove the 5 bolts, No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly.


e.

Lower the engine lifter to remove the fuel tank sub-assembly.

NOTICE:
·

Be careful not to drop the fuel tank sub-assembly.

·

When removing the fuel tank sub-assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




Hide 77018E 11.DISCONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

Hide 77209F 12.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

Hide 77144 13.REMOVE FUEL PUMP GAUGE RETAINER

Hide 77020A 14.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 15.DRAIN FUEL

Hide 77209F 16.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A458424

Disengage the 2 clamps to remove the fuel tank main tube sub-assembly from the fuel tank sub-assembly.


Hide 77018E 17.REMOVE FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

a.
A458425

Disengage the clamp and disconnect the fuel cut off valve with tube assembly from the fuel tank evaporation vent tube sub-assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


b.
A458426

Disengage the 2 clamps to remove the fuel tank evaporation vent tube sub-assembly from the fuel tank sub-assembly.


Hide 18.REMOVE FUEL TANK WIRE

a.
A458427

Disengage the 4 clamps to remove the fuel tank wire from the fuel tank sub-assembly.


Hide 19.REMOVE NO. 3 FUEL TUBE CLAMP

a.
A458428

Disengage the clamp to remove the No. 3 fuel tube clamp from the fuel tank sub-assembly.


Hide 77697 20.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.
A458429

Remove the 3 clips and No. 1 fuel tank heat insulator from the fuel tank sub-assembly.


Hide 77642A 21.REMOVE NO. 2 FUEL TANK PROTECTOR

a.
A458430

Disengage the 2 clips and remove the No. 2 fuel tank protector from the fuel tank sub-assembly.


Hide 77606 22.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A458431

Disengage the 2 claws and remove the No. 1 fuel tank protector sub-assembly from the fuel tank sub-assembly.


Hide 77656B 23.REMOVE NO. 6 FUEL TANK CUSHION

HINT:

Perform this procedure only when replacement of the No. 6 fuel tank cushion is necessary.


a.
A458432

Remove the 5 No. 6 fuel tank cushions from the fuel tank sub-assembly.